Schier FCR10 Manual de usuario

Contents

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Special Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Getting to Know the FCR10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

SPECIFICATION AND INSTALLATION GUIDE

FCR10 Field Cut Riser System

For Use with Sampling Port Model SV10

Notes

RISER SIDE VIEW

ø 7-7/8" ID

ø 9-1/8" OD

33"

Riser Height Needed Risers Required

0" - 31" FCR10

>31" - 64" FCR10 (x2)

>64" - 97" FCR10 (x3)

1. Unit weight: 6 lbs.

2. Riser not designed to hold water

Engineer Specification Guide:

Field-cut adjustable riser system to consist of 8"

nominal diameter polyethylene corrugated

drainage pipe and coupling, and butyl mastic

tape for riser joints. Riser shall allow field

adjustability of cover to grade.

Installation Note

Riser system may be stacked no more than three

units high to a maximum of 97" extension.

MODEL NUMBER:

FCR10

DESCRIPTION: SV10 Sampling Port Field Cut Riser System

PART #: 8010-020-01 DWG BY: B. Karrer DATE: 3/1/2020 REV: ECO:

GETTING TO KNOW THE FCR10

Read all instructions before installation Install in conformance with all local codes

SPECIAL PRECAUTIONS

Do not install this unit in any manner

except as described in these instructions.

Doing so may result in property damage, personal injury or death.

DO NOT AIR TEST UNIT OR RISER SYSTEM!

For Schier Grease Interceptor Installations - Failure to follow this guidance

voids your warranty

3 Risers (97") Max

Provide at least 16"

clearance above unit for

routine maintenance.

16" min.

Max Water Level

Risers are

not designed

to retain water

2Install sampling port as

close as possible to and

downstream from

interceptor being served

1. Corrugated Riser Pipe (8" nominal diamater - 33" height)

2. Riser-Riser Coupling

3. 2" x 33" Butyl Mastic Tape (x2)

4. 2" x 6" Butyl Mastic Tape

page 2 of 4

FCR10 Installation Guide

INSTALLATION

Tools You

Will Need

1 Prepare SV10 Sampling Port for Riser Installation

Measure dimension X to determine riser height needed.

Disconnect the SV10 and remove it from the burial

pit. Cut the SV10 at the Riser Cut Line, freeing the

cover adapter from the sampling port body.

Riser Height Risers

Needed Required

>0" - 31" FCR10

>31" - 64" FCR10 (x2)

>64" - 97" FCR10 (x3)

Reciprocating Saw,

Circular Saw or Jigsaw

Tape

Measure Level Square

page 3 of 4

FCR10 Installation Guide

Go to Step 3 - Cut and Install Riser>0 - 31"

RISER HEIGHT NEEDED

Follow Steps 2a -2c to join two FCR10 risers>31 - 64"

Follow Steps 2a -2c to join three FCR10 risers>64 - 97"

Spread open the corrugated pipe

coupling slightly and slip in the

ends of the riser pipes to be joined.

Use the 2 - 33" long rolls of butyl

tape provided to seal and secure

the horizontal riser seams.

Use the 6" long roll of butyl tape

provided to seal and secure the

vertical coupling seam.

2Assemble Multiple Risers for Deep Burials

INSTALLATION

3 Cut and Install Riser

Insert Riser into SV10 Body.

Return the SV10 to the burial pit and

reconnect the drain lines

3d 3e

Place the cover/cover adapter

onto the top of the riser and

check to see if flush with grade.

If too high, remove cover and

trim riser as needed.

Secure cover/cover adapter using

the other 33" length of butyl tape

(provided with SV10). Make sure joint

is completely sealed and cover is

level and flush-to-grade.

Use a 33" length of butyl tape (provided

with SV10) to secure the riser joint. Make

sure joint is completely sealed and riser

is aligned square to the SV10 Body.

3c3a

Cut riser to a length 2" longer than

the riser height needed.

x+2"

page 3 of 4

FCR10 Installation Guide

Otros manuales de Producto de plomería de Schier

Schier

Schier SI-50 Manual de usuario

Schier

Schier PP3 Manual de usuario

Schier

Schier SV10 Manual de usuario

Schier

Schier GB-250 Manual de usuario

Schier

Schier GB-1000-L Manual de usuario

Schier

Schier GB2-CT Manual de usuario

Schier

Schier GB-50 Manual de usuario

Schier

Schier GB-250 Manual de usuario

Schier

Schier GB2 Manual de usuario

Schier

Schier GB2 Manual de usuario

Schier

Schier GB1-CT Manual de usuario

Schier

Schier GB-500-500HF Manual de usuario

Schier

Schier GB-250-B Manual de usuario

Schier

Schier GB-500-B Manual de usuario

Schier

Schier GB-500 Manual de usuario

Schier

Schier GB3-CT Manual de usuario

Schier

Schier SI-75 Manual de usuario

Schier

Schier GB3 Manual de usuario

Schier

Schier GB-50 Manual de usuario

Schier

Schier SI-250 Manual de usuario

Schier

Schier GB-75 Manual de usuario

Schier

Schier GB-500-500HF Manual de usuario

Schier

Schier PP3 Manual de usuario

Schier

Schier FCR2 Manual de usuario

Manuales populares de Producto de plomería de otras marcas

Weka

Weka 506.2020.00E Instrucciones de funcionamiento

Kohler

Kohler K-6228 Instrucciones de montaje

UBERHAUS DESIGN

UBERHAUS DESIGN 75175017 Manual de usuario

American Standard

American Standard DetectLink 6072121 Manual de usuario

Uponor

Uponor Contec TS Manual de usuario

Pfister

Pfister Selia 49-SL Manual de usuario

Fortis

Fortis VITRINA 6068700 Manual de usuario

Fortis

Fortis MILANO 78211JS Manual de usuario

Kohler

Kohler K-12183 Instrucciones de montaje

Maxxus

Maxxus MX-M206-01 Manual de usuario

Moen

Moen 5922 Series Manual de usuario

Viega

Viega Prevista Pure 8512 Manual de usuario

Kohler

Kohler Centerset K-15240 Instrucciones de montaje

Viega

Viega Prevista Dry 8522.33 Manual de usuario

Sanela

Sanela Lema SLP 59RB Manual de usuario

Elkay

Elkay EDF15AC Manual de instalación

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Manual

baliv

baliv WT-140 Manual de usuario