Seagull Models SEA 285 Manual de usuario
1
Specications:
Wingspan--------------- 80.0 in (203.2 cm).
Wing area--------------- 957.9 sq.ins (61.8 sq.dm).
Weight------------------- 13.7-14.1 lbs (6.2-6.4 kg).
Length------------------- 58.8 in (147.2 cm).
Engine/Motor size----- 0.46-0.55 cu.in 2stroke.
Radio--------------------- 8 channels with 10 servos.
ASSEMBLY MANUAL
Code : SEA 285
Seagull de Havilland Mosquito Twin Engine RC Warbird Instruction Manual.
2
1
5 5
2
4710
68
9
ank you for choosing the Seagull de Havilland Mosquito Twin Engine RC War-
bird ARTF by SG MODELS . e Seagull de Havilland Mosquito Twin Engine RC
Warbird was designed with the intermediate/advanced sport yer in mind. It is a semi
scale airplane which is easy to y and quick to assemble. e airframe is convention-
ally built using balsa, plywood to make it stronger than the average ARTF, yet the de-
sign allows the aeroplane to be kept light. You will nd that most of the work has been
done for you already. e motor mount has been tted and the hinges are pre-installed.
Flying the Seagull de Havilland Mosquito Twin Engine RC Warbird is simply a joy.
is instruction manual is designed to help you build a great ying aeroplane. Please read
this manual throughly before starting assembly of your Seagull de Havilland Mosquito
Twin Engine RC Warbird Use the parts listing below to indentify all parts.
Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is ca-
pable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & REPONSIBILITY.
If you are inexperienced with basic R/C ight we strongly recommend you contact your R/C
supplier and join your local R/C model Flying Club. R/C Model Flying Clubs oer a variety
of training procedures designed to help the new pilot on his way to successful R/C ight.
ey will also be able to advise on any insurance and safety regulations that may apply.
INTRODUCTION.
WARNING.
KIT CONTENTS
3
3
2
3
KIT CONTENTS.
SEA285 Seagull de Havilland
Mosquito Twin Engine RC Warbird
1. Fuselage
2. Wing set (2)
3. Tail set (2)
4. Canopy
5. Cowling (2)
6. landing gear
7. Pilot
8. wheel (2)
9. Aluminum wing tube
10. EP Conversion pack
ADDITIONAL ITEMS REQUIRED.
TOOLS & SUPPLIES NEEDED.
in cyanoacrylate glue.
Medium cyanoacrylate glue.
30 minute epoxy.
5 minute epoxy.
Hand or electric drill.
Assorted drill bits.
Modelling knife.
Straight edge ruler.
2mm ball driver.
Phillips head screwdriver.
220 grit sandpaper.
90° square or builder’s triangle.
Wire cutters.
Masking tape & T-pins.
read-lock.
Paper towels.
�0.46-0.55 cu.in 2stroke.
�Computer radio 8 with chanlel 10
servos.
�Glow plug to suit engine.
�Propeller to suit engine.
�Protective foam rubber for radio
system.
INSTALL THE AILERONS
CONTROL HORN.
Epoxy.
Fiberglass control horn
Epoxy.
Epoxy.
Fiberglass control horn
Seagull de Havilland Mosquito Twin Engine RC Warbird Instruction Manual.
4
INSTALLING THE ALLERON SERVOS.
Epoxy.
Fiberglass control horn
5
Because the size of servos dier,
you may need to adjust the size of the
precut opening in the mount. e notch
in the sides of the mount allow the servo
lead to pass through.
1) Place the servo between the mount-
ing blocks and space it from the hatch.
Use a pencil to mark the mounting hole
locations on the blocks.
2) Use drill bit in a pin vise to drill the
mouting holes in the blocks.
4) Use dental oss to secure the connec-
tion so they cannot become unplugged.
5) Secure the servo to the aileron hatch
using Phillips screwdriver and the screws
provided with the servo.
3) Apply 2-3 drops of thin C/A to each
of the mounting holes. Allow the C/A to
cure without using accelerator.
C/A glue
6) Apply 1-2 drops of thin C/A to each of
the mounting tabs. Allow the C/A to cure
without using accelerator.
C/A glue
Seagull de Havilland Mosquito Twin Engine RC Warbird Instruction Manual.
6
7) Remove the string from the wing at the
servo location and use the tape to attach it
to the servo extension lead. Pull the lead
through the wing and remove the string.
8) Set the aileron hatch in place and use
a Phillips screw driver to install it with
four wood screws.
2x10mm
AILERON PUSHROD INSTALLATION.
Please see below pictures.
Fuel Tubin g
Hex Nut
Metal R/C Clevis
Pushrod Wire
7
INSTALLING THE FLAP SERVO.
Repeat the procedure for the ap servo.
INSTALLING THE FLAP PUSHROD.
Repeat the procedure for the aileron
pushrod.
Fuel Tubin g
Hex Nut
Metal R/C Clevis
Pushrod Wire
.
INSTALLING THE FUSELAGE SERVOS.
.
Because the size of servos dier, you
may need to adjust the size of the precut
opening in the mount. e notch in the
sides of the mount allow the servo lead to
pass through.
1) Install the rubber grommets and brass
collets into all servos. Test t the servos
into the fuselage servo mounts.
2) Secure the servos with the screws pro-
vided with your radio system.
Elevator servo.
Rudder servo.
Seagull de Havilland Mosquito Twin Engine RC Warbird Instruction Manual.
8
Trim and cut.
INSTALLING THE RECEIVER SWITCH.
Install the switch into the precut hole in
the side, in the fuselage.
3/32” Hole.
.
Switch.
ENGINE MOUNT INSTALLATION
1) Locate the items necessary to install the en-
gine mount included with your model
2) Use four 4x20mm head bolts and
four 4mm washers to attach the engine
mount rails to the rewall. Tighten the
screws . Make sure to use threadlock on
the screws to help prevent them from vi-
brating loose
Elevator servo arm.
Rudder servo arm.
9
Knife.
1) Position the engine with the drive
washe (118mm) forward of the rewall
as shown.
2) Use a pin drill and 2mm drill bit to
drill a small indentation in the mount
for the engine mounting screw.
3) Use a drill to drill the four holes in the
engine mount rails
4mm.
2mm.
118mm.
Epoxy.
Seagull de Havilland Mosquito Twin Engine RC Warbird Instruction Manual.
10
INSTALLING THE STOPPER
ASSEMBLY.
1) Using a modeling knife, carefully cut
o the rear portion of one of the 3 nylon
tubes leaving 1/2” protruding from the
rear of the stopper. is will be the fuel
pick up tube.
2) Using a modeling knife, cut one length
of silicon fuel line. Connect one end of the
line to the weighted fuel pick up and the
other end to the nylon pick up tube.
3) Carefully bend the second nylon tube up
at a 45º angle. is tube is the vent tube.
Vent tube. Fuel pick up tube.
Fuel fill tube.
4) Test t the stopper assembly into the
tank. It may be necessary to remove some
of the ashing around the tank opening us-
ing a modeling knife. If ashing is present,
make sure none falls into the tank.
Tabla de contenidos
Otros manuales de Juguete de Seagull Models
Seagull Models
Seagull Models T-6A Texan II Manual de usuario
Seagull Models
Seagull Models HARMON ROCKET III Manual de usuario
Seagull Models
Seagull Models Pilatus PC-6 Porter Manual de usuario
Seagull Models
Seagull Models Extra 260 Manual de usuario
Seagull Models
Seagull Models Mehari Aerobatics CEA-309 Manual de usuario
Seagull Models
Seagull Models SEA 334 Manual de usuario
Seagull Models
Seagull Models YAK 11 Manual de usuario
Seagull Models
Seagull Models JU-87 STUKA GIANT SCALE Manual de usuario
Seagull Models
Seagull Models YAKOVLEV YAK 3 ARF Manual de usuario
Seagull Models
Seagull Models DECATHLON ARTF Manual de usuario
Seagull Models
Seagull Models A6M Zero Fighter 67 Manual de usuario
Seagull Models
Seagull Models Zivko Edge 540 V3 Manual de usuario
Seagull Models
Seagull Models HARRIER 3D Manual de usuario
Seagull Models
Seagull Models JUMPER 25 Manual de usuario
Seagull Models
Seagull Models KA8-B Manual de usuario
Seagull Models
Seagull Models Embraer EMB-312 Tucano T-27 Brazilian Air Force 85 span... Manual de usuario
Seagull Models
Seagull Models P-47D Thunderbolt 60 Manual de usuario
Seagull Models
Seagull Models MESSERSCHMITT BF109E 60 Manual de usuario
Seagull Models
Seagull Models ISPORTS 10cc Manual de usuario
Seagull Models
Seagull Models SEA FURY Manual de usuario
