SFA GasMonkey Garage GMG29031 Manual de usuario
U.S. Patent No. 6,199,379
Low Prole Service Jack
Model
GMG29031
GMG29031-M0_102017
Read this manual and follow all the Safety Rules and Operating Instructions before using this product.
Capacity
3 Ton
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
!
SFA Companies
© October 2017
To avoid crushing and related injuries:
NEVER work on, under or around a
load supported only by a hydraulic
jack. ALWAYS use a matched pair of
adequately rated jack stands.
WARNING
!
2
SAFETY AND GENERAL INFORMATION
Save these instructions. For your safety, read, understand, and follow the information provided with and on this
device before using. The owner and/or operator shall have an understanding of the device, its operating characteristics
and safety operating instructions before operating the equipment. The owner and/or operator shall be aware that use
and repair of this product may require special skills and knowledge. Instructions and safety information shall be read
to and discussed with the operator in the operator's native language, making sure that the operator comprehends
their contents, before use of this equipment is authorized. If any doubt exists as to the safe and proper use of this
device, remove from service immediately.
Inspect before each use. Do not use if abnormal conditions such as cracked welds, damaged, loose or missing
parts are noted. Any equipment that appears damaged in any way, is found to be worn, or operates abnormally shall
be removed from service until repaired. If the equipment has been or is suspected to have been subjected to an
abnormal load or shock, immediately discontinue use until inspected by a factory authorized repair facility (contact
distributor or manufacturer for list of authorized repair facilities). It is recommended that an annual inspection be
made by an authorized repair facility. Labels and Operator's Manuals are available from the manufacturer.
PRODUCT DESCRIPTION
This Hydraulic Service Jack is designed to lift, but not support, one end of a vehicle. Immediately after lifting, loads
must be supported by a matched pair of appropriately rated jack stands.
WARNING: Never use a hydraulic jack as a stand-alone device. After lifting, immediately support the lifted
vehicle with a matched pair of appropriately rated jack stands.
Figure 1 - Service Jack Nomenclature
!
Saddle
Lift Arm
Handle
Handle
Sleeve
Rear Caster
Vent screw
(ref. Parts illustration
for location)
Front Wheel
3
SPECIFICATIONS
Model Capacity Jack Length Min. Height Max. Height Weight
GMG29031 3.0 Ton 27-1/4" 3-3/8" 19-5/8" 77.0 lbs
PREPARATION
Assembly
1. Assemble the two-piece handle with provided bolt.
2. Insert handle into the handle fork. Tighten the bolt on handle fork to prevent accidental removal of handle while
in use.
WARNING: Do not lift or carry jack by handle. Handle could dislodge and jack fall, resulting in possible injury
or property damage.
Before Use
1. Verify that the product and application are compatible, if in doubt call Tech Service (888) 332-6419.
2. Before using this product, read the operator's manual completely and familiarize yourself thoroughly with the
product, its components and recognize the hazards associated with its use.
3. To familiarize yourself with basic operation, locate and turn the release valve (handle):
a. Clockwise until rm resistance is felt to further turning. This is the ‘CLOSED’ release valve position used to
raise the saddle.
b. Counter-clockwise, but no more than 1/2 turn from the closed position. This is the ‘OPEN’ release valve position
used to lower the saddle.
4. With saddle fully lowered, and release valve closed, pump the operating handle. If lift arm responds immediately,
jack is ready for use. If jack does not respond, follow Bleeding/Venting Trapped Air procedure below.
5. Ensure that jack rolls freely. Raise and lower the unloaded saddle throughout the lifting range before putting into
service to ensure the pump operates smoothly. Replace worn or damaged parts and assemblies with authorized
replacement parts only.
Bleeding/Venting Trapped Air
With the Release Valve in the OPEN position (3b above) and Saddle fully lowered, locate and remove the Oil Filler
Plug/Screw. Pump Handle 6 to 8 full strokes. This will help release any pressurized air which may be trapped within
the reservoir. Check oil level and reinstall Oil Filler Plug/Screw.
!
• Study, understand, and follow all instructions
before operating this device.
• Do not exceed rated capacity.
• Use only on hard, level surface capable of
supporting the load.
• Lifting device only. Immediately after lifting,
support the vehicle with appropriate means.
• Do not move or dolly the vehicle while on the jack.
• Lift only on areas of the vehicle as specied by
the vehicle manufacturer.
• No alterations shall be made to this product.
• Failure to heed these markings may result in
personal injury and/or property damage.
To avoid crushing and related injuries:
•
Never work on, under or around a load supported
only by hydraulic jack.
•
Always use a matched pair of adequately rated
jack stands.
• Chock each unlifted tire in both directions.
• Do not use this device to lift, level, lower, support nor
move a house, mobile home, travel trailer, camper or
any building structure.
• Be alert and sober when using this product. Do not
operate under the inuence of drugs or alcohol.
X
WARNING
!WARNING
!
4
OPERATION
Lifting
1. Follow the vehicle manufacturer’s recommended guidelines for lifting. Engage the emergency brake and chock
each unlifted wheel in both directions to prevent inadvertent vehicle movement.
2.
Close the release valve by turning the handle clockwise until rm resistance is felt.
3. Refer to the vehicle manufacturer owner’s manual to locate approved lifting points on the vehicle. Center jack
saddle under lift point.
4. Pump handle to contact lift point. To lift, continue pumping until load reaches desired height.
5. Transfer the load immediately to a matched pair of appropriately rated jack stands.
Lowering
WARNING: Clear all tools and personnel before
lowering load. Open release valve slowly. The further handle
is turned counter-clockwise, the faster the load will descend. Maintain control of the load at all times.
1. Raise load high enough to clear jack stands.
2.
Remove jack stands.
3. Slowly turn the handle counter-clockwise, but no more than 1/2 full turn. If the load fails to lower:
a. Use a functioning jack to raise the vehicle high enough to reinstall jack stands.
b. Remove the malfunctioning jack and then the jack stands.
c.
Use the functioning jack to lower the
vehicle.
4. After removing jack from under the vehicle, lower lifting arm completely to reduce ram exposure to rust and
contamination.
MAINTENANCE
NOTICE: Use only good quality hydraulic jack oil. Avoid mixing different types of uid and NEVER use brake uid,
turbine oil, transmission uid, motor oil or glycerin. Improper uid can cause premature failure of the jack and the
potential for sudden and immediate loss of load. Premium hydraulic jack oil is recommended.
Adding oil
1. With saddle fully lowered set jack in its upright, level position. Remove vent screw.
2. Fill with oil until ~3/16" above the inner cylinder as seen from the oil ller hole. Reinstall vent screw.
Changing oil
For best performance and longest life, replace the complete uid supply at least once per year.
1. With saddle fully lowered, remove vent screw.
2. Lay the jack on its side and drain the uid into a suitable container.
NOTICE: Dispose of hydraulic uid in accordance with local environmental regulations.
3. Fill with oil until ~3/16" above the inner cylinder as seen from the oil ller hole. Reinstall vent screw.
Lubrication
A periodic coating of light lubricating oil to pivot points, axles and hinges will help to prevent rust and assure that
wheels, casters and pump assemblies move freely. Lubricate lift arm through grease ttings.
Cleaning
Check the pump piston and ram for signs of rust or corrosion. Clean as needed and wipe with an oily cloth.
NOTICE: Do not use sandpaper or abrasive material on ram and pump piston surfaces.
Storage
When not in use, store the jack with saddle fully lowered.
!
5
TROUBLESHOOTING
Symptom Possible Causes Corrective Action
Jack will not lift load • Release valve not tightly closed
• Load is too heavy
• Ensure release valve tightly closed
• Consider higher capacity jack
Jack will lift, but not maintain
pressure
•Release valve not tightly closed
• Hydraulic unit malfunction
•Ensure release valve tightly closed
• Discontinue use, contact
Technical Service
Jack will not lower after unloading • Reservoir overlled
• Linkages binding
• Drain uid to proper level
• Clean and lubricate moving parts
Poor lift performance • Fluid level low
• Hydraulic unit malfunction
• Ensure proper uid level
• Discontinue use, contact
Technical Service
Will not lift to full extension • Fluid level low • Ensure proper uid level
6
1
2
3
7
9
4
812
5
6
10 11
Figure 4 - Replacement Parts Illustration for Model GMG29031.
REPLACEMENT PARTS
Not all components of this product are replacement items. When ordering parts, give model number, part number
and description. Call or write for current pricing: SFA Companies Inc., 10939 N. Pomona Ave., Kansas City,
MO 64153, U.S.A. Tel: (888)332-6419 Fax: (816) 891-6599.
7
(**) Replacement requires special skills, knowledge, and
equipment. Only an authorized service center may perform
the repair and/or replacement of these items.
Item Part No. Description Qty
1 G500-50002-0440 Saddle Pad 1
2 K500-10002-0410 Saddle Holding Block 1
3 K500-10001-0000 Saddle 1
4 G493-10003-0420 Return Spring 2
5 29031-5 Handle Sleeve Assembly 1
6 G489-40006-0000 Handle Lock Fastener 1
7 29031-7 Hydraulic Unit 1
8 G735-32000-0000 U-Joint 1
9 S400-30013-0410 Reservoir Plug 1
10 29031-10 Front Wheel Assembly 2
11 29031-11 Rear Caster Assembly 2
12 29031-12 Handle 1
- 29031-13 Repair Kit, Hydraulic -
Replacement Parts Illustration for Model GMG29031
SFA Companies ©2017
10939 N. Pomona Ave. Kansas City, MO 64153
888-332-6419
8
ONE YEAR LIMITED WARRANTY
For a period of one (1) year from date of purchase, SFA Companies will repair or replace, at its option, without
charge, any of its products, which fails due to a defect in material or workmanship under normal usage. This limited
warranty is a consumer's exclusive remedy.
Performance of any obligation under this warranty may be obtained by returning the warranted product, freight
prepaid, to SFA Companies Warranty Service Department, 10939 N. Pomona Ave., Kansas City, MO 64153.
Except where such limitations and exclusions are specically prohibited by applicable law, (1) THE CONSUMER'S
SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCTS AS
DESCRIBED ABOVE. (2) SFA Companies SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL
DAMAGE OR LOSS WHATSOEVER. (3) ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE
LIMITED TO ONE YEAR, OTHERWISE THE REPAIR, REPLACEMENT OR REFUND AS PROVIDED UNDER THIS
EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER, AND IS PROVIDED IN
LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. (4) ANY MODIFICATION, ALTERATION, ABUSE,
UNAUTHORIZED SERVICE OR ORNAMENTAL DESIGN VOIDS THIS WARRANTY AND IS NOT COVERED BY
THIS WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply
to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty gives you specic legal rights, and you may also have
other rights, which vary from state to state.
SFA Companies ©2017
10939 N. Pomona Ave. Kansas City, MO 64153
888-332-6419
Tabla de contenidos
Otros manuales de Jacobo de SFA
SFA
SFA Pro-Lift F-767 Instrucciones de uso
SFA
SFA AMERICAN LIFTING AL2301 Manual de usuario
SFA
SFA OMEGALIFT 23222C Instrucciones de uso
SFA
SFA Pro-Lift PL2920 Instrucciones de uso
SFA
SFA Pro-Lift G-4030 Instrucciones de uso
SFA
SFA American Lifting AL2300 Instrucciones de uso
SFA
SFA Blackhawk Automotive BH2129 Instrucciones de uso
SFA
SFA Platinum Series Instrucciones de uso
SFA
SFA OMEGALIFT 23221C Instrucciones de uso
SFA
SFA Pro-Lift F-2315PE Instrucciones de uso
