Sears Galaxy 85030 Manual de servicio

MICROWAVE OVEN

INSTALLATION

INSTRUCTION

MANUAL

MODEL No.

85030

85040

Read and save these

installation instructions.

INSTALLATION

INSTRUCTIONS

*Sold by Sears Canada Inc. Printed in Korea

Part No. 3828W5U0211 SEARS. CANADA INC., TORONTO. M5B 2B8

BEFORE YOU START

●Proper installation is the installer's responsibility!

– Read the entire manual before you begin. The Model number label is located on the oven front.

See Figure 1. Mounting plate is located on back side of microwave oven. See Figure 2.

BE SURE TO READ THE FOLLOWING SAFETY INSTRUCTIONS:

FOR YOUR SAFETY:

●You will need TWO people to install this oven. It is heavy and could cause personal injury if not handled

properly. The dimensions of the oven are as follows:

Height : 16 7/16 inches

Width : 29 15/16 inches

Depth : 15 3/8inches

Weight : 58 pounds

●Avoid Electrical Shock!

– Before you drill into the wall, note where electrical outlets are and where electrical wires might be behind

concealed the wall, YOU COULD GET AN ELECTRIC SHOCK it you contact electrical wires with your

drill bit.

– Locate and disconnect the power of any electrical circuits that could be affected by installing this oven.

IF YOU DO NOT DISCONNECT THE POWER, YOU COULD GET AN ELECTRIC SHOCK.

●ELECTRICAL RATING OF THIS OVEN : 120V AC. 60Hz.

13 Amps / 1500 Watts (Microwave oven + Cooktop Lamp + Ventilation Fan)

– You need a 120V, 60Hz, AC only, 15A or 20A, fused electrical supply (located in the cabinet above the

microwave as close as possible to the microwave circuit) serving only the microwave.

YOUR SAFETY FIRST

— 2 —

Model Number Label

Figure 1

Mounting

plate

(Remove from

oven to install.)

Back of oven

Figure 2

W A R N I N G

● THIS APPLIANCE MUST BE GROUNDED!

–If there is an electrical short circuit, grounding reduces the risk of electrical shock by providing an escape

wire for the electric current. This appliance is equipped with a cord having a grounding wire with a

grounding plug.

●Place the plug into a properly installed and grounded outlet. See Figure 3.

●Do not use an extension cord.

●Keep the power cord dry and do not pinch or crush it.

● DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE

POWER SUPPLY CORD GROUNDING PRONG!

This appliance MUST be grounded!

If you use the grounding plug improperly, you risk electric shock!

–Check with a qualified electrician if you are not sure whether the oven is properly grounded or if you do

not completely understand the grounding instructions.

DO NOT USE A FUSE IN THE NEUTRAL OR GROUNDING CIRCUIT.

Improper grounding could result in electric shock or other personal injury.

SAVE THESE INSTRUCTIONS FOR THE LOCAL ELECTRICAL INSPECTOR'S USE.

● DO NOT EXPOSE YOURSELF TO EXCESSIVE MICROWAVE ENERGY!

–DO NOT try to operate the microwave oven with the door open.

–DO NOT tamper with or defeat the safety interlocks.

–DO NOT place objects between the microwave oven front face and the door.

–

DO NOT allow soil or cleaner residue to build up on the flat surfaces around the microwave oven door.

–DO NOT operate the microwave oven if it is damaged.

–The microwave oven door must close properly to operate safely.

–DO NOT USE THE MICROWAVE OVEN:

●If the door is bent.

●If the hinges or latches are broken or loose.

●If the door seals, sealing surfaces or glass is broken.

–DO NOT ATTEMPT TO ADJUST OR REPAIR THE OVEN YOURSELF!

It should be adjusted and repaired by a qualified technician who can check for microwave leakage

after repairing the oven.

If you do not use the microwave oven as instructed, you could

be exposed to excessive microwave energy.

YOUR SAFETY FIRST

—3 —

PROPERLY POLARIZED AND

GROUNDED OUTLET

Three-Pronged (Grounding) plug

Figure 3

W A R N I N G

● MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT.

–Mount the oven against a flat, vertical wall, so that it is supported by the wall. The wall should be

constructed of minimum 2" x 4" wood studding and 3/8" thick drywall or plaster/lath.

–ATTACH AT LEAST ONE of the two lag screws supporting the oven to a vertical, 2" x 4" wall stud.

–DO NOT mount the microwave oven to an island or peninsula cabinet.

–BE SURE the upper cabinet and rear wall structures are able to support 150 lbs., plus the weight of any

items you place inside the oven or upper cabinet.

–Locate the oven away from strong draft areas, such as windows, doors, and strong heating vents.

–BE SURE you have enough space. See Figure 4 below for minimum vertical and horizontal clearance.

If you do not mount the oven as instructed,

you risk personal injury and/or property damage.

C A U T I O N

● Before you begin installing the oven, PLACE APIECE OF THE CARTON OR OTHER HEAVY

MATERIAL (a blanket) over the countertop or cooktop to protect it. Do not use a plastic cover.

Failure to protect these surfaces could result inproperty damage.

YOUR SAFETY FIRST

—4 —

30" min. cabinet opening width

30" min. clearance from bottom

of cabinet to cooking surface

or countertop

(Use templates included

with installation instructions)

Grounded Plug

(inside upper cabinet)

Power Supply

Cord Hole

Figure 4

W A R N I N G

THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN:

NOTE: Depending on your ventilation requirements, you may not use all of these parts.

NOTE: You need to install at least one lag screw into a 2" x 4" stud and four anchor bolts into the wall and

the mounting area must meet the 150 lbs. weight requirement.

PARTS, TOOLS, MATERIALS

—5 —

Damper/duct connector

(for roof-venting or wall-venting installation)

Not Actual Size

One power cord clamp and

One dark-colored mounting screw

(to hold the power cord)

Actual Size

Two tapping screws - Actual Size

(for attaching the damper duct connector)

Four 1/4" x 2" lag screws - Actual Size

(for wall stud holes)

Two 1/4" x 2" bolts - Actual Size

(for securing to the upper cabinet) Four spring toggle heads - Actual Size

(for the toggle bolts)

Two washers - Actual Size

(for the two upper cabinet bolts)

Four 1/4" x 3" toggle bolts - Actual Size

(for drywall holes)

One power cord clamp bushing - Actual Size

(for the cord hole in a metal upper cabinet)

One lock pin and one washer-Not Actual size

YOU WILL NEED THE FOLLOWING TOOLS AND MATERIALS FOR THE INSTALLATION:

Carton or other heavy material for covering the counter top.

● If you have brick or masonry walls, you need special hardware and tools.

● The ductwork you need for the installation is not included. All wall and roof caps must have a back-draft

damper.

PARTS, TOOLS, MATERIALS

—6 —

Clear tape

(for taping the templates to the wall) Stud finder or thin nail.

Saber saw (for cutting vent

hloes for roof or wall venting)

Key hole saw (for the power cord hole)

Electric drill

3/8" and 3/4" wood drill bits

1/2" and 3/16"

drill bits

Phillips screwdriver (for the screws)

Pencil

Flat blade screwdriver (for the bolts)

Measuring tape (metal preferred)

Small side cutters or tin snips Caulking gun

Plumb line

Duct Tape

AVOID ELECTRICAL SHOCK! THIS APPLIANCE MUST BE GROUNDED!

1. Locate the grounded electric outlet for this oven in the

cabinet above the oven, as shown in Figure 4 Detail.

NOTE: The outlet should be on a circuit dedicated to the

microwave oven 120V, 60Hz., AC only, with a

20ampere fused electrical supply.

IMPORTANT: If you do not have the proper wall outlet, you

MUST have one installed by a qualified

electrician.

2. You will cut the power-supply-cord hole (shown in

Figure 4 Detail) later when you prepare the wall and

upper cabinet in Step 4.

NOTE: Do not use an extension cord.

Keep the power cord dry and do not pinch or

crush it.

Improper grounding could result in

electric shock or other personal injury.

● DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE POWER

SUPPLY CORD GROUNDING PRONG! This appliance MUST be

grounded!

STEP 1: PREPARE THE

ELECTRICAL CONNECTIONS

—7 —

Grounded Outlet

Upper

Cabinet

Power-Supply-Cord Hole

Figure 4 Detail

W A R N I N G

NOTE: The ductwork you need for outside ventilation is not included with your oven. The standard

ductwork fittings and length are shown in Figure 9, page 9.

THIS OVEN MUST BE PROPERLY VENTED!

You may vent your oven in one of three ways:

Roof-venting If your oven is located on an outside wall near the roof, as in Figures 6 (31/4" x

10" duct) and 8 (6" round duct.)

Wall-venting If your oven is located on an outside wall on the first floor of your house, as in

Figures 5 (3 1/4" x 10" duct) and 8 (6" round duct.)

Room-venting If your oven is located on an inside wall of your house, as in Figure 7.

NOTE: If you choose the rear exhaust method (roof-or wall-venting), be sure there is enough clearance

within the wall for the exhaust duct.

REMEMBER AS YOU INSTALL THE

VENTING:

● Keep the length of the ductwork and the

number of elbows to a minimum to

ventilate your oven efficiently.

See examples on page 9.

● Keep the size of the ductwork the same.

● Do not install two elbows together.

● Use duct tape to seal all joints in the duct

system.

● Use caulking to seal the exterior wall or

roof opening around the cap.

STEP 2:

PREPARE THE VENTING SYSTEM

—8 —

Wall Venting

Wall venting through-the-wall

wall cap

3 1/4"x10"

duct

Figure 5

cabinet

oven

Roof Venting

through-the-roof

3 1/4"x10"

duct

Figure 6

roof cap

Roof venting

cabinet

oven

6" min.

diameter

round duct

3 1/4" to round

duct transition 3 1/4" to round

ductwork transition

Figure 8

roof cap

wall cap

elbow

W A R N I N G -F I R E H A Z A R D

Room Venting

Figure 7

cabinet

oven

STANDARD FITTINGS

NOTE: If the existing duct is round, you must use a rectangular-to-round adapter, with a rectangular 3"

extension duct installed between the damper assembly and the adapter to prevent the exhaust

damper sticking.

DUCT LENGTH

The total length of the duct system, including straight duct, elbows, transitions, wall or roof caps must not

exceed the equivalent of 140 feet.

For best performance, do not use more than three 90 degree elbows.

Below are the standard fittings and their equivalent length in feet.

To calculate the equivalent length of each duct piece used, see the examples below.

STEP 2:

PREPARE THE VENTING SYSYTEM

—9 —

Figure 9

4567

3 1/4"x10"

to 6"=5ft.

90˚elbow

=10ft. 45˚elbow

=5ft.

3 1/4"x10"

wall cap

=40ft.

3 1/4"x10"

flat elbow

=10ft.

3 1/4"x10" roof

cap=24ft. 3 1/4"x10" 90˚

elbow=25ft.

Examples

For 3 1/4"x10" SYSTEMS

1-3 1/4" x 10" 90˚elbow

1-Wall Cap

8 feet straight duct

TOTAL LENGTH

1-transition

2-90˚elbows

1-Wall Cap

8 feet straight

TOTAL LENGTH

For 6" ROUND SYSTEMS

6ft.

2ft. 2ft.

3 1/4"x10"

90˚elbow wall cap 6ft.

90˚elbows

transition

wall cap

= 25 ft.

= 40 ft.

= 8 ft.

= 73 ft.

= 5 ft.

= 20 ft.

= 40 ft.

= 8 ft.

= 73 ft.

Your microwave oven is shipped with the blower assembled for roof venting. You need to adjust the blower if

you want wall-venting or room-vented (recirculating) installation.

ELECTRICAL SHOCK HAZARD!

UNPLUG UNIT BEFORE WORKING ON IT.

● DO NOT PULL OR STRETCH THE BLOWER WIRING! Pulling and stretching the blower wiring

could result in electrical shock.

STEP 3:

PREPARE THE VENTING BLOWER

—10 —

Figure 10

Figure 11

Figure 12

Figure 14

Figure 13

Mounting plate

Mounting plate screws

Control panel side

blower unit

Parts "B"

back plate

Knockouts Parts "B"

Parts "B"

back Plate

blower

unit

exhaust

ports

back plate

Damper

Exhaust

adaptor

Tapping screw

(Bright color)

blower plate

blower unit

mounting screw

blower plate

mounting screws

W A R N I N G

Remove two screws that attach mounting plate to

microwave oven cabinet. See Figure 10.

Remove mounting plate and set aside. Replace the screws.

ROOF-VENTED INSTALLATION:

1. Insert one side of exhaust adaptor and attach with

the one tapping screw on the other side of exhaust

adaptor to the blower plate. See Figure 11.

Go to STEP 4 on page 12.

WALL-VENTED INSTALLATION:

1. Remove one blower unit mounting screw and two blower

plate screws. Remove the blower plate from cabinet.

See Figure 12.

2. Carefully lift the blower unit out of the microwave oven.

3. Use side cutters or tin snips to cut and remove knockouts

parts “B”from Back plate. Discard knockouts.

Be careful not to distort the plate. See Figure 13.

4. Rotate the unit so that the exhaust ports face the rear of

the cabinet. See Figure 14. When you insert blower unit,

blower wire must be like figure 14.

5. Place blower unit back into cabinet. Check that the

exhaust ports face towards the rear of the cabinet.

See Figure 15.

6. Reattach the blower plate to cabinet so the

exhaust ports and blower plate opening are aligned.

Attach with one blower unit mounting screw and

then two blower plate mounting screws.

See Figure 16.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Microondas de Sears

Sears

Sears Division 20 721.62102200 Manual de usuario

Sears

Sears 721.62002200 Guía de instalación

Sears

Sears 721.62222300 Manual de usuario

Sears

Sears 721.80402400 Manual de usuario

Sears

Sears 721.67902600 Manual de usuario

Sears

Sears 721.69252990 Guía de instalación

Sears

Sears 721.80412500 Guía de instalación

Sears

Sears 721.81622600 Manual de usuario

Sears

Sears 721.66292500 Manual de usuario

Sears

Sears 27" Wall Oven Manual de usuario

Sears

Sears 721.62342200 Manual de usuario

Sears

Sears 721.62252200 Manual de usuario

Sears

Sears 721.80042 Guía de instalación

Sears

Sears 721. 63762 Manual de usuario

Sears

Sears 721.60102000 Guía de instalación

Sears

Sears 721.80802400 Manual de usuario

Sears

Sears Kenmore 89682 Manual de usuario

Sears

Sears Kenmore 721.69211 Manual de usuario

Sears

Sears Kenmore ELITE 665.63792 Manual de usuario

Sears

Sears 565.60586000 Manual de usuario

Sears

Sears 721.80513 Manual de usuario

Sears

Sears 721.66312500 Guía de instalación

Sears

Sears Galaxy 85000 Manual de usuario

Sears

Sears 721.62212200 Guía de instalación

Manuales populares de Microondas de otras marcas

Daewoo

Daewoo KOG-574R0S Manual de usuario

LG MH7040SS Manual de usuario

Sharp

Sharp R-895(AL)M Manual de usuario

Dometic

Dometic DOTRM13W Manual de usuario

Sanyo

Sanyo EM-X680 Manual de usuario

Sharp

Sharp R-393M Manual de usuario

KitchenAid

KitchenAid KMCX4510 Instrucciones de instalación

Smeg

Smeg S45MCX1 Manual de usuario

Russell Hobbs

Russell Hobbs RHM2044 Manual de usuario

Sunbeam

Sunbeam SMW759 Manual de usuario

Gallet

Gallet FMOE230S Manual de usuario

Bosch

Bosch CEG732X.1B Manual de usuario

Dometic

Dometic Roadmate 230 Manual de usuario

Samsung

Samsung SJ0396W Manual de usuario

Sanyo

Sanyo EM-P494WS Manual de usuario

Sharp

Sharp R-240 Manual de usuario

Electrolux

Electrolux EMS2840 Manual de usuario

Daewoo

Daewoo KOC-984T2S13 Manual de usuario