70
1.
you use auto iris lens, select this OFF.
2. BLC(Blacklight Compensation): ON/OFF
BLC ON: When the image is in front of strong background lighting, your camera
allows you to get the clear image.
BLC OFF: Deactivation
3. AGC (Auto Gain Control): ON/OFF
AGC ON: Gain is increased or decreased automatically depending on different
illumination.
AGC OFF: Deactivation
4. (H-MIRROR): when this switch is set to ON, the camera image is reversed
horizontally. If you want to monitor your site using a mirror, you can use this feature
to see the right image.
AES ON/OFF: AE: When you use fix or manual iris lens, select this ON. When
Installing camera
Before installation
You have to check whether the location (ceiling or wall) can bear five times
the weight of your camera.
Don’t let the cable to be caught in improper place or the electric line cover
to be damaged. Otherwise it may cause a break do within or fire.
When installing your camera, don’t allow any person to approach the
installation site. If you have any valuable thing sunder the place, move
them away.
Before installing your camera, you have to read the following cautions:
355
90
Lens rotation
Note: The CAMERA FRONT sign on the Mount bracket should face the camera onitoring area.
Adjusting the camera direction
Ceiling mount opener
1.Press the Locker button on the bottom of your camera and remove the Cover dome
from the Main body using the other hand. The Main body and Inner cover will be
exposed to you.
2.To install and adjust your camera, you have to first remove the Inner cover. To
remove the Inner cover from the Main body, push a long thin screwdriver into the
narrow spot of the Wing locker and press it outward to remove the cover.
3.Remove the Mount bracket from the Main body by rotating the Main body in the
UNLOCK direction while pushing the Lock releaser out ward. If it is not easily
done, rotate the Mount bracket in the LOCK direction while holding small holes
on the Mount bracket.
4.Fix the Mount bracket to the location (ceiling or wall) with supplied three screws.
To install your camera
Tech. Specifications
When the camera is fixed on the ceiling, you
can adjust the camera viewing angle. You can
rotate your camera leftward or rightward
(Panning), and can change the slope of your
camera upward or down ward (Tilting).
In case of panning, the rotation limit of your
camera is set to 355 degree (100 degree
clockwise and 255 degree counterclockwise).
The rotation is stopped by the Stopper inside
of the camera. For panning control, first
unfasten two screws located on the bottom and
In case of tilting, you can change the slope of your camera from zero to 90 degree.
However if the slope angle is under 17 degree, you can encounter a partial image hide
problem. To fix the location after adjusting the tilting angle, use the Tilt fixing screws.
To adjust the focus and zoom of your camera, use the Zoom lever and Focus lever.
When you install the camera on the inclined ceiling or wall, you can rotate the camera
lens to see a correct direction image.
rotate in the direction you want, and then fasten them to fix the camera.
Sensor
TV system
Sync mode
Resolution
S/N Ratio
Minimum
illumination
BLC
AES
Mirror
Power Supply Voltage
Power current
Lens
1/3" High Sensitivity CCD
PAL/NTSC
Internal
52dB(AGC OFF)
OFF/NO
OFF/NO
OFF/NO
DC12V
Without IR
With IR:<230mA(DC12V)
:<100mA(DC12V)
4-9mm
-10 C to 50 C (Within85%RH)
Operation Temperature
-20 C to 50 C (Within85%RH)
Operation Humidity
3-Axis
DNR
IR range Without IR(NO); With IR(20M)
91mm(H) ╳ 128mm(D)
Size(mm)
0TVL
Without IR
With IR
0.01Lux
0Lux (IR ON)
OFF/NO
Gain Control
372g
Weight
Model
