Sealey SA9302 Manual de usuario

3.1 INSTALLATION FOR BOTH MODELS

3.1.1 AIR SUPPLY - MAXIMUM PRESSURE 12bar (175psi)

The supply must be clean and dry - use a suitable filter/water trap if necessary. The supply pressure at the gauge

inlet should ideally be 10bar (145psi).

Note: Maximum tyre inflation pressure cannot exceed the supply pressure.

1. SAFETY INSTRUCTIONS

3Disconnect the gauge from the air supply before changing accessories, servicing or performing any maintenance.

3Maintain the gauge in good condition (use an authorised service agent), and keep the gauge clean for best and safest

performance.

3Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate

the warranty.

3Locate gauge in a suitable work area, keep area clean and tidy and free from unrelated materials and ensure there is

adequate lighting.

3Keep children and unauthorised persons away from the work area.

7DO NOT direct gauge outlet at yourself or at other persons or animals.

7DO NOT carry by the hose, or yank the hose from the air supply.

7DO NOT use the gauge for a task which it is not designed to perform.

7DO NOT operate the gauge when you are tired or under the influence of alcohol, drugs or intoxicating medication.

7DO NOT operate gauge if parts are missing or the gauge is damaged, as this may cause failure and/or personal injury.

2. INTRODUCTION & SPECIFICATIONS

3. INSTALLATION

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS

PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL

INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS FOR FUTURE USE.

SA9302 & SA9312 - 1 - 091105

INSTRUCTIONS FOR:

PROFESSIONAL AIR LINE GAUGES

MODELS: SA9302 & SA9312

SA9302: Composite body and dial type gauge with rubber protector. Calibrated in bar/psi. Fitted with 500mm rubber hose

and single clip-on connector.

SA9312: Composite body and dial type gauge with rubber protector. Calibrated in bar/psi. Fitted with 500mm rubber hose

and a twin push-on connector.

SPECIFICATION. SA9302 SA9312

Range: 0-10bar (145psi). 0-10bar (145psi).

Air Supply Maximum: 12bar (175psi). 12bar (175psi).

Inlet: 1/4BSP Male. 1/4BSP Male.

Connector: Single clip. Twin push on.

Hose: 500mm rubber. 500mm rubber.

SA9312

SA9302

Clip-on Connector

Twin Push-on Connector

Operating Lever

Gauge

1/4BSP Male

5. MAINTENANCE & SERVICE

PERIODIC CHECKS AND MAINTENANCE

For long service and accuracy, the following actions should be carried out at the recommended intervals.

5.1 WEEKLY - CHECK OPERATION

The gauge should be checked weekly for correct operation. Look for smooth lever operation and fast, smooth gauge

movements. Check for leaks from tyre connector seals, and for chafing or wear of the flexible hoses. Any problems

should be immediately rectified.

5.2 QUARTERLY - CHECK CALIBRATION

We recommend the accuracy of the gauge be checked against a calibrated master gauge every 3 months, or at shorter

intervals depending on operators own quality procedures.

4. OPERATION

4.1 ATTACH ADAPTOR TO VALVE

Push and hold the connector onto the tyre valve using the most convenient side of the twin valve connector (SA9312).

For SA9302, squeeze the thumb clip on the connector, push the connector onto the tyre valve and release the clip.

The connector will now be locked in place.

4.2 TO INFLATE

Momentarily depress the operation lever fully, then release to display tyre pressure. When reading the pressure, hold the

gauge flat with respect to the eye to minimise error.

Fully depress operation lever for an appropriate period. Avoid over inflation, release lever frequently to check the pressure.

4.3 TO DEFLATE

Depress lever half-way (until air can be heard escaping) for an appropriate period. Fully depress lever momentarily then

release to display new pressure.

IMPORTANT - ALWAYS FULLY DEPRESS LEVER MOMENTARILY BEFORE READING TYRE PRESSURE.

SA9302 SA9312

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: No liability is accepted for incorrect use of these products.

WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

INFORMATION: For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.

sales@sealey.co.uk

www.sealey.co.uk

Web

01284 757500

01284 703534

Sole UK Distributor

Sealey Group,

Bury St. Edmunds, Suffolk.

SA9302 & SA9312 - 1 - 091105

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Sealey

Sealey

Sealey VS925.V2 Manual de usuario

Sealey

Sealey AK9635D.V2 Manual de usuario

Sealey

Sealey TP956.V2 Manual de usuario

Sealey

Sealey VS212.V3 Actualización de firmware

Sealey

Sealey AK9621EV Manual de usuario

Sealey

Sealey AK9623EV Manual de usuario

Sealey

Sealey GA70CR Manual de usuario

Sealey

Sealey TA060 Manual de usuario

Sealey

Sealey GA45 Manual de usuario

Sealey

Sealey RS125.V2 Manual de usuario

Sealey

Sealey GA450 Manual de usuario

Sealey

Sealey TA304 Manual de usuario

Sealey

Sealey VS0560.V2 Manual de usuario

Sealey

Sealey DBG5011 Manual de usuario

Sealey

Sealey MM405 Manual de usuario

Sealey

Sealey TA305 Manual de usuario

Sealey

Sealey PP5 Manual de usuario

Sealey

Sealey TA500 Manual de usuario

Sealey

Sealey MM405 Manual de usuario

Sealey

Sealey TA203.V2 Manual de usuario

Sealey

Sealey Auto Service Series Manual de usuario

Sealey

Sealey VS0052 Manual de usuario

Sealey

Sealey TA201 Manual de usuario

Sealey

Sealey TA200 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario