SAT-Kabel TVmeter HD-T Guía de configuración

Correct power OFF/ON procedure for meters to avoid occasional

Memory Plans and navigation cancellation

The red button has four timed functions:

1st) One shot = turn-ON

2nd) One shot (when on) = always goes the to HOME MENU

3rd) If kept pressed for 2 seconds = turn-OFF

4th) Kept pressed for about 10 seconds = HW reset, Forced turn-off, (interrupts the

ongoing data saving in memory).

POWER ON:

Press once the red button and wait until the start -up is completed, about 20

seconds (do not press it again during the start-up phase).

POWER OFF:

Press and hold the red button , the instrument will emit a first beep immediately

and a second BEEP after about 2 seconds, then release immediately the red button

(even if the display is still active and shows the batteries instructions).

CAUTION:

Do not keep pressed the red button after the second BEEP, to avoid starting the

HW reset function (forced turn-off see poit 4). Basically, every time you turn off the

instrument, it needs about ten seconds to save the data in memory before turn-off. If

accidentaly you interrupt this storing process, activating the HW Reset function the

data in memory could be corrupted. In any case you can restore the memory plans

yourself with a PC.

TVmeter HD-T / TVmeter HD

Self Repair

Your Meter has lost memory plans, TV Channel Plan

and Transponder SAT?

The total or partial cancellation, of the plans of memory and SAT & TV, can occur

randomly and rarely for a wrong turning off the power. Basically if you normally take

and hold the RED button "Home" for more than two seconds (eg 6 or 7 seconds) in

some rare cases, it may conflict with the "reset"; while the tool (which is shutting

down) is still saving the data in memory.

Correct procedure for instruments:

·Press and hold the red button , the instrument will emit a first beep

immediately and a second BEEP after about 2 seconds, then release

immediately the red button (even if the display is still active and shows the

batteries instructions).

CAUTION:

·Do not keep pressed the red button after the second BEEP, to avoid starting the

HW reset function (forced turn-off see poit 4). Basically, every time you turn off the

instrument, it needs about ten seconds to save the data in memory before turn-off. If

accidentaly you interrupt this storing process, activating the HW Reset function the

data in memory coul be corrupted. In any case you can restore the memory plans

yourself with a PC.

IMPORTANT: In SINGLE DISPLAY COLOR models before to reload/update the

memory Plans and the SW, it is necessary to do a FORMAT HD (Figure 1) to fully

clean the memories of your instrument.

Figure 1: Menu selection "FORMAT HARD DISK"

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de SAT-Kabel

SAT-Kabel

SAT-Kabel IRM?20 Manual de usuario

SAT-Kabel

SAT-Kabel IRM 5 MMC Manual de usuario

SAT-Kabel

SAT-Kabel IRM 7 Manual de usuario

SAT-Kabel

SAT-Kabel SPM 22 PF Manual de usuario

SAT-Kabel

SAT-Kabel SPM 6PC Manual de usuario

SAT-Kabel

SAT-Kabel AMS-FS433 Manual de usuario

SAT-Kabel

SAT-Kabel IRM 5 Manual de usuario

SAT-Kabel

SAT-Kabel IRM?70 SD Manual de usuario

SAT-Kabel

SAT-Kabel CATVmeter Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario