Sealey VSE9540 Manual de usuario
3/4” SQ. DRIVE REAR DIFFERENTIAL PINION
FLANGE TOOL - LAND ROVER FREELANDER II -
MODEL NO: VSE9540
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Wear approved eye protection. Wear appropriate Personal Protective Equipment. A full range of Personal Protective
Equipment is available from your Sealey stockist.
WARNING! Ensure that Health & Safety, Local Authority Regulations and general workshop practice Regulations are adhered to
when using tools.
8DO NOT use tools if damaged.
9Maintain tools to ensure that they are in an adequate condition for safe use and optimum performance.
9Ensure that a vehicle that has been raised by a jack is adequately supported. Use axle stands.
9Wear suitable clothing to avoid snagging. DO NOT wear jewellery. Tie back long hair.
9Account for all tools, parts and components being used. DO NOT leave these in or near the engine. Return tools to suitable
storage after use.
▲IMPORTANT! These Instructions are provided as a guide only. Always refer to the vehicle manufacturer’s service instructions or a
proprietary manual to establish the correct procedure and data.
WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations. The
Operator / user must apply caution and common sense (good practical sense).
9When timing an engine, always prevent the engine from being turned over. Use a notice and/or inhibit the engine.
WARNING! Incorrect or out of phase camshaft timing can result in contact between the valve head and the piston crown. This will
cause damage to the engine.
2. INTRODUCTION
Two piece kit essential for removal/installation of the pinion drive nut. Contains 12 sided pinion nut holding tool and splined socket. Suitable for
post 2006 Land Rover Freelander 2.
3. CONTENTS
4. APPLICATIONS
Models:
Land Rover Freelander II post 2006
Original Language Version
© Jack Sealey Limited
Refer to
Instructions
Wear eye
Protection
Item Part no. Description
1 VSE9540.01 12 sided holding tool
2 VSE9540.02 Deep splined socket
OE tools
JLR-205-984
VSE9540 Issue:1 29/10/19
5. OPERATION
5.1. Two-piece kit essential for removal/installation of the pinion drive nut on post 2006 Land Rover Freelander. Contains 12 sided pinion
nut holding tool and splined socket.
5.2. Refer to manufacturer’s instructions or a proprietary workshop manual for the correct torque settings and procedures for the repair
being performed.
5.3. REMOVAL
5.3.1. Locate the 12 sided holding tool on the pinion nut and ensure the lug is located against the differential casing appropriate to the
directionrequiredtoundotheangenut.
5.3.2. Insert the deep splined socket through the holding tool and locate onto the splined shaft, turn the deep splined socket in a clockwise
directiontoundotheangenut.
5.4. INSTALLATION
5.4.1. After the desired repair has been completed, locate the 12 sided holding tool on the pinion nut and ensure the lug is located against
thedifferentialcasingappropriatetothedirectionrequiredtoundotheangenut.
5.4.2. Insert the deep splined socket through the holding tool and locate onto the splined shaft, turn the deep splined socket in an anti-
clockwisedirectiontotightentheangenut.
Note: Tightening torques can be up to 250Nm, a suitable torque wrench such as the Sealey AK228 will be required.
Original Language Version
© Jack Sealey Limited
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
VSE9540 Issue:1 29/10/19
Tabla de contenidos
Otros manuales de Instrumento de medición de Sealey
Sealey
Sealey SA9302 Manual de usuario
Sealey
Sealey AK9621EV Manual de usuario
Sealey
Sealey PP7 Manual de usuario
Sealey
Sealey Auto Service Series Manual de usuario
Sealey
Sealey VSE5863 Manual de usuario
Sealey
Sealey AK9623EV Manual de usuario
Sealey
Sealey GA45 Manual de usuario
Sealey
Sealey VS0566 Manual de usuario
Sealey
Sealey VS0560.V2 Manual de usuario
Sealey
Sealey AUTO SERVICE VS0563 Manual de usuario
Sealey
Sealey PP5 Manual de usuario
Sealey
Sealey Auto Service VS8196.V2 Manual de usuario
Sealey
Sealey VS8196 Manual de usuario
Sealey
Sealey BT91/5.V3 Manual de usuario
Sealey
Sealey MM302.V2 Manual de usuario
Sealey
Sealey TA300 Manual de usuario
Sealey
Sealey GA70CR Manual de usuario
Sealey
Sealey TP101 Manual de usuario
Sealey
Sealey DBG506D Manual de usuario
Sealey
Sealey TA200.V2 Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario