SeaLevel PIO-48 4030 Manual de usuario

PIO-48™

PART # 4030

USER MANUAL

Sections:

1. Installation

2. Address Selection

3. Options

4. Technical Description

5. Programming with the API

6. Specifications

7. Warranty

Figures:

1. Address Selection Table

2. Dip-Switch Illustration

3. J5 & J6 Illustration (IRQ Selection)

4. Silk-Screen

5. Schematic

6. Data Sheet

Sealevel Systems, Incorporated

155 Technology Place

P. O. Box 830

Liberty, SC 29657

(864) 843-4343 FAX (864) 843-3067

www.sealevel.com

SECTION 1. Installation

The PIO-48 can be installed in any of the PC expansion slots, except J8 on the original IBM

"XT" and Portable. Remove the PC case, remove the blank metal slot cover, and insert the

board. Replace the screw, replace the case, and the installation is complete.

Be sure to set the address and jumper options before installation.

SECTION 2. Address Selection

The PIO-48 occupies 8 consecutive I/O locations. Dip-switch SW1 sets the base address for

the PIO-48. Be careful when selecting the base address as some selections conflict with

existing PC ports. The following table shows several examples that usually do not cause a

conflict.

ADDRESS BINARY SWITCH POSITION SETTING:

Hex A9 A0 1234567

280-287 1010000XXX OFF ON OFF ON ON ON ON

2A0-2A7 1010100XXX OFF ON OFF ON OFF ON ON

2E8-2EF 1011101XXX OFF ON OFF OFF OFF ON OFF

2F8-2FF 1011111XXX OFF ON OFF OFF OFF OFF OFF

3E8-3EF 1111101XXX OFF OFF OFF OFF OFF ON OFF

300-307 1100000XXX OFF OFF ON ON ON ON ON

328-32F 1100101XXX OFF OFF ON ON OFF ON OFF

3F8-3FF 1111111XXX OFF OFF OFF OFF OFF OFF OFF

Typically COM1: = 3F8h; COM2: = 2F8h; COM3: = 3E8h; COM4: = 2E8h.

Figure 1

Address Selection Table

The following illustration shows the correlation between the dip-switch setting and the address

bits used to determine the base address. In the example below, the address 300 hex through

307 hex is selected. 300 HEX =11 0000 0XXX In binary representation.

1 2 3 4 5 6 7 8

Figure 2

Dip-Switch Illustration

NOTE: Setting the switch "On" or "Closed" corresponds to a "0" in the address, while

leaving it "Off" or "Open" corresponds to a "1".

SECTION 3. Options

Wait States

The PIO-48 has the option of inserting one 500 nS wait state for each access. This may be

required on certain machines with bus clocks in excess of 8 MHz. With the wide variety of

machines available, no concrete rules exist concerning wait states. If the PIO-48 doesn't

seem to be responding properly, try inserting a wait state.

To enable wait state insertion, set position 8 of the dip-switch to "ON". To disable wait states,

set position 8 "OFF".

Interrupts

The headers marked J5 and J6 allow the use of interrupts with the parallel ports. J5 selects

IRQ2 through IRQ7 for Port 1 (U9 and J1), while J6 selects the IRQ for Port 2 (U16 and J3).

Port 1

Port 2

Figure 3

J5 & J6 Interrupt Header ( Shown in Factory Default )

The interrupt input is available on the optional DB-37 cable connector at pin 1. This input is

active high, logic level 1, and must be enabled by pin 2, interrupt enable, which is active low,

or logic level 0. The enable line can be tied to ground if desired to always keep the interrupt

enabled. This implementation allows either positive or negative logic input to cause an IRQ to

be generated. Please contact Sealevel Systems Technical Support for further information.

The use of interrupts also requires special software to initialize the 8259 interrupt controller

and set the appropriate interrupt service routine vector, etc. Please refer to the IBM

Technical Reference Manual for more details.

SECTION 4. TECHNICAL DESCRIPTION

The PIO-48 utilizes two 8255 Parallel input/output (I/O) chips. Each chip provides three eight-

bit parallel I/O ports for a total of 48 I/O Lines. The ports within each 8255 are organized as

ports A, B, C, and D. For further information on the functionality of the 8255 refer to the 8255

data sheets at the end of this manual.

Ports A, B and C, can be input or output, meaning that they can be read (or input from), and

written (output) to. Port D is the Control Register, which determines whether ports A, B and

C are input or output. The Control Register sets the mode and direction for each port A, B,

and C. On power-on reset, the 8255 is reset and initialized with all 24 I/O lines as inputs. The

Control Register is normally written to at the beginning of a program, even if all ports are to be

input ports. I/O port offset addresses from Base Address (ex. 300 Hex)

8255 #1 (U9) PORT A 300 HEX 768 DECIMAL I/O PORT

PORT B 301 HEX 769 DECIMAL I/O PORT

PORT C 302 HEX 770 DECIMAL I/O PORT

PORT D 303 HEX 771 DECIMAL CONTROL REGISTER

8255 #2 (U16) PORT A 304 HEX 772 DECIMAL I/O PORT

PORT B 305 HEX 772 DECIMAL I/O PORT

PORT C 306 HEX 774 DECIMAL I/O PORT

PORT D 307 HEX 775 DECIMAL CONTROL REGISTER

Software Installation

For proper operation install software first. To install the software place the CD in

your CD-ROM tray and the auto-run program will start. If auto-run is not available,

browse the CD and choose “index.htm”. Choose Install Software at the beginning

of the CD. Select the Digital I/O software drivers and install SeaIO prior to

installing hardware.

Connectors

The PIO-48 provides two connectors for each port. The first connector (J1 and J3) is a 50 pin

header designed to mate with an optional ribbon cable to a solid state relay I/O module rack.

The second connector, (J2 and J4) is a 40 pin header that connects through an optional

ribbon cable to a DB-37 (male) connector that matches the pin-out of the Metrabyte™ PIO-12

board. These cables are available from Sealevel Systems.

Connector Pin-Out

PORT BIT J1, J3 50 PIN J2, J4 40 PIN DB-37 CABLE

PORT A

047 36 37

145 34 36

243 32 35

341 30 34

439 28 33

537 26 32

635 24 31

733 22 30

PORT B

031 19 10

129 17 9

227 15 8

325 13 7

423 11 6

521 95

619 74

717 53

PORT C

015 20 29

113 18 28

211 16 27

3914 26

4712 25

5510 24

63823

71622

Power, Ground and Interrupt Connections

Ground 2-50 4,21,25,29,33,37 11,13,15,17,19,21

Interrupt Input N/C 11

Interrupt Enable/ N/C 32

+5 Volts 49 2,35 20

-5 Volts N/C 23 12

+12 Volts N/C 31 16

-12 Volts N/C 27 14

Programming With The API

Application Programmers Interface (API)

Most modern operating systems do not allow direct hardware access. The

SeaIO driver and API have been included to provide control over the hardware

in Windows and Linux environments.

The purpose of this section of the manual is to help the customer with the

mapping of the API to the actual inputs for the 4030 specifically. Complete

documentation of the API can be found in its accompanying help file.

Interrupts:

Interrupt sampling can be set up in the API. Refer to the API section in the

SeaI/O help file for more detailed information.

Port C

Port C of each bank has the ability to be configured as two four bit ports. If

both lower and upper nibbles are configured the same then no special

considerations need to be made. But if they are configured differently, one

nibble as input, and one as output then the user will have to keep this in mind.

Port C absolute addressing (when port C is split)

When reading, the input nibble will be returned on the corresponding

upper or lower nibble while the outputs will be returned on their

corresponding upper or lower nibble. When writing, the corresponding

nibble will be written to the output nibble, while the input nibble will

have its output register written to. The output register can be written

to without affecting the inputs. These will be eight bit operations and it

will up to the programmer to keep track of the two four bit nibbles.

Port C relative addressing (when port C is split)

The input and output nibbles will each be treated as individual four bit

ports.

Port Configuration:

Each eight-bit port can be configured as inputs or outputs. The API provides a

set adapter state call to access the control words. For this device, two control

word is used. Refer to the following table.

Note: The control panel also allows youto configure the device. Your program

can over ride the control panel configuration when executed, but the control

panel configuration will be the default on power up. The default settings are

based on the settings in the control panel application when last changed and

saved after re-booting.

8255 Control Word 0: Bank 1 (A1, B1, C1)

8255 Control Word 1: Bank 2 (A2, B2, C2)

Relative Addressing vs. Absolute Addressing

The SeaIO API makes a distinction between “absolute” and “relative”

addressing modes. In absolute addressing mode, the Port argument to the API

function acts as a simple byte offset from the base I/O address of the device.

For instance, Port #0 refers to the I/O address base + 0; Port #1 refers to the

I/O address base + 1.

Relative addressing mode, on the other hand, refers to input and output ports in

a logical fashion. With a Port argument of 0 and an API function meant to

output data, the first (0th) output port on the device will be utilized. Likewise,

with a Port argument of 0 and an API function designed to input data, the first

(0th) input port of the device will be utilized.

In all addressing modes, port numbers are zero-indexed; that is, the first port is

port #0, the second port is #1, the third #2, and so on.

Tables : API Port/bit reference numbers for Absolute and Relative Addressing

R = Read

W = Write

R/W = Read or Write

Port API Port # Absolute Address

(function)

A1 0 ( R/W )

B1 1 ( R/W )

C1 2 ( R/W )

A2 4 ( R/W )

B2 5 ( R/W )

C2 6 ( R/W )

Absolute byte Address (any configuration)

Port API Port # Relative

Address (function) Port Type

A1 0 ( R ) Input

B1 1 ( R ) Input

C1 2 ( R ) Input

A2 0 ( W ) Output

B2 1 ( W ) Output

C2 2 ( W ) Output

Relative byte Address Given: Inputs A1, B1, C1,

Outputs A2, B2, C

SECTION 5. SPECIFICATIONS

Environmental Specifications

SPECIFICATION OPERATING STORAGE

Temperature Range 0 -50 Degrees C

32 -122 Degrees F -20 -70 Degrees C

-4-158 Degrees F

Humidity Range 10 -90% R.H.

Non Condensing 10 -90%

Non Condensing

Manufacturing Specifications

•IPC 610-A CLASS-III standards adhered to with a 0.1 visual A.Q.L. and 100% Functional

Testing.

•Boards are built to U.L. 94V0 rating and are 100% Electrically tested. Most boards are

solder mask over bare copper.

Power Specifications

Supply Line +5 +12 -12

Rating (mA) 200 mA 25 mA 25 mA

SECTION 6. Warranty

Sealevel Systems, Inc. provides a lifetime warranty for this

product. Should this product fail to be in good working order at

any time during this period, Sealevel Systems will, at it's option,

replace or repair it at no additional charge except as set forth in

the following terms. This warranty does not apply to products damaged by misuse,

modifications, accident or disaster.

Sealevel Systems assumes no liability for any damages, lost profits, lost savings or

any other incidental or consequential damage resulting from the use, misuse of, or

inability to use this product. Sealevel Systems will not be liable for any claim made

by any other related party.

Return authorization must be obtained from Sealevel Systems before returned

merchandise will be accepted. Authorization can be obtained by calling Sealevel

Systems and requesting a Return Merchandise Authorization (RMA) Number.

Sealevel Systems, Incorporated

155 Technology Place

P. O. Box 830

Liberty, SC 29657

(864) 843-4343 FAX (864) 843-3067

E-mail: [email protected]

Internet: www.sealevel.com

PIO-48™relay sensor interface is a trademark of Sealevel Systems, Incorporated.

IBM, "XT" and "AT" are trademarks of the International Business Machines Corporation.

Metrabyte™ and PIO-12™ are trademarks of Metrabyte Corporation.

Tabla de contenidos

Otros manuales de Hardware de computadora de SeaLevel

SeaLevel

SeaLevel SeaLINK +2.SC Manual de usuario

SeaLevel

SeaLevel SIO4-104.485 Manual de usuario

SeaLevel

SeaLevel COMM+16.PCIe Manual de usuario

SeaLevel

SeaLevel SIO-104 Manual de usuario

SeaLevel

SeaLevel DIO-16.LCPI Manual de usuario

SeaLevel

SeaLevel VERSA COMM +4 Manual de usuario

SeaLevel

SeaLevel Ultra-COMM+2/422.PCIe Manual de usuario

SeaLevel

SeaLevel SeaLINK+2/PC.SC Manual de usuario

SeaLevel

SeaLevel SeaLINK+16/USB Manual de usuario

SeaLevel

SeaLevel C4-104 Series Manual de usuario

SeaLevel

SeaLevel PLC-16.PCI Manual de usuario

SeaLevel

SeaLevel PROM-III Manual de usuario

SeaLevel

SeaLevel LATCH-16 Manual de usuario

SeaLevel

SeaLevel COMM+2 Manual de usuario

SeaLevel

SeaLevel DIO-16.PCI Manual de usuario

SeaLevel

SeaLevel ISO-16.PCI Manual de usuario

SeaLevel

SeaLevel ACB-II/EX Manual de usuario

SeaLevel

SeaLevel ACB II 3061 Manual de usuario

SeaLevel

SeaLevel SeaLINK+232.PC Manual de usuario

SeaLevel

SeaLevel SeaLINK/PC.SC Manual de usuario

SeaLevel

SeaLevel Relio Fanless Core 2 Duo R5200 Series Manual de usuario

SeaLevel

SeaLevel COMM+8.PC Manual de usuario

SeaLevel

SeaLevel SeaLINK+485-DB9 Manual de usuario

SeaLevel

SeaLevel 3547 Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario