SFA Blackhawk Automotive BH2129 Instrucciones de uso
Model Capacity
BH2129 12 Ton
BH2209 20 Ton
Made in PRC
BH2129-M0 11/07
Blackhawk Automotive is a Licensed Trade Mark Made by SFA Companies, Kansas City, MO
SFA Companies
10939 N. Pomona Ave. Kansas City, MO 64153
Air/ Manual Hydraulic Bottle Jacks
Operating Instructions & Parts Manual
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
!
! ADVERTENCIA
• Leer, comprender, y seguir las instrucciónes antes
de utilizar el aparato.
• El manual de instrucciónes y la información de
seguridad deben estar comunicado en lengua del
operador antes del uso.
• No seguir estas indicaciónes puede causar daños
personales o materiales.
! WARNING
To avoid crushing and related injuries:
NEVER work on, under or around a
load supported only by a hydraulic
jack. ALWAYS use adequately rated
jack stands.
Read this manual and follow all the Safety Rules and Operating Instructions before using this product.
2
SAFETY and GENERAL INFORMATION
Save these instructions.
For your safety read, understand, and follow the information provided with and on this jack.
The owner and operator of this equipment shall have an understanding of this jack and safe operating procedures
before attempting to use. The owner and operator shall be aware that use and repair of this product may require
special skills and knowledge. Instructions and safety information shall be conveyed in the operator's native language
before use of this jack is authorized. If any doubt exists as to the safe and proper use of this jack, remove from service
immediately.
Inspect before each use.
Do not use if broken, bent, cracked, or damaged parts (including labels) are noted. Any jack
that appears damaged in any way, operates abnormally or is missing parts, shall be removed from service immediately
and the manufacturer notified. If you suspect that the jack was subjected to a shock load (a load dropped suddenly,
unexpectedly upon it), immediately discontinue use until the jack has been checked by a factory authorized service
center (contact distributor or manufacturer for list of Authorized Service Centers). It is recommended that an annual
inspection be done by qualified personnel.
Replace worn or damaged parts with Blackhawk authorized replacement
parts only.
Labels and owner’s manuals are available from manufacturer.
PRODUCT DESCRIPTION
Blackhawk Automotive Air Actuated Hydraulic Bottle Jack is designed to lift, not support, rated capacity loads consisting
of one end of a vehicle. Immediately after lifting, the load must be supported by a pair of appropriately rated jack
stands. Ensure that air source can dedicate 7.8 CFM @ 110-175 psi to each jack operated. A minimum of 150 psi
air pressure is required to raise rated capacity load.
Never use hydraulic jack as a stand alone device. After lifting, immediately support the lifted load
with a pair of appropriately rated jack stands.
!
PREPARATION
Before Use
1. Verify that the product and the application are compatible, if in doubt contact Customer Support (816)891-6390.
2. Before using this product, read the operator's manual completely and familiarize yourself thoroughly with the
product, its components and recognize the hazards associated with its use.
3. Assemble handle, ensure spring clips align with slots.
4. To familiarize yourself with basic operation, use the notched end of provided handle to engage and turn the release
valve:
a. Clockwise until firm resistance is felt to further turning. This is the ‘CLOSED’ release valve position used to
raise the ram plunger.
b. Counter-clockwise, but no more than 1/2 turn from the closed position. This is the ‘OPEN’ release valve
position used to lower the ram plunger.
5. With ram plunger fully retracted, locate and remove the oil filler plug/screw. Insert the handle into the handle sleeve,
then pump 6 to 8 strokes. This will help release any pressurized air, which may be trapped within the reservoir.
Ensure the oil level is just below the oil filler hole. Reinstall the oil filler plug/screw.
6. Pour a teaspoon of good quality, air tool lubricant into the air supply inlet of the lift control valve. Connect to air
supply and operate for 3 seconds to evenly distribute lubricant.
7. This product is equipped with the popular 1/4" NPT air coupler. When installing a different air coupler of your
choice, ensure that thread tape or compound is used when servicing connections. To ensure dependable, trouble
free operation an inline air dryer and oiler is recommended.
8. Check that the pump operates smoothly and that the extension screw will thread up/down easily before putting
into service. Replace worn or damaged parts and assemblies with Blackhawk Automotive authorized replacement
parts only.
Bleeding / Venting Trapped Air
With the release valve in the OPEN position (4b above) and with ram plunger fully lowered, locate and remove the
oil filler plug/screw. Insert the handle into the handle sleeve; then pump 6 to 8 full strokes. This will help release any
pressurized air which may be trapped within the reservoir. Oil level should be even with the bottom of the oil filler
hole. Reinstall the oil filler plug/screw.
Figure 1 - Air Bottle Jacks Nomenclature (BH2129 shown)
SPECIFICATIONS
Model Capacity Base Size (L x W) Min. Height Max. Height Volume Hyd. Oil Net Weight
BH2129 12 Ton 8 7/8" x 5 3/4" 9 1/2" 18 5/8" 12.2 OZ/ 360 mL 26.7 lb.
BH2209 20 Ton 9 1/4" x 6 3/4" 9 1/2" 18 1/4" 16.7 OZ/ 500 mL 36.4 lb.
3
Air Hose
Handle
Lift Control Valve
Release Valve
Oil Filler Plug*
Carry Handle
Air Motor
Ram Plunger
Saddle
Handle Sleeve
(*) oil filler screw for BH2209
4
!
Only attachments and/or adapters supplied
by the manufacturer shall be used. Lift only
on areas of the vehicle as specified by the vehicle
manufacturer.
! WARNING
• Study, understand, and follow all printed materials
provided with/on this product before use.
• Do not exceed rated capacity.
• This is a lifting device only!
• Immediately after lifting, support the load with
a pair of appropriately rated jack stands.
• Use only on hard, level surface.
• Do not use adapters or accessories that are not
provided initially.
• Lift only on areas of the vehicle as specified by the
vehicle manufacturer.
• Never wire, clamp or otherwise disable the lift
control valve to function by other than operator's
hand.
• No alterations shall be made to this product.
• Failure to heed these markings may result in
personal injury and/or property damage.
To avoid crushing and related injuries:
•
Never work on, under or around a load supported
only by hydraulic jack.
•
Always use adequately rated jack stands.
• Chock each unlifted tire in both directions.
• Do not use this device to lift, level, lower, support nor
move a house, mobile home, travel trailer, camper or
any building structure.
• Be alert and sober when using this product. Do not
operate under the influence of drugs or alcohol.
! WARNING
X
OPERATION
Raising the Ram Plunger
1. Assemble handle, ensure that spring clips align with slots.
2. Place vehicle in the park, with emergency brake on and wheel securely chocked to prevent inadvertent vehicle
movement.
3. Locate and close release valve by turning handle clockwise until firm resistance is felt to further thread
engagement.
4. Verify lift point, center jack saddle under lift point.
5. Squeeze the lift control valve or insert handle into handle sleeve and pump to contact lift point. To lift, continue
pumping until load reaches desired height. DO NOT OPERATE BY AIR AND BY HAND PUMPING AT THE
SAME TIME.
6. Immediately secure lifted load with appropriately rated jack stands.
Use only the handle provided by jack manufacturer. The handle provided with this jack will safely engage
the release valve and operate the handle sleeve. If handle is worn, operates abnormally, or will not positively
engage the release valve, STOP, discontinue use of the jack until a factory replacement handle can be acquired.
Do not use an extender on the air hose or the operating handle.
Lowering
Make certain that all personnel are clear of the load before lowering. Control the rate of descent of the
load at all times. The more you open the release valve, the faster the load descends.
1. Raise load high enough to clear the jack stands, then carefully remove jack stands (always used in pairs).
2. Slowly turn the handle counter-clockwise, but no more than 1/2 turn. If the load fails to lower:
a. Use another jack to raise the vehicle high enough to reinstall jack stands.
b. Remove the affected jack and then the stands.
c. Lower the load by turning the release valve counter-clockwise, but no more than 1/2 turn.
3. After removing jack from under the load, push ram and handle sleeve down to reduce exposure to rust and
contamination.
!
!
!
MAINTENANCE
Important: Use only a good grade hydraulic jack oil. Avoid mixing different types of fluid and NEVER use brake fluid,
turbine oil, transmission fluid, motor oil or glycerin. Improper fluid can cause premature failure of the jack and the
potential for sudden and immediate loss of load. We recommend Hein-Werner HW93291 or equivalent.
Adding oil
1. With ram plunger fully lowered and pump piston fully depressed, set jack in its upright, level position. Remove oil
filler screw/plug.
2. Fill with oil until just below the rim of the oil filler screw/plug hole. Reinstall the oil filler screw/plug.
Changing oil
For best performance and longest life, replace the complete fluid supply at least once per year.
1. With ram plunger fully lowered and pump piston fully depressed, remove the oil filler screw/plug.
2. Lay the jack on its side and drain the fluid into a suitable container.
Note: Dispose of hydraulic oil in accordance with local regulations.
3. Fill with oil until just below the rim of the oil filler screw/plug hole. Reinstall the oil filler screw/plug.
Lubrication
1. A periodic coating of light lubricating oil to pivot points, axles and hinges will help to prevent rust and assure that
pump assemblies move freely.
2. When used on a daily basis, air pump should be internally lubricated before each use. Use only good quality air
tool lubricant. If no inline oiler is used, pour a teaspoon of air tool oil into the inlet of the air control valve. Simply
operate the jack using the air feature in order to fully distribute the oil.
Cleaning
Periodically check the pump piston and ram plunger for signs of rust or corrosion. Clean as needed and wipe with an
oily cloth.
Note: Never use sandpaper or abrasive material on these surfaces!
Storage
When not in use, store the jack with pump piston and ram plunger fully retracted and air supply disconnected.
5
TROUBLESHOOTING
Symptom Possible Causes Corrective Action
Jack will not lift load • Release valve not tightly closed
• Overload condition
• Air pressure inadequate
• Ensure release valve tightly closed
• Remedy overload condition
• Ensure adequate air pressure
Jack will lift, but not maintain
pressure
• Release valve not tightly closed
• Hydraulic unit malfunction
• Ensure release valve tightly closed
• Contact Blackhawk Tech. Service
Jack will not lower after
unloading
• Reservoir overfilled • Ensure load is removed, then drain
fluid to proper level
Poor lift performance • Fluid level low
• Air trapped in system
• Ensure proper fluid level
• With ram fully retracted, remove oil
filler plug/screw to let pressurized
air escape, then reinstall oil filler
plug/screw
Will not lift to full extension • Fluid level low • Ensure proper fluid level
1
Figure 2 - Replacement Parts Illustration for Model BH2129 & BH2209 (BH2209 shown)
REPLACEMENT PARTS
Not all components of the jack are replacement items, but are illustrated as a convenient reference of location and
position in the assembly sequence. When ordering parts, give Model number, serial number and parts description.
Call or write for current pricing: SFA Companies Inc. 10939 N. Pomona Ave. Kansas City, MO 64153, U.S.A.
Tel: (816)891-6390 Fax: (816)891-6599 E-Mail: [email protected]
6
2
3
4
5
6
7
8
9
10
11
12
13b
13a
14
15
16
17
18
A
B
C
D
E
F
T
G
G
H
K
I
J
L
M
N
O
P
Q
R
S
19
7
Item Part# for BH2129 Part# for BH2209 Description Qty
1 A20060-0003 Release Valve 1
2 A20060-0004 O-ring 1
3 A27010-0002 Air Inlet Swivel 1
4 A20060-0005 Air Hose Assembly 1
5 A20060-0006 Air Hose 1
6 A20060-0007 Lift Control Valve 1
7 B20600-0001 Hyd. Cartridge 1
8A20060-0008 Handle Socket 1
9A20060-0001 Handle Assy. 1
10 A20060-0009 Hyd. Cartridge 1
11 F36100-0002 Snap Pin 2
12 A20060-0010 Pin 2
13a F36100-0001 N/A Filler Plug 1
13b N/A A20060-0002 Filler Screw 1
14 A24060-0002 A20060-0013 Reservoir 1
15 A27010-0001 Air Motor 1
16 A20060-0011 Pump Cylinder 1
17 B20600-0002 Washer 1
18 A20060-0014 Pump Piston 1
19 A270-01100-0000 Piston, Air Motor #15
20 A24060-0000 A20060-0000 Seal Kit (includes 2,13 & A ~ T) 1
21 A27010-0000 Seal Kit, Air Motor #15 1
22 BH2129-L0 BH2209-L0 Label (s) 1
23 BH2129-M0 Manual 1
Item Description Qty
2 O-ring 1
13 Filler Plug/ Screw 1
A O-ring 1
B Back-up Ring 1
C O-ring 1
D Back-up Ring 1
E Ram Bearing 1
F U-cup 1
G Filter 2
H Dust Seal 1
I Oil Seal 1
Item Description Qty
J Steel Ball, D4 1
K O-ring 1
L Steel Ball, D5 1
M Steel Ball, D3 1
N Seal 1
O Safety Valve Cap 1
P U-seal 1
Q U-cup 1
R Back-up Ring 1
S O-ring 1
T O-ring
(for BH2209 only)
1
Seal Kit (Item#20) Contents:
Replacement Parts List for Model BH2129 & BH2209
ONE YEAR LIMITED WARRANTY
For a period of one (1) year from date of purchase, SFA Companies will repair or replace, at its option,
without charge, any of its products which fails due to a defect in material or workmanship under normal usage. This
limited warranty is a consumer's exclusive remedy.
Performance of any obligation under this warranty may be obtained by returning the warranted product, freight
prepaid, to SFA Companies Warranty Service Department, 10939 N. Pomona Ave., Kansas City, MO 64153.
Except where such limitations and exclusions are specifically prohibited by applicable law,
(1) THE CONSUMER'S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF
DEFECTIVE PRODUCTS AS DESCRIBED ABOVE.
(2) SFA Companies SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGE OR LOSS
WHATSOEVER.
(3) ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO ONE YEAR,
OTHERWISE THE REPAIR, REPLACEMENT OR REFUND AS PROVIDED UNDER THIS EXPRESS LIMITED
WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED.
(4) ANY MODIFICATION, ALTERATION, ABUSE, UNAUTHORIZED SERVICE OR ORNAMENTAL DESIGN VOIDS
THIS WARRANTY AND IS NOT COVERED BY THIS WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not
apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also
have other rights, which vary from state to state.
SFA Companies
10939 N. Pomona Ave. Kansas City, MO 64153
816-891-6390
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Jacobo de SFA
SFA
SFA OMEGA 21030B Instrucciones de uso
SFA
SFA Platinum Series Instrucciones de uso
SFA
SFA Pro-Lift G-4030 Instrucciones de uso
SFA
SFA Pro-Lift F-767 Instrucciones de uso
SFA
SFA American Lifting AL2300 Instrucciones de uso
SFA
SFA Pro-Lift PL2920 Instrucciones de uso
SFA
SFA GasMonkey Garage GMG29031 Manual de usuario
SFA
SFA Pro-Lift F-2315PE Instrucciones de uso
SFA
SFA AMERICAN LIFTING AL2301 Manual de usuario
SFA
SFA OMEGALIFT 23221C Instrucciones de uso
