Sears Kenmore 85230 Manual de servicio

MICROWAVE OVEN

INSTALLATION

INSTRUCTION

MANUAL

MODEL No.

85230

85238

85239

85240

85248

85249

Read and save these

installation instructions.

INSTALLATION

INSTRUCTIONS

*Sold by Sears Canada Inc. Printed in Korea

Part No. 3828W5U0257 SEARS. CANADA INC., TORONTO. M5B 2B8

YOUR SAFETY FIRST

BEFORE YOU START

• Proper installation is the installer's responsibility!

– Read the entire manual before you begin. The Model number label is located on the oven front.

See Figure 1. Mounting plate is located on back side of microwave oven. See Figure 2.

BE SURE TO READ THE FOLLOWING SAFETY INSTRUCTIONS:

FOR YOUR SAFETY:

• You will need TWO people to install this oven. It is heavy and could cause personal injury if not handled

properly. The dimensions of the oven are as follows:

Height : 16 7/16 inches

Width : 29 15/16 inches

Depth : 15 5/8inches

Weight : 60 lbs.

• Avoid Electrical Shock!

– Before you drill into the wall, note where electrical outlets are and where electrical wires might be concealed

behind the wall. YOU COULD GET AN ELECTRIC SHOCK if you contact electrical wires

with your drill bit.

– Locate and disconnect the power to any electrical circuits that could be affected by installing this oven.

IF YOU DO NOT DISCONNECT THE POWER, YOU COULD GET AN ELECTRIC SHOCK.

• ELECTRICAL RATING OF THIS OVEN : 120V AC 60Hz.

13 Amp / 1,500 W (Microwave oven + Cooktop Lamps + Ventilation Fan)

– You need a DEDICATED 120V, 60Hz, AC only, 15 or 20A, fused electrical supply (located in the cabinet

above the microwave as close as possible to the microwave) serving only the microwave.

— 2 —

Mounting

plate

( Remove from

oven to install. )

Back of oven

Figure 1 Figure 2

Model Number Label

W A R N I N G

• THIS APPLIANCE MUST BE GROUNDED!

– If there is an electrical short circuit, grounding reduces the risk of electrical shock by providing an escape

wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding

plug.

• Place the plug into a properly installed and grounded outlet. See Figure 3.

• Do not use an extension cord.

• Keep the power cord dry and do not pinch or crush it.

• DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE

POWER SUPPLY CORD GROUNDING PRONG!

This appliance MUST be grounded!

If you use the grounding plug improperly, you risk electric shock!

– Check with a qualified electrician if you are not sure whether the oven is properly grounded or if you do not

completely understand the grounding instructions.

DO NOT USE A FUSE IN THE NEUTRAL OR GROUNDING CIRCUIT.

Improper grounding could result in electric shock or other personal injury.

SAVE THESE INSTRUCTIONS FOR THE LOCAL ELECTRICAL INSPECTOR'S USE.

• DO NOT EXPOSE YOURSELF TO EXCESSIVE MICROWAVE ENERGY!

– DO NOT try to operate the microwave oven with the door open.

– DO NOT tamper with or defeat the safety interlocks.

– DO NOT place objects between the microwave oven front face and the door.

–

DO NOT allow soil or cleaner residue to build up on the flat surfaces around the microwave oven door.

– DO NOT operate the microwave oven if it is damaged.

– The microwave oven door must close properly to operate safely.

– DO NOT USE THE MICROWAVE OVEN:

• If the door is bent.

• If the hinges or latches are broken or loose.

• If the door seals, sealing surfaces or glass is broken.

– DO NOT ATTEMPT TO ADJUST OR REPAIR THE OVEN YOURSELF!

It should be adjusted and repaired by a qualified technician who can check for microwave leakage after

repairing the oven.

If you do not use the microwave oven as instructed,

you could be exposed to excessive microwave energy.

YOUR SAFETY FIRST

— 3 —

PROPERLY POLARIZED AND

GROUNDED OUTLET

Three-Pronged (Grounding) Plug

Figure 3

W A R N I N G

• MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT.

–Mount the oven against a flat, vertical wall, so it is supported by the wall. The wall should be constructed of

minimum 2" x 4" wood studding and 3/8" thick drywall or plaster/lath.

–ATTACH AT LEAST ONE of the two lag screws supporting the oven to a vertical, 2" x 4" wall stud.

–DO NOT mount the microwave oven to an island or peninsula cabinet.

–BE SURE the upper cabinet and rear wall structures are able to support 150 lbs., plus the weight of any

items you place inside the oven or upper cabinet.

–Locate the oven away from strong draft areas, such as windows, doors, and strong heating vents.

–BE SURE you have enough space. See Figure 4 below for minimum vertical and horizontal clearance.

If you do not mount the oven as instructed,

you risk personal injury and/or property damage.

CAUTION

• Before you begin installing the oven, PLACE A PIECE OF THE CARTON OR OTHER HEAVY

MATERIAL (a blanket) over the countertop or cooktop to protect it. Do not use a plastic cover.

Failure to protect these surfaces could result in property damage.

YOUR SAFETY FIRST

—4 —

30" min. cabinet opening width

30" min. clearance from bottom

of cabinet to coo ing surface

or countertop

(Use templates included

with installation instructions)

Grounded Outlet

(inside upper cabinet)

Power Supply Cord Hole

Figure 4

W A R N I N G

THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN:

NOTE: Depending on your ventilation requirements, you may not use all of these parts.

NOTE: You need to install at least one lag screw into a 2" x 4" stud and four anchor bolts into the wall.

The mounting area must meet the 150 lbs. weight requirement.

—5 —

Damper/duct connector

(for roof-venting or wall-venting installation)

Not Actual Size

One power cord clamp and

One dar -colored mounting screw

(to old t e power cord)

Actual Size

Two tapping screws - Actual Size

(for attac ing t e damper duct connector)

Four 1/4" x 2" lag screws - Actual Size

(for wall stud oles)

Two 1/4" x 2" bolts - Actual Size

(for securing to t e upper cabinet) Four spring toggle heads - Actual Size

(for t e toggle bolts)

Two washers - Actual Size

(for t e two upper cabinet bolts)

Four 1/4" x 3" toggle bolts - Actual Size

(for drywall oles)

One power cord clamp bushing - Actual Size

(for t e cord ole in a metal upper cabinet)

One loc pin and one washer-Not Actual size

PARTS, TOOLS, MATERIALS

YOU WILL NEED THE FOLLOWING TOOLS AND MATERIALS FOR THE INSTALLATION:

Carton or other heavy material for covering the counter top.

• If you have brick or masonry walls, you will need special hardware and tools.

• The ductwork you need for the installation is not included. All wall and roof caps must have a back-draft

damper.(Shown on page 5.)

PARTS, TOOLS, MATERIALS

—6 —

Clear tape

(for taping the templates to the wall) Stud finder or thin nail.

Saber saw (for cutting vent

holes for roof or wall venting)

Keyhole saw (for the power cord hole)

Electric drill

3/8" and 3/4" wood drill bits

1/2" and 3/16"

drill bits

Phillips screwdriver (for the screws)

Pencil

Flat blade screwdriver (for the toggle bolts)

Measuring tape (metal preferred)

Small side cutters or tin snips Caulking gun

Plumb line

Duct Tape

AVOID ELECTRICAL SHOCK! THIS APPLIANCE MUST BE GROUNDED!

1. Locate the grounded electric outlet for this oven in the cabinet

above the oven, as shown in Figure 4.

NOTE: The outlet should be on a circuit dedicated to the

microwave oven 120V, 60Hz., AC only with a

20A fused electrical supply.

IMPORTANT: If you do not have the proper wall outlet, you MUST

have one installed by a qualified electrician.

2. You will cut the power-supply-cord hole (shown in

Figure 4) later when you prepare the wall and upper cabinet in

Step 4.

NOTE: Do not use an extension cord.

Keep the power cord dry and do not pinch or crush it.

Improper grounding could result in

electric shock or other personal injury.

• DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE POWER SUPPLY

CORD GROUNDING PRONG! This appliance MUST be grounded!

STEP 1: PREPARE THE

ELECTRICAL CONNECTIONS

—7 —

Grounded Outlet

( Inside Cabinet )

Upper

Cabinet

Power-Supply-Cord Hole

Figure 4

W A R N I N G

NOTE: The ductwork you need for outside ventilation is not included with your oven. The standard ductwork

fittings and length are shown in Figure 9, page 9.

THIS OVEN MUST BE PROPERLY VENTED!

You may vent your oven in one of three ways:

Roof-venting If your oven is located on an outside wall near the roof, as in Figures 6 (31/4" x

10" duct) and 8 (6" round duct.)

Wall-venting If your oven is located on an outside wall on the first floor of your house, as in Figure

5 (31/4" x 10" duct) and Figure 8 (6" round duct.)

Room-venting If your oven is located on an inside wall of your house, as in Figure 7.

NOTE: If you choose the rear exhaust method (roof-or wall-venting), be sure there is enough clearance within

the wall for the exhaust duct.

REMEMBER AS YOU INSTALL THE VENTING:

• Keep the length of the ductwork and the

number of elbows to a minimum to

ventilate your oven efficiently.

See examples on page 9.

• Keep the size of the ductwork the same.

• Do not install two elbows together.

• Use duct tape to seal all joints in the duct

system.

• Use caulking to seal the exterior wall or

roof opening around the cap.

STEP 2:

PREPARE THE VENTING SYSTEM

—8 —

Wall Venting

Wall venting

t roug -t e-wall

wall cap

3 1/4"x10"

duct

Figure 5

cabinet

oven

Roof Venting

t roug -t e-roof

3 1/4"x10"

duct

Figure 6

roof cap

Roof venting

cabinet

oven

6" min.

diameter

round duct

3 1/4" to round

duct transition

3 1/4" to round

ductwork transition

Figure 8

roof cap

wall cap

elbow

W A R N I N G -F I R E H A Z A R D

Room Venting

Figure 7

cabinet

oven

STEP 2:

PREPARE THE VENTING SYSYTEM

STANDARD FITTINGS

NOTE: If the existing duct is round, you must use a rectangular-to-round adapter, with a rectangular 3"

extension duct installed between the damper assembly and the adapter to prevent the exhaust

damper’s sticking.

DUCT LENGTH

The total length of the duct system, including straight duct, elbows, transitions, wall or roof caps must not

exceed the equivalent of 140 feet.

For best performance, do not use more than three 90 degree elbows.

Below are the standard fittings and their equivalent length in feet.

To calculate the equivalent length of each ductpiece used, see the examples below.

—9 —

Figure 9

1

4567

2 3

3 1/4"x10"

to 6"=5ft.

90˚ elbow

=10ft. 45˚ elbow

=5ft.

3 1/4"x10"

wall cap

=40ft.

3 1/4"x10"

flat elbow

=10ft.

3 1/4"x10" roof

cap=24ft. 3 1/4"x10" 90˚

elbow=25ft.

Examples

For 3 1/4"x10" SYSTEMS

1-3 1/4" x 10" 90˚elbow

1-Wall Cap

8 feet straight duct

TOTAL LENGTH

1-transition

2-90˚elbows

1-Wall Cap

8 feet straight

TOTAL LENGTH

For 6" ROUND SYSTEMS

6ft.

2ft. 2ft.

3 1/4"x10"

90˚elbow wall cap 6ft.

90˚elbows

transition

wall cap

= 25 ft.

= 40 ft.

= 8 ft.

= 73 ft.

= 5 ft.

= 20 ft.

= 40 ft.

= 8 ft.

= 73 ft.

Your microwave oven is shipped with the blower assembled for roof venting. You need to adjust the blower if

you want wall-venting or room-vented (recirculating) installation.

ELECTRICAL SHOCK HAZARD! UNPLUG UNIT BEFORE WORKING ON IT.

• DO NOT PULL OR STRETCH THE BLOWER WIRING! Pulling and stretching the blower wiring could result in

electrical shock.

REMOVE THE MOUNTING PLATE:

1. Remove any shipping materials and parts from inside

the microwave oven.

2. Cover the counter top or cooktop with a thick,

protective covering to protect it from damage and

dirt. See Figure 10.

NOTE: If you have a free-standing range, disconnect

it, move it onto a piece of cardboard or

hardboard and pull it away from the wall, so

that you can get closer to the upper cabinet

and back wall for easier measuring and

drilling.

3. Remove mounting plate screw(s) (1 or 2 screws)

from the mounting plate as shown and discard.

(See Figure 11.)

4. This plate will be used as the rear mounting plate.

(It will be used to locate and mark the mounting

holes on the rear wall.)

5. Locate exhaust adaptor, grease filters and hardware

packet.

6. At this point, remove any adhesive tape (if there is

any), on the exhaust adaptor, the grease filters and

the power supply cord.

ROOF-VENTED INSTALLATION:

This oven is shipped assembled for roof-vented. You

will need to install the exhaust adaptor regardless of

cabinet.

1. Attach the exhaust adaptor to the blower plate by

sliding it into the guides. (See Figure 12.)

STEP 3:

PREPARE THE VENTING BLOWER

—10 —

Figure 10

A t ick, protective

covering

Figure 11

Mounting

plate

Mounting plate

screw(s)

(1 or 2 screws)

Control panel side

Figure 12

Back

of oven

Ex aust

adaptor

W A R N I N G

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Microondas de Sears

Sears

Sears 721.62212200 Guía de instalación

Sears

Sears 27" Wall Oven Manual de usuario

Sears

Sears 669933 - 1.1 cu. ft. Countertop Microwave Manual de usuario

Sears

Sears 721.67902600 Manual de usuario

Sears

Sears 721.66312500 Guía de instalación

Sears

Sears 721.80522500 Manual de usuario

Sears

Sears 721.80513 Manual de usuario

Sears

Sears Kenmore ELITE 65.69642 Manual de usuario

Sears

Sears 721.62222300 Manual de usuario

Sears

Sears Galaxy 85030 Manual de servicio

Sears

Sears 721.62252200 Manual de usuario

Sears

Sears Kenmore TOAST N WAVE MD-0942KT Manual de usuario

Sears

Sears 721.81622600 Manual de usuario

Sears

Sears 721.88502800 Manual de usuario

Sears

Sears 721.66102500 Manual de usuario

Sears

Sears 721.80412500 Guía de instalación

Sears

Sears Division 20 721.62102200 Manual de usuario

Sears

Sears 721.88512900 Manual de usuario

Sears

Sears 721.80042 Guía de instalación

Sears

Sears 565.60586000 Manual de usuario

Sears

Sears 721.66462500 Manual de usuario

Sears

Sears 721.80402400 Manual de usuario

Sears

Sears 721.62002200 Guía de instalación

Sears

Sears 721.64282300 Manual de usuario

Manuales populares de Microondas de otras marcas

Daewoo

Daewoo KOG-574R0S Manual de usuario

LG MH7040SS Manual de usuario

Sharp

Sharp R-895(AL)M Manual de usuario

Dometic

Dometic DOTRM13W Manual de usuario

Sanyo

Sanyo EM-X680 Manual de usuario

Sharp

Sharp R-393M Manual de usuario

KitchenAid

KitchenAid KMCX4510 Instrucciones de instalación

Smeg

Smeg S45MCX1 Manual de usuario

Russell Hobbs

Russell Hobbs RHM2044 Manual de usuario

Sunbeam

Sunbeam SMW759 Manual de usuario

Gallet

Gallet FMOE230S Manual de usuario

Bosch

Bosch CEG732X.1B Manual de usuario

Dometic

Dometic Roadmate 230 Manual de usuario

Samsung

Samsung SJ0396W Manual de usuario

Sanyo

Sanyo EM-P494WS Manual de usuario

Sharp

Sharp R-240 Manual de usuario

Electrolux

Electrolux EMS2840 Manual de usuario

Daewoo

Daewoo KOC-984T2S13 Manual de usuario