Sanyo VCb-3100P Manual de usuario
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUEL D’INSTRUCTIONS
B/W CCD Camera
CCD-Schwarzweißkamera
Caméra CCD Noir et Blanc
CCD
VCB-3100P
VCB-3170P
About this manual
•Before installing and using the camera, please
read this manual carefully. Be sure to keep it
handy for later reference.
•This manual gives basic connections and
operating instructions for 2 PAL models
( CB-3170P, 3100P).
Über diese Bedienungsanleitung
•Lesen Sie bitte vor der Montage und dem
Inbetriebnehmen der Kamera zuerst diese
Bedienungsanleitung sorgfältig durch und
bewahren Sie sie zum späteren Nachschlagen
auf.
•In dieser Anleitung finden Sie die Anschlüsse
und die Grundbedienung für 2 PAL-Modelle
( CB-3170P und 3100P)
•
!
•
"#
2
$
PAL
%
(VCB-3170P,
3100P)
&'()*+,-!
À propos de ce manuel
•Avant d’installer et d’utiliser la caméra, veuillez
lire ce manuel attentivement. Gardez-le à
portée de main pour toute référence ultérieure.
•Ce manuel couvre les branchements et
instructions pour l’utilisation de base pour 2
modèles de format PAL ( CB-3170P et 3100P).
L73M5, N5/XE GB 1996, 10, 31
Depending on the conditions of use,
installation and environment, please be
sure to make the appropriate settings and
adjustments. If you need help with
installation and/or settings, please consult
your dealer.
CONTENTS
PRECAUTIONS...................................................2
PARTS NAMES...................................................3
MOUNTING THE LENS ......................................5
CONNECTIONS..................................................7
SETTINGS...........................................................8
TROUBLESHOOTING.......................................12
SPECIFICATIONS .............................................13
ACCESSORIES
1C mount adaptor ( mm)................1 pc.
The C mount adaptor must be used to
be able to install a C mount lens on the
camera.
2Lens iris plug (4-pin) ........................1 pc.
12
FEATURES
•Built-in interline transfer method 1/3"
CCD
– Model VCB-3100P approx. 320,000
picture elements
– Model VCB-3170P approx. 470,000
picture elements
•Low smear, anti-blooming, low lag, no
burning and no geometric distortion
using the CCD solid state image device.
•100% solid state components giving
excellent immunity to shock and
vibration
•Not subject to interference from
magnetic or electrostatic fields
•High sensitivity, minimum required
illumination of 0,1 lux with F1.2 lens
•Horizontal resolution
– Model VCB-3100P more than 400 TV
lines
– Model VCB-3170P more than 60 TV
lines
•Built-in high speed electronic shutter
(with selectable speed setting by
internal switches)
•New backlight compensation function
(Model VCB-3170P: active when using
an auto-iris lens)
•Externally adjustable flange back
(mechanical focus)
•Low power consumption and quick start
L73M , N /XE GB 1996, 10, 31
English 1
PRECAUTIONS
In case of problem
Do not use the camera if smoke or a
strange odour comes from the unit, or if it
seems not to function correctly. Disconnect
the power cord immediately, and consult
your dealer (or a Sanyo Authorized Service
Centre).
Do not open or modify
Do not open the cabinet, as it may be
dangerous and cause damage to the unit.
For internal settings and repairs, consult
your dealer (or a Sanyo Authorized Service
Centre).
Do not put ob ects inside the unit
Make sure that no metal objects or
flammable substance get inside the camera.
If used with a foreign object inside, it could
cause a fire, short-circuits or damages.
If water or a liquid gets inside the camera,
disconnect the power cord immediately,
and consult your dealer (or a Sanyo
Authorized Service Centre). Be careful to
protect the camera from rain, sea water,
etc.
Be careful when handling the unit
To prevent damages, do not drop the
camera or subject it to strong shock or
vibration.
Install away from electric or
magnetic fields
If installed close to a TV, radio transmitter,
magnet, electric motor, transformer, audio
speakers the magnetic field they generate
will distort the image.
Protect from humidity and dust
To prevent damages to the camera, do not
install it where there is greasy smoke or
steam, where the dampness may get too
high, or where there is a lot of dust.
Protect from high temperatures
Do not install close to stoves, or other heat
generating devices, such as spotlights, etc.,
or where it could be subject to direct
sunlight, as that could cause deformation,
discoloration or other damages.
Be careful when installing close to the
ceiling, in a kitchen or boiler room, as the
temperature may raise to high levels.
Install where the temperature range will
stay between –10˚C and 0˚C.
(no condensation)
Cleaning
•Dirt can be removed from the cabinet
by wiping it with a soft cloth. To
remove stains, wipe with a soft cloth
moistened with a soft detergent
solution and wrung dry, then wipe dry
with dry soft cloth.
•Do not use benzine, thinner or other
chemical product on the cabinet, as that
may cause deformation and paint
peeling. Before using a chemical cloth,
make sure to read all accompanying
instructions. Make sure that no plastic
or rubber material comes in contact
with the cabinet for a long period of
time, as that may cause damage or
paint peeling.
ENGLISH
L73M , N /XE GB 1996, 10, 31
2 English
PARTS NAMES
1Power indicator (POWER)
Comes on when the power to the camera is on.
2Video output connector (VIDEO OUT: BNC type)
Connect this connector to a device such as a VCR or monitor
with a VIDEO IN connector.
3AC power cord
4External sync composite video signal input connector
(VS IN: BNC type)
Connect to this connector the synchronizing signal output
from a synchronizing signal device or the composite signal of
a video distributor.
5Line phase ad ustment screw (LINE PHASE)
When using two cameras or more, the image on the
monitor may roll vertically when switching sources. This
rolling can be minimized by turning this screw.
6Lens mount cap
The cap is installed to protect the lens mount section.
Remove the lens mount cap before installing a lens (sold
separately).
7Camera installation bracket
The bracket can be fixed at the top or bottom of the
camera. When fixing the bracket, be sure to use the longer
screws and install the shorter screws on the opposite side to
seal the openings.
CAUTION:
When installing the camera support, select a location
that can support the total weight of the camera and
accessories.
1232
1
6
7
1
3
2
5
4
1Shorter screws: M3x4
2Longer screws: M3x6
3Camera mounting
screw hole: 1/4"-20
UNC
L73M , N /XE GB 1996, 10, 31
English 3
8Lens iris output connector (4 pin)
This 4-pin connector is used to send the DC control signal
and power supply to an auto-iris type lens.
9Camera setup section (under the cover)
This unit factory settings are as indicated below. These
settings are for when using a 1/3 inch CS mount DC
(without EE internal amplifier) type lens. However, if due to
installation conditions or environment the settings may need
to be modified for best results (see page 8 "SETTINGS"). To
access the controls, remove the cover fixing screw, then
remove the cover.
Control name VCB-3170P VCB-3100P
aInternal/Line lock switch
(SYNC) INT
bAuto gain control switch (AGC) ON
cHigh speed electronic shutter
switches (E.S.) All OFF: 1/50 sec
dElectronic iris (EI)/
Backlight compensation (BLC)
switch
OFF –
eBacklight compensation
switch (BLC) –OFF
fElectronic iris switch (EI) –
gAuto-iris lens switch
(A.I. LENS) DC
hLens iris level volume (LEVEL) about centre
Note:
•The EI/BLC switch d is used for an auto-iris lens,
therefore the two settings cannot be used simultaneously.
•When using a 1/2 or 2/3 inch C mount VIDEO (with EE
internal amplifier) auto-iris type lens, set the A.I. LENS
switch to the VIDEO position.
9
4
1
2
3
8
ON
OFF
ON
E. S.
BLC
L
E
V
E
L
DC
VIDEO
A. I.
LENS
LH
VR301
ON
123
EI
OFF
ON
SYNC
L-L
INT
VR302
AGC
h
[VCB-3170P]
ab c d g
E. S.
L
E
V
E
L
DC
VIDEO
A. I.
LENS
LH
VR301
ON
123
OFF
ON
L-L
INT
AGCSYNC
ON
OFF
BLC EI
h
ab c f ge
[VCB-3100P]
L73M , N /XE GB 1996, 10, 31
4 English
PARTS NAMES
FFlange-back ad ustment screw (FLANGE BACK ADJ.)
GFlange-back lock screw (FLANGE BACK LOCK)
Flange-back ad ustment
If the pick-up surface is not correctly positioned with relation
to the lens focal point, the picture will be out of focus (in
particular when using auto-iris power zoom lenses, sold
separately). If that is the case, adjust the flange-back position
as described below.
1Using a + screwdriver, loosen the FLANGE BACK LOCK
screw (M2:+).
Set the zoom lens to the maximum telephoto position,
set the focus using the focus ring on the lens.
2Set the zoom lens to the maximum wide angle position,
set the focus using the FLANGE BACK ADJ. screw.
3Repeat steps 2 and 3, until the image stays in focus when
changing from a telephoto shot to a wide angle shot.
When the setting is complete, tighten the FLANGE
BACK LOCK screw.
MOUNTING THE LENS
Check the lens mount
Do not use a lens if the length “L” is more than 7 mm.
That may damage the camera and prevent proper
installation.
Installation of a DC type auto-iris lens (sold
separately)
A 1/3 inch CS mount type lens without EE amplifier circuit
that only uses a DC power source. This camera can receive
(the A.I. LENS switch to the DC type) a CS mount type lens
without the need of an adaptor.
If the lens plug shape or wiring does not correspond, please
install the supplied plug as indicated in the pin layout table.
L
1G
F
1
3
LOCK
2
ADJ.
L73M , N /XE GB 1996, 10, 31
English 5
DC
VIDEO
4
Installation of a VIDEO type auto-iris lens
(sold separately)
A 1/2 or 2/3 inch C mount type lens with EE amplifier circuit
that uses the video signal and a DC power source.
1Remove the lens mount cap.
2Attach the supplied C mount adaptor (A) to the
auto-iris lens (B), then install the assembly on the camera.
3Connect the lens plug to the LENS connector on the side
of the camera.
If the lens plug shape or wiring does not correspond to
the specifications below, connect the supplied plug as
indicated.
•When using lenses from other makers, make sure that
the pins connections in the plug correspond to the
ones of the camera.
Refer to the lens specifications to check the pins
connections in the plug.
•If they are different than indicated, remove the original
plug and connect the supplied plug according to the
diagram.
4Set the A.I. LENS switch in the camera setup section to
the VIDEO position.
Pin layout
DC type lenses VIDEO type lenses
1Brake coil (–) +12 V DC ( 0 mA max.)
2Brake coil (+) Not used
3Drive coil (+) Video output (1.0 Vp-p, high
impedance)
4Drive coil (–) Ground (for video signal and DC
power)
2 (A) (B)
3 (C)
31
2
4
L73M , N /XE GB 1996, 10, 31
6 English
MOUNTING THE LENS
If using Sanyo (DC type) auto-iris lens
•VCL-CS8LY: Standard angle, f= 8 mm
•VCL-CS4LY: Wide angle, f= 4 mm
•VCL-CS2LY: Ultra-wide angle, f= 2.8 mm
If using a VIDEO type auto-iris lens
•Set the ALC and LEVEL controls on the lens to adjust the
iris. Normally the ALC volume should be turned all the
way to Av (Average).
•Depending on the type of lens used, the lens may not
perform properly. In such a case, adjust the LEVEL
volume on the lens casing to correct.
Compatible auto-iris lenses
•f= 9 mm (Standard angle), f= 12 mm (Telephoto), f= 16
mm (More telephoto)
(A)
1
2
(Video signal connections)
: VIDEO IN
: VIDEO OUT
CONNECTIONS
Basic co ectio for mo itori g or recordi g
The peripheral devices (VCR, monitor, lens, etc.) and
cables are sold separately.
1Make the video signal connection between the camera
and the monitor or time lapse VCR.
2Insert the plug of this power cord into a wall outlet.
The POWER indicator (A) will light. Adjust the picture on
the monitor using the Brightness and Contrast controls.
Coaxial cable type and maximum length
•Cable type RG- 9U (3C-2V), 2 0 m maximum.
•Cable type RG-6U ( C-2V), 00 m maximum.
•Cable type RG-11U (7C-2V), 600 m maximum.
CAUTION:
•The RG- 9U type cable should not be run through
electrical conduits or through the air.
•Using CCTV/Video-grade coaxial cable.
L73M , N /XE GB 1996, 10, 31
English 7
SETTINGS
Line phase ad ustment
When using a camera switcher to connect 2 cameras or more to
one monitor, there may be a vertical roll of the images when
switched. In such a case, set as described below.
1Set the SYNC switch to the L-L position.
2Switch the display on the monitor from camera 1 to camera 2.
Adjust the LINE PHASE volume on camera 2 until the vertical
roll of the image stops.
If more than two cameras are used, please repeat this
procedure for all the cameras.
CAUTION:
If the vertical roll cannot be corrected by setting the LINE PHASE
volume on camera 2, try setting the LINE PHASE volume on
camera 1. If it still cannot be corrected, please check that the
polarity of the power cords of all connected devices is correct.
AGC setting
AGC (Automatic gain control) can be turned ON or OFF.
ON: Auto gain control
OFF: Fixed gain
E. S.
L
E
V
E
L
DC
VIDEO
A. I.
LENS
LH
VR301
ON
123
OFF
ON
L-L
INT
AGCSYNC
ON
OFF
BLC EI
[VCB-3100P]
ON
OFF
ON
E. S.
BLC
L
E
V
E
L
DC
VIDEO
A. I.
LENS
LH
VR301
ON
123
EI
OFF
ON
SYNC
L-L
INT
VR302
AGC
[VCB-3170P]
L-L
INT
OFF
ON
AGC
L73M , N /XE GB 1996, 10, 31
8 English
SETTINGS
High speed electronic shutter setting
Normally, the speed setting switches for the high speed ES
(electronic shutter) are all set to the OFF position. This sets the
electronic shutter speed to 1/ 0 sec. The switches can be set as
indicated in table A to select one of the 8 speeds available.
Model VCB-3170P
When using the high speed electronic shutter, the EI/BLC
switch must be set to the OFF position.
The switches can be set as indicated in table A, to select one of
the 8 speeds available.
Model VCB-3100P
The switches can be set as indicated in table A, to select one of
the speeds (1, 5, 6, 7, 8) available.
CAUTION:
•When using the high speed electronic shutter, the EI/BLC
switch (model VCB-3170P) or the EI and BLC switches (model
VCB-3100P) must be set to the OFF position.
•Using the high speed electronic shutter indoors with low
lighting, will give darker pictures. In such a case, add some
lights to make sure the lighting is sufficient. If the lighting is very
bright, pay attention to the light angle in order to avoid or
minimize the smear phenomenon effect.
Table A
11/50 sec.
21/120 sec.
31/250 sec.
41/500 sec.
51/1000 sec.
61/2000 sec.
71/4000 sec.
81/10000 sec.
ON
123
ON
123
ON
123
ON
123
ON
123
ON
123
ON
123
ON
123
L73M , N /XE GB 1996, 10, 31
English 9
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cámara de seguridad de Sanyo
Sanyo
Sanyo VCC-4374P Manual de usuario
Sanyo
Sanyo VCC-3912 Manual de usuario
Sanyo
Sanyo VCC-WB4000P Manual de usuario
Sanyo
Sanyo VCC-5974P Manual de usuario
Sanyo
Sanyo VCC-6580 Manual de usuario
Sanyo
Sanyo THINK GAIA VCC-HD4600 Manual de usuario
Sanyo
Sanyo VCC-WB2000 Manual de usuario
Sanyo
Sanyo VCB-3384 - 1/3" B/W CCD Camera Manual de usuario
Sanyo
Sanyo VDC-HD3100 - Full HD 1080p Vandal Dome... Manual de usuario
Sanyo
Sanyo VCC-4344 - 1/4" CCD High Performance Day/Night... Manual de usuario
Sanyo
Sanyo VCB-3372 Manual de usuario
Sanyo
Sanyo VDC-HD3100 - Full HD 1080p Vandal Dome... Manual de usuario
Sanyo
Sanyo VCB-3512T Manual de usuario
Sanyo
Sanyo VDC-DP7584S - 1/4" Color CCD Vandal-Resistant Dome... Manual de usuario
Sanyo
Sanyo VDC-D1185VP Manual de usuario
Sanyo
Sanyo VCC-HD5600 - Full HD 1080p Day/Night Pan-Tilt-Zoom... Manual de usuario
Sanyo
Sanyo VCC-P7574 - 1/4" Color CCD Indoor Mini Dome... Manual de usuario
Sanyo
Sanyo VCC-HD5400 Guía del usuario
Sanyo
Sanyo VCC-P9574S - 1/4" CCD Pan-Focus PTZ Dome... Manual de usuario
Sanyo
Sanyo VCC-6584E - 1/3" Color CCD DSP High-Resolution... Manual de usuario
