Seagull Models SuperDave MX2 Manual de usuario

WWW.SEAGULLMODELS.COM

www.seagullmodels.com

Specications:

Wingspan---------------59.1 in (150 cm).

Wing area----------------632.4 sq.in (40.8 sq.dm).

Weight-------------------7.1 - 7.9 lbs (3.2 - 3.6 kg).

Length-------------------50.3 in (127.7cm).

Engine-------------------0.55cu.in--------2 stroke

----------------------------0.82cu.in--------4 stroke

----------------------------10cc gasoline.

Radio--------------------4 channel with 5 servos.

Electric power conversion.

ARF

ASSEMBLY MANUAL

“ Graphics and specications may change without notice “ .

MS: 208

SUPER DAVE MX2 Instruction Manual.

ankyouforchoosingtheSUPERDAVEMX2ARTFbySEAGULLMODELSCOMPANYLTD,.

e SUPER DAVE was designed with the intermediate/advanced sport yer in mind. It is a semi

scale airplane which is easy to y and quick to assemble. e airframe is onventionally built using

balsa, plywood to make it stronger than the average ARTF, yet the design allows the aeroplane to

be kept light. You will nd that most of the work has been done for you already. e motor mount

has been tted and the hinges are pre-installed. Flying the SUPER DAVE MX2 is simply a joy.

is instruction manual is designed to help you build a great ying earoplane. Please read

this manual throughly before starting assembly of your SUPER DAVE MX2. User the parts

listing below to indentify all parts.

INTRODUCTION.

WARNING.

KIT CONTENTS

Please be awere that this aeroplane is not a toy and if assemble or used incorrectly it is

capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU

ASSUME ALL RISK & REPONSIBILITY.

If you are inexperienced with basic RC ight we strongly recommend you contact your RC

supplier and join your local RC model Flying Club. RC Model Flying Clubs oer a variety of

training procedures designed to help the new pilot on his way to successful RC ight. ey

will also be able to advise on any insurance and safety regulations that may apply.

WWW.SEAGULLMODELS.COM

KIT CONTENTS.

ADDITIONAL ITEMS REQUIRED.

0.55 cu.in 2-stroke.

0.82 cu.in 4-stroke.

10cc gasoline engine.

Radio 4 channel with 5 servos.

Glow plug to suit engine.

Propeller to suit engine.

Protective foam rubber for radio

system.

TOOLS & SUPPLIES NEEDED.

ick cyanoacrylate glue.

30 minute epoxy.

5 minute epoxy.

Hand or electric drill.

Assorted drill bits.

Modelling knife.

Straight edge ruler.

2mm ball driver.

Phillips head screwdriver.

220 grit sandpaper.

90° square or builder’s triangle.

Wire cutters.

Masking tape & T-pins.

read-lock.

Paper towels.

HINGING THE AILERONS

SEA20801 Fuselage

SEA20802 Wing set

SEA20803 Tail set

SEA20804 Cowling

SEA20805 Canopy

SEA20806 Pilot

e control surfaces, including the

ailerons, elevators, and rudder, are

prehinged with hinges installed, but

the hinges are not glued in place. It is

imperative that you properly adhere

the hinges in place per the steps that

follow using a high-quality thin C/A

glue.

Note :

1) Carefully remove the aileron from one

of the wing panels. Note the position of the

hinges.

2) Remove each hinge from the wing panel

and aileron and place a T-pin in the center of

each hinge. Slide each hinge into the aileron

until the T-pin is snug against the aileron.

is will help ensure an equal amount of

hinge is on either side of the hinge line when

the aileron is mounted to the wing panel.

T-pin

Hinge.

3) Slide the aileron on the wing panel until

there is only a slight gap. e hinge is now

centered on the wing panel and aileron. Re-

move the T-pins and snug the aileron against

the wing panel. A gap of 1/64” or less should

be maintained between the wing panel and

aileron.

SUPER DAVE MX2 Instruction Manual.

4) Deect the aileron and completely

saturate each hinge with thin C/A glue. e

ailerons front surface shouldlightly contactthe

wing during this procedure. Ideally, when the

hinges are glued in place, a 1/64” gap or less

willbemaintainedthroughoutthelenghofthe

aileron to the wing panel hinge line.

Hinge.

e hinge is constructed of a special

material that allows the C/A to wick

or penetrate and distribute through-

out the hinge, securely bonding it to

the wood structure of the wing panel

and aileron.

Note :

Epoxy

5) Turn the wing panel over and deect the

aileron in the opposite direction from the

opposite side. Apply thin C/A glue to each

hinge, making sure that the C/A penetrates

into both the aileron and wing panel.

6) Using C/A remover/debonder and a pa-

per towel, remove any excess C/A glue that

may have accumulated on the wing or in the

aileron hinge area.

7) Repeat this process with the other wing

panel, securely hinging the aileron in place.

8) Aer both ailerons are securely hinged,

rmly grasp the wing panel and aileron to

make sure the hinges are securely glued and

cannot be pulled out. Do this by carefully ap-

plying medium pressure, trying to separate

the aileron from the wing panel. Use caution

not to crush the wing structure.

Work the aileron up and down sev-

eral times to “work in” the hinges

and check for proper movement.

Note :

HINGING THE ELEVATOR.

Glue the elevator hinges in place using the

same techniques used to hinge the ailerons.

WWW.SEAGULLMODELS.COM

HINGING THE RUDDER.

Glue the rudder hinges in place using the

same techniques used to hinge the ailerons.

INSTALL THE AILERONS CONTROL

HORN.

Locate the hardware necessary to install the

control horns for the ailerons.

Aileron Control Horn.

Epoxy

INSTALL ELEVATOR CONTROL HORN.

Install the elevator control horn using the

same method as same as the aileron control

horns.

Elevator Control Horn.

Epoxy

Elevator

Epoxy

INSTALL THE RUDDER CONTROL

HORN.

Repeat steps to install the rudder control

horn as same as steps done for ailerons.

SUPER DAVE MX2 Instruction Manual.

Rudder Control Horn.

Epoxy

Rudder Control Horn.

ENGINE MOUNT INSTALLATION.

1) Locate the items necessary to install the

engine mount included with your model.

2) Use four M4x30mm head bolts and four

4mm washers to attach the engine mount

rails to the rewall. Tighten the screws .

Make sure to use threadlock on the screws

to help prevent them from vibrating loose.

INSTALLING THE STOPPER

ASSEMBLY.

read locker glue

1) Using a modeling knife, carefully cut o

the rear portion of one of the 3 nylon tubes

leaving 1/2” protruding from the rear of the

stopper. is will be the fuel pick up tube.

2) Using a modeling knife, cut one length of

silicon fuel line. Connect one end of the line

to the weighted fuel pick up and the other

end to the nylon pick up tube.

M4x30mm

WWW.SEAGULLMODELS.COM

Vent tube. Fuel pick up tube.

Fuel fill tube.

3) Carefully bend the second nylon tube up

at a 45º angle. is tube is the vent tube.

4) Test t the stopper assembly into the tank.

It may be necessary to remove some of the

ashing around the tank opening using a

modeling knife. If ashing is present, make

sure none falls into the tank.

5) With the stopper assembly in place, the

weighted pick-up should rest away from the

rear of the tank and move freely inside the

tank. e top of the vent tube should rest just

below the top of the tank. It should not touch

the top of the tank.

6) When satised with the alignment of

the stopper assembly tighten the 3 x 20mm

machine screw until the rubber stopper ex-

pands and seals the tank opening. Do not

overtighten the assembly as this could cause

the tank to split.

FUEL TANK INSTALLATION.

You should mark which tube is the vent

and which is the fuel pickup when you attach

fuel tubing to the tubes in the stopper. Once

the tank is installed inside the fuselage, it

may be dicult to determine which is which.

7) Slide the fuel tank into the fuselage. Guide

the lines from the tank through the hole in

the rewall.

8) Use balsa plywood to help prevent move-

able from transferring to the fuel tank as

shown.

Fuel tank

Balsa

C/A glue

Fuel pick up.

Vent tube.

Fuel ll tube.

SUPER DAVE MX2 Instruction Manual.

INSTALLING THE MAIN LANDING

GEAR TO FUSELAGE.

1) e blind nuts for securing the landing

gear are already mounted inside the fuselage.

2) Using the hardware provided, mount the

main landing gear to the fuselage.

3) Place the fuselage inverted on the work-

bench in a suitable stand. Set the landing gear

in place and use a screwdrive to secure the

landing gear to the fuselage using bolts

M4x20mm and washers. Make sure to use

the threadlock on the bolts so they don’t vi-

brate loose.

M4x20mm

read locker glue.

M4x20mm

WHEEL AND WHEEL PANTS.

1) Locate the items neccessary to install.

2) Follow diagram below for wheel pant in-

stallation:

Use a drill and 8mm drill bit to drill a hole in

the wheel pants.

14mm.

8mm.

Drill a hole

3) You have to trim each axle using a tool

cutting and cut-o wheel.

4) Slide the collar to the axle and setscrew

the collars to secure the collar to the axle and

then slider the wheel on the axle with a drop

of oil on the axle so the wheel will spin freely

when installed. Prepare a second collar and

tighten the setscrew using hex wrench to se-

cure the collar to the axle.

5) Place the wheel assembly in the wheel

pants. e threaded portion of the axle will

t the notch of the wheel pant as shown.

WWW.SEAGULLMODELS.COM

6) Slide the threaded end of the axle through

the hole in the bottom of the landing gear leg.

Use a washer and locknut to tighten the axle

to the landing gear. Make sure to use thread-

lock on the nut so it won’t vibrate loose in

ight as shown.

7) Tighten the setcrews using a hex wrench

to secure the collars on the axle over the at

spot to retain the wheel as shown.

Repeat steps as above to attach remaining

wheel pants to the landing gear.

INSTALLING THE FUSELAGE SERVOS.

Because the size of servos dier, you

mayneedtoadjustthesizeoftheprecutopening

in the mount. e notch in the sides of the

mount allow the servo lead to pass through.

1) Install the rubber grommets and brass

collets onto the throttle servo. Test t the

servo into the aileron servo mount.

2) Secure the servos with the screws provid-

ed with your radio system.

Wheel collar.

Wheel.

Axle.

Washer. M3

Wheel. Wheel collar.

Washer.

nut.--

Lite-Plywood

block.

Wheel Pant.

C/A glue.

M3.

Axle.

rottle Rudder

Elevator

SUPER DAVE MX2 Instruction Manual.

THROTTLE SERVO ARM INSTALLA-

TION.

Install adjustable servo connector in the ser-

vo arm as same as picture below:

Loctite secure.

Adjustable Servo

connector.

Servo arm

1 PCS.

rottle Rudder

Elevator

INSTALLING THE SWITCH.

Install the switch into the precut hole in the

side, in the fuselage.

3/32’’ Hole.

Trim and cut.

Switch.

Trim and cut.

Switch.

MOUNTING THE ENGINE .

1) Position the engine with the drive washer

(125mm) forward of the rewall as shown.

125 mm

Tabla de contenidos

Otros manuales de Juguete de Seagull Models

Seagull Models

Seagull Models BOOMERANG EP Manual de usuario

Seagull Models

Seagull Models EDGE 540 Manual de usuario

Seagull Models

Seagull Models CAP 232 Manual de usuario

Seagull Models

Seagull Models AT-6 TEXAN Manual de usuario

Seagull Models

Seagull Models Mini Nemsis EP Manual de usuario

Seagull Models

Seagull Models Laser 200 Manual de usuario

Seagull Models

Seagull Models DECATHLON ARTF Manual de usuario

Seagull Models

Seagull Models WESTLAND LYSANDER MK. III 55CC SEA216 Manual de usuario

Seagull Models

Seagull Models SEA385 Manual de usuario

Seagull Models

Seagull Models SPARROW HAWK 62 CC Manual de usuario

Seagull Models

Seagull Models YAK 54 Manual de usuario

Seagull Models

Seagull Models SEA 285 Manual de usuario

Seagull Models

Seagull Models ultra-jet Manual de usuario

Seagull Models

Seagull Models CHRISTEN HUSKY SEA180 Manual de usuario

Seagull Models

Seagull Models YAK 52 Manual de usuario

Seagull Models

Seagull Models SEA 94 Pilatus PC-9 Manual de usuario

Seagull Models

Seagull Models Magic Bird EF1 RACER 40E PNP, 46" Manual de usuario

Seagull Models

Seagull Models CURTISS P-40N WARHAWK Manual de usuario

Seagull Models

Seagull Models MINI CHRISTEN EAGLE II N54CE Manual de usuario

Seagull Models

Seagull Models Mini Sparrowhawk EP Manual de usuario

Seagull Models

Seagull Models CAP 232 Manual de usuario

Seagull Models

Seagull Models Spitfire Mk IX Manual de usuario

Seagull Models

Seagull Models EXTRA EA 300L Manual de usuario

Seagull Models

Seagull Models Extra 300S Manual de usuario

Manuales populares de Juguete de otras marcas

marklin

marklin 37321 Manual de usuario

Canon

Canon PAPER CRAFT Manual de usuario

GREAT PLANES

GREAT PLANES Pitts M-12S Manual de usuario

NOCH

NOCH 14261 Manual de usuario

Hausler

Hausler 450 SE V2 Manual de usuario

Dynaflite

Dynaflite Daydream Manual de usuario

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manual

Kenner

Kenner Batman 63651 Manual de usuario

LEGO

LEGO 8527 Manual de usuario

iKarus

iKarus ECO 8 Manual de usuario

Multiplex

Multiplex EasyStar II Manual de instrucciones

Walkera

Walkera 38 Manual de instrucciones

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manual de usuario

MD MXION SWD Manual de usuario

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manual de usuario

marklin

marklin 39671 Manual de usuario

Meccano

Meccano 15103 Manual de usuario

LEGO

LEGO TECHNIC 8735 Manual de usuario