Seagull Models Mini Nemsis EP Manual de usuario

www.seagullmodels.com

ASSEMBLY MANUAL

MS: X114

Specifications:

Wingspan-----------------------38.8in(98.5cm).

Wingarea-------------------248sq.in(16sqdm).

Weight----------------1.9-2.1lbs(0.85-0.95kg).

Length-------------------------------31.1in(79cm).

Speedcontrol(ESC)-------------15A-30Aamp.

Motor -------------------------------------- 450-480.

Radio-----------4channelswith5miniservos.

Battery3-cell1800mAhto2100mAhLi-Po.

10 x 5E Electric Prop.

“Graphics and specifications may change without notice”.

MINI NEMSIS EP Instruction Manual.

INTRODUCTION.

Thank you for choosing the MINI NEMESIS EP ARTF by SEAGULL MODELS COMPANY LTD.

The MINI NEMESIS EP was designed with the intermediate/advanced sport flyer in mind. It is a

semi scale airplane which is easy to fly and quick to assemble. The airframe is conventionally built

usingbalsa,plywoodtomakeitstrongerthantheaverageARTF,yetthedesignallowstheaeroplane

to be kept light. You will find that most of the work has been done for you already.The motor mount

has been fitted and the hinges are pre-installed . Flying the MINI NEMESIS EP is simply a joy.

This instruction manual is designed to help you build a great flying aeroplane. Please read this

manualthoroughlybeforestartingassemblyofyour MININEMESISEP.Usethepartslistingbelow

to identify all parts.

WARNING.

Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is

capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU

ASSUME ALL RISK & RESPONSIBILITY.

IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier

and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training

proceduresdesignedtohelpthenewpilotonhis waytosuccessful R/Cflight.They willalsobe able

to advise on any insurance and safety regulations that may apply.

KIT CONTENTS

488

www.seagullmodels.com

KIT CONTENTS.

1 SEAX11401

2 SEAX11402

3 SEAX11403

4 SEAX11404

5 SEAX11405

6 SEAX11406

7 SEAX11407

8 SEAX11408

9 SEAX11409

ADDITIONAL ITEMS REQUIRED.

Motor 450-480

4 channel radio with 5 mini servos

Suitablepropeller

The control surfaces, including the

ailerons, elevators, and rudder, are

prehinged with hinges installed, but

the hinges are not glued in place. It

is imperative that you properly

adhere the hinges in place per the

steps that follow using a high-quality

thin C/A glue.

HINGING THE AILERONS .

Note:

1) Carefully remove the aileron from one

of the wing panels. Note the position of the

hinges.

2)Remove eachhinge fromthe wingpanel

and aileron and place a T-pin in the center of

each hinge. Slide each hinge into the aileron

untiltheT-pinis snugagainstthe aileron.This

will help ensure an equal amount of hinge is

oneithersideofthehingelinewhentheaileron

is mounted to the wing panel.

Hinge.

T-pin.

TOOLS & SUPPLIES NEEDED.

Thick cyanoacrylate glue

30 minute epoxy

5 minute epoxy

Hand or electric drill

Assorted drill bits

Modellingknife

Straight edge ruler

2mm ball driver

Phillips head screwdriver

220 grit sandpaper

90° square or builder’s triangle

Wire cutters

Masking tape & T-pins

Thread-lock

Paper towels

3) Slide the aileron on the wing panel until

there is only a slight gap. The hinge is now

centered on the wing panel and aileron.

Remove the T-pins and snug the aileron

against the wing panel.A gap of 1/64” or less

shouldbe maintainedbetweenthe wingpanel

andaileron.

MINI NEMSIS EP Instruction Manual.

8)Afterboth ailerons are securelyhinged,

firmly grasp the wing panel and aileron to

make sure the hinges are securely glued and

cannot be pulled out. Do this by carefully

applying medium pressure, trying to separate

the aileron from the wing panel. Use caution

not to crush the wing structure.

7) Repeat this process with the other wing

panel, securely hinging the aileron in place.

6) Using C/A remover/debonder and a

papertowel, removeanyexcessC/Aglue that

may have accumulated on the wing or in the

aileronhingearea.

5)Turn thewing panelover anddeflectthe

aileron in the opposite direction from the

opposite side. Apply thin C/A glue to each

hinge,makingsure thattheC/Apenetratesinto

both the aileron and wing panel.

Workthe aileron upanddownseveral

times to “work in” the hinges and

check for proper movement.

Note:

4) Deflect the aileron and completely

saturate each hinge with thin C/A glue. The

aileronsfront surfaceshould lightlycontactthe

wing during this procedure. Ideally, when

thehinges are glued in place, a 1/64” gap or

less will be maintained throughout the lengh

of the aileron to the wing panel hinge line.

Hinge.

Thehinge isconstructedof aspecial

material that allows the C/A to wick

or penetrate and distribute

throughout the hinge, securely

bonding it to the wood structure of

the wing panel and aileron.

Note:

HINGING THE ELEVATORS.

Glue the elevator hinges in place using the

same techniques used to hinge the ailerons.

www.seagullmodels.com

HINGING THE RUDDER.

Glue the rudder hinges in place using the

same techniques used to hinge the ailerons.

INSTALL THE AILERONS CONTROL

HORN.

Hinge.

Epoxy.

Aileronfiberglass

control horn .

INSTALL ELEVATOR CONTROL HORN.

INSTALL RUDDER CONTROL HORN.

Elevatorfiberglass

controlhorn.

Epoxy.

Fiberglass

control horn.

Fiberglass

control horn.

Fiberglass

control horn.

MINI NEMSIS EP Instruction Manual.

INSTALLING THE FUSELAGE SERVOS.

Elevator servo.

Rudder servo.

1) Installtherubber grommetsand brass

colletsontothe throttleservo. Testfitthe servo

into the aileron servo mount.

 2) Secure the servos with the screws pro-

vided with your radio system.

Because the size of servos differ, you

mayneed toadjustthe sizeoftheprecutopen-

ing in the mount. The notch in the sides of the

mount allow the servo lead to pass through.

Rudder fiberglass

control horn.

Epoxy.

Cut.

Elevator servo.

Rudder servo.

Cut.

FUSELAGE SERVO ARM INSTALLATION.

Installadjustableservo connectorinthe servo

arm as same as picture below:

WHEEL AND WHEEL PANTS.

1) Assembling and mounting the wheel

pants to the landing gear as shown below

pictures.

Elevator servo arm.

www.seagullmodels.com

2) Follow diagram below for wheel pant

installation:

3) You have to trim each axle using a toll

cutting and cut-off wheel.

Cautionwhencutting theaxlesand wear

protective goggles.

INSTALLING THE MAIN LANDING GEAR

TO FUSELAGE.

 5) The blind nuts for securing the landing

gearare alreadymountedinsidethefuselage.

 6) Using the hardware provided, mount

the main landing gear to the fuselage.

 7) Placethe fuselageinverted onthework-

benchin asuitable stand.Set thelanding gear

in place and use a screwdrive to secure the

landing gear to the fuselage using bolts

M4x20mmand washers.Make sureto usethe

threadlock on the bolts so they don’t vibrate

loose.



4) A drop of C/A glue on the wheel collar

screws will help keep them from coming lose

duringoperation.

Repeat the process for the other wheel.

wheel Pant.

wheel.

M3.

wheel collar.

nut. Axle.

Washer.

Lite-Plywood

block.

MINI NEMSIS EP Instruction Manual.

2) Place the servo between the mounting

blocksandspace itfromthehatch. Useapencil

to mark the mounting hole locations on the

blocks.

3) Use drill bit in a pin vise to drill the mouting

holes in the blocks.

1) Usinga small weight(Weightedfuelpick-up

workswell) andstring, feed thestring through

the wing as indicated.

Because the size of servos differ, you

mayneedto adjustthesize oftheprecutopen-

ing in the mount. The notch in the sides of

themountallowtheservoleadtopassthrough.

4) Apply 2-3 drops of thin C/A to each of the

mounting holes. Allow the C/Ato cure without

using accelerator.

6) Secure the servo to the aileron hatch using

Phillips screwdriver and the screws provided

with the servo.

5) Use dental floss to secure the connection

so they cannot become unplugged.

Lockerglue.

M3 x 10mm.

Servos.

Smallweight. Thread.

INSTALLING THEAILERON.

www.seagullmodels.com

7) Apply 1-2 drops of thin C/A to each of the

mounting tabs. Allow the C/A to cure without

using accelerator.

8) A string has been provided in the wing to

pull the aileron lead through to the wing root.

Remove the string from the wing at the servo

location and use the tape to attach it to the

servoextension lead.Pull theleadthroughthe

wing and remove the string.

9) Set the aileron hatch in place and use a

Phillips screw driver to install it with four wood

screws.

Aileronservo.

MINI NEMSIS EP Instruction Manual.

M3 x 15mm.

Electric motor.

140mm.

4mm.

2) Attach the electric motor box to the firewall

suitable with the cross lines drawn on the electric

motor box and firewall. Using epoxy and balsa

stick to secure the motor box to the firewall.

Please see pictures below.

3) Attach the motor to the front of the electric

motor box using four 3mm blind nut, four

M3x15mm hex head bolts to secure the motor.

Please see picture shown.

Epoxy.

Balsa.

Epoxy.

ELECTRIC POWER ASSEMBLY.

1) Locate the items neccessary to install the

electric power installation.

15A-30A.

450-480.

Tabla de contenidos

Otros manuales de Juguete de Seagull Models

Seagull Models

Seagull Models A6M Zero Fighter 67 Manual de usuario

Seagull Models

Seagull Models T-34C MENTOR Manual de usuario

Seagull Models

Seagull Models GLASAIR Sportsman GS-2 Manual de usuario

Seagull Models

Seagull Models T-6A Texan II Manual de usuario

Seagull Models

Seagull Models Van's RV-8 Manual de usuario

Seagull Models

Seagull Models SAVAGE CRUISER MS:195 Manual de usuario

Seagull Models

Seagull Models NIEUPORT 28 REPLICA Manual de usuario

Seagull Models

Seagull Models P47 SNAFU Manual de usuario

Seagull Models

Seagull Models PERCIVAL MEW GULL Manual de usuario

Seagull Models

Seagull Models Embraer EMB-312 Tucano T-27 Brazilian Air Force 85 span... Manual de usuario

Seagull Models

Seagull Models YAK 55 Manual de usuario

Seagull Models

Seagull Models DECATHLON ARTF Manual de usuario

Seagull Models

Seagull Models L-4 Grasshopper 90 inches Manual de usuario

Seagull Models

Seagull Models YAK 11 Manual de usuario

Seagull Models

Seagull Models De Havilland DH-60M Moth 72" wingspan... Manual de usuario

Seagull Models

Seagull Models CAP 232 Manual de usuario

Seagull Models

Seagull Models YAK 52 Manual de usuario

Seagull Models

Seagull Models AT-6 TEXAN Manual de usuario

Seagull Models

Seagull Models BOOMERANG EP Manual de usuario

Seagull Models

Seagull Models Mini Sparrowhawk EP Manual de usuario

Seagull Models

Seagull Models SEA385 Manual de usuario

Seagull Models

Seagull Models YAKOVLEV YAK 3 Manual de usuario

Seagull Models

Seagull Models SEA231 Manual de usuario

Seagull Models

Seagull Models JUMPER 25 Manual de usuario

Manuales populares de Juguete de otras marcas

marklin

marklin 37321 Manual de usuario

Canon

Canon PAPER CRAFT Manual de usuario

GREAT PLANES

GREAT PLANES Pitts M-12S Manual de usuario

NOCH

NOCH 14261 Manual de usuario

Hausler

Hausler 450 SE V2 Manual de usuario

Dynaflite

Dynaflite Daydream Manual de usuario

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manual

Kenner

Kenner Batman 63651 Manual de usuario

LEGO

LEGO 8527 Manual de usuario

iKarus

iKarus ECO 8 Manual de usuario

Multiplex

Multiplex EasyStar II Manual de instrucciones

Walkera

Walkera 38 Manual de instrucciones

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manual de usuario

MD MXION SWD Manual de usuario

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manual de usuario

marklin

marklin 39671 Manual de usuario

Meccano

Meccano 15103 Manual de usuario

LEGO

LEGO TECHNIC 8735 Manual de usuario