Sanuvox SRMax Manual de usuario

SRMax Installation Manual

WARNING

READ AND FOLLOW ALL INSTRUCTIONS CONTAINED IN THIS MANUAL BEFORE USE.

FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL

INJURIES OR DAMAGED UNIT.

Installation and servicing of equipment can be hazardous. Only trained and qualied service personnel

should install, repair or service equipment. Follow national and local safety codes.

Always wear safety glasses and work gloves for protection.

SANUVOX TECHNOLOGIES INC. | 146, rue Barr, St-Laurent, Quebec, Canada H4T 1Y4

1-888-SANUVOX www.sanuvox.com

About the SRMax ............................................................... 2

Important Safety Instructions & Warranty..................... 3

Included in the Box............................................................ 4

Available Options ............................................................... 4

Installation Precautions..................................................... 5

Step by Step Installation .................................................... 6

Information from the Status LED .................................... 7

Reset the lamp timer.......................................................... 8

e SRMax is specically designed to destroy biological and chemical contaminants* such as mold, bacteria, viruses,

chemicals, VOCS* and odors* that may be circulated through the HVAC system of your home.

e SRMax is installed in the RETURN (preferred) or SUPPLY plenum of our HVAC system treating the air passing

through the reecting chamber. e actual percentage of destruction obtained is based on percentage of fresh air,

air velocity, the number of passes and specic contaminants to be treated.

For information or recommendations to size appropriately your specic application, please call Sanuvox at 1-888-SANUVOX.

*Only with LMPRGXJ65 UV lamp

Table of Contents

About the SRMax

GENERAL

Installation and servicing of air-conditioning and related equipment can be hazardous due to system pressure

and electrical components. Only trained and accredited service personnel should install, repair or service such

equipment.

Untrained personnel can perform basic maintenance functions such as replacing lamps. All other operations should

be performed by trained service personnel. When working on the SRMax, observe precautions in the literature, tags,

labels attached to the unit and any other safety precautions considered as best practices in the HVAC industry.

For optimal air purication performance, the lamp and reecting chamber should be kept free of dust / residue

deposit and cleaned regularly using mild soaps or alcohol. Always spot test the cleaner to make sure it does not

damage the surface.

Under no circumstances should water be sprayed or splashed onto the SRMax.

SAFETY PRECAUTIONS

CLEANING PRECAUTIONS

WARNING

Before installing or performing maintenance on the unit, TURN OFF and disconnect unit from power source.

Electrical shock may cause personal injuries or possibly death.

Never expose eyes or skin to ultraviolet light from any source. e UV purier MUST be DISCONNECTED

from power source before performing maintenance of service. Personal injury may result.

Do not touch lamp glass without gloves. Reduced performance of lamp may result. Clean lamp aer handling.

e UV lamp contains a small quantity of mercury. If a lamp breaks, clean and dispose of with care.

Use only specied replacement lamps with your unit. Use of an incorrect lamp can result in damage

to the unit and/or lamp and will also void the warranty.

When applicable local regulations comprises more restrictive installation and/or certication requirements,

the aforementioned requirements prevail on those of this document and the installer agrees to conform to these

at his own expense.

When performing installation, servicing or cleaning the UV purier, it is recommended to wear safety glasses

and gloves.

IMPORTANT SAFETY INSTRUCTIONS

NOTICE

UV lamp can be disposed / recycled aer use as any other uorescent lamp.

Contact and follow your local and national authorities’ specic instructions.

Component Warranty

UV lamp 3 years

Ballast 3 years

Electronics (circuit board) 3 years

WARRANTY

e warranty applicable to the dierent components included in your purchase are as per the table below:

Make sure to keep a copy of your proof of purchase in order for the warranty to be valid.

Component Qty

SRMax 1

UV lamp LMPRGXJ65 1

Installation Kit 1

- UV Caution Decal

- Maintenance Decal

- Pair of cotton gloves

- Metal screws for cover (Qty:4)

- Phillips screws for frame (Qty:6)

- 8-32 screws for turbulator (Qty:2)

- Frame

- Turbulator

INCLUDED IN THE BOX

e SRMax you purchased includes the following :

For information or recommendations to size appropriately your specic application, please call Sanuvox at 1-888-SANUVOX.

INSTALLATION GUIDE

Ensure that the site where the SRMax will be located

can be supplied with the necessary power requirements

(120-240V @ 50-60Hz). To nd out the power consump-

tion of the SRMax refer to the marking label on your unit.

Make sure that there is adequate clearance for service.

Any plastic components in direct line-of-sight of the

UV lamp should be shielded from direct UV exposure

with aluminum foil or removed when possible.

e Sanuvox wire-set is Teon coated which makes it

resistant to UV exposure.

e SRMax reecting chamber has to be installed parallel

to the airow with the turbulator upstream to slow

down the air as it moves in front of the UV lamp.

e suggested operating temperature range is 10 to

50°C (50 to 120°F). Operating the SRMax outside this

range will result in decreased performance. For optimal

performance, air temperature moving through the reaction

chamber should be in the range of 15 to 20°C (60 to 70°F).

e SRMax is not weatherproof. Do not install outdoors

WARNING

Follow all the Safety Instructions outlined in this document and respect all local and national codes applicable.

STEP BY STEP INSTALLATION

1. Prepare the SRMax for installation

1.1 Remove the contents from the packaging. Only aer you

have visually inspected the UV lamp should you break the

security seal on the underside of the cardboard sleeve.

1.2 Carefully slide the UV lamp out from the cardboard sleeve.

Be sure to wear the cotton gloves (included)

guaranteeing a clean lamp free from ngerprints. Fingerprints

on the lamp will negatively impact the UV output of the lamp.

1.3 To install the UV lamp, remove the reecting tube

by removing the 4 screws on either side.

1.4 Slide the UV lamp porcelain end-cap (with 4 pins)

through the clamp. Use the wingnut to tighten the clamp

and secure the lamp. Do not over tighten the wingnut as this

could damage /break the UV lamp. Insert the lamp connector

over the 4 pins of the UV lamp.

1.5 Reinstall the reecting tube by making sure that

the turbulator is facing the airow so that it will slow down

the air as it passes in front of the UV lamp.

2. Prepare the duct (return or supply) for installation

2.1 Evaluate the ideal area for installing the air purier.

e reection chamber should always be parallel to the air-

ow. Ensure that the purier will t into the plenum

and position it keeping in mind to minimize plastics exposure

to direct UV light.

2.2 Use the included metal frame to trace the outline onto

the duct. Allow for a 1/8” space around the marking as to

allow the frame to sit properly in the duct. e duct opening

window should have the following dimensions: 8.5” x 5.5”.

2.3 Cut out the window opening onto the duct. Place the frame

into the opening made in the duct and use the 6 metal screws

provided in the installation kit to secure it to the duct.

3. Finalize SRMax installation in the duct

and power ON

3.1 Place the SRMax into the frame, guided with

the alignment pins.

3.2 Secure the SRMax to the frame with the 4 remaining

screws located in the 4 corners of the SRMax cover.

3.3 Use the power cord of the unit to plug into a wall outlet

that provides the power as indicated on the marking label

of the product. An extension cord may be used if there is not

a power outlet close to where the SRMax is installed.

3.4 You are now ready to power ON your new SRMax

and enjoy great air quality for you and your family.

GREEN : In operation

ORANGE : Heartbeat followed by 1 ash - lamp over 3 years that needs to be replaced

BLUE : Heartbeat, stand-by waiting for airow

INFORMATION FROM THE STATUS LED

Normal operation

BLUE : Airow detection activated*

WHITE : Factory setting, airow detection de-activated

At start-up

RED (2 ashes) : Lamp or ballast failure

RED (3 ashes) : ermistor disconnected

RED (4 ashes) : ermistor shorted

Error code **

* Refer to the section below Activating airow detection ** Refer to troubleshooting (sanuvox.com/help)

RESET THE LAMP TIMER

Aer installing the lamp, make sure the timer function is reset.

1. To reset the lamp timer the unit needs to be powered and turned ON. e status LED should either be ‘Green’

or ‘Blue’ (heartbeat).

2. Use a small object similar to a paper clip and insert it into the hole in order to be able to press the reset button.

3. Press and hold the reset button for a minimum of 3 seconds. When releasing the reset button the counter will

be reset.

Replacement parts

Part Number Description

BST120/240GL Ballast with mutli-voltage input of 120 to 240V (50-60Hz)

LMPRGXJ65 T6 Regular Dual Zone (UVC / UVV) 6.5in “J” shape UV lamp

LMPRGJ65 T6 Regular Germicidal (UVC) 6.5in “J” shape UV lamp

ACTIVATING AIRFLOW DETECTION

(OPTIONAL)

e SRMax default factory mode, when the unit

is plugged in and the power switch is ON, will leave

the lamp ON at all times in order to reduce the cycling

strain on the lamp and improve its life.

It is possible to activate the airow detection if required.

e activation procedure is the following:

1. If your unit is powered ON, start by turning OFF

the power switch.

2. Use a small object similar to a paper clip and insert

it into the reset hole in order to be able to press

the reset button.

3. First, turn ON the power switch and then press

the reset button. You have 5 seconds from the moment

the unit is powered ON to press the reset button

to activate the airow detection.

Every time you press the button you will notice that the

LED color will either be “Blue” or “White”. When the

LED is “Blue” the airow detection is activated. Wait 5

seconds for the control circuit to save the setting.

4. From now on, the SRMax will only activate when

airow is detected in your duct system.

Tabla de contenidos

Otros manuales de Purificador de aire de Sanuvox

Sanuvox

Sanuvox S1000 Manual de usuario

Sanuvox

Sanuvox Quattro Manual de usuario

Sanuvox

Sanuvox R1r Manual de usuario

Sanuvox

Sanuvox S1000 Manual de usuario

Sanuvox

Sanuvox SANUVAIR S300 OZD Manual de usuario

Sanuvox

Sanuvox P900 Manual de usuario

Sanuvox

Sanuvox SANUVAIR S100 Manual de usuario

Sanuvox

Sanuvox P900-GX Manual de usuario

Sanuvox

Sanuvox BIOPUR Manual de usuario

Sanuvox

Sanuvox S1000 Manual de usuario

Sanuvox

Sanuvox SANUVAIR S1000 CRO Manual de usuario

Sanuvox

Sanuvox HRV6 Manual de usuario

Sanuvox

Sanuvox SANUVAIR S600 Manual de usuario

Sanuvox

Sanuvox S300 Manual de usuario

Sanuvox

Sanuvox SRMax Manual de programación

Sanuvox

Sanuvox Quattro Manual de usuario

Sanuvox

Sanuvox RMax Ductboard Manual de usuario

Sanuvox

Sanuvox S300FX Manual de usuario

Sanuvox

Sanuvox R MAX Manual de usuario

Sanuvox

Sanuvox Quattro Manual de usuario

Sanuvox

Sanuvox VP900 Manual de usuario

Sanuvox

Sanuvox FOODSAFE IL Manual de usuario

Sanuvox

Sanuvox SANUVAIR S100GX Manual de usuario

Sanuvox

Sanuvox GC S300-G2 Manual de usuario

Manuales populares de Purificador de aire de otras marcas

IKEA

IKEA UPPÅTVIND Manual de usuario

Nash

Nash AP-1 PureSmart Manual de usuario

LG PH-U450 Series Manual de usuario

DeLonghi

DeLonghi DDSX 220WFA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MA-E85R-E Manual de usuario

Sharp

Sharp FU-40SE Manual de usuario

Philips

Philips AC2721 Manual de usuario

Hitachi

Hitachi EP-A3000 Manual de usuario

TruSens

TruSens Z-2000 Manual de usuario

Motorola

Motorola MBP87SN Manual de usuario

Beko

Beko ATP 7100I Manual de usuario

Carrier

Carrier INFINITY 1620 Manual de usuario

AtmosAir

AtmosAir P2002 Manual de usuario

Winix

Winix NK300 Manual de usuario

Friedrich

Friedrich C-90A Instrucciones de funcionamiento e instalación

Surgically Clean Air

Surgically Clean Air JADE2.0 Manual de usuario

Base aire

Base aire 555 Pro Manual de usuario

Champion

Champion CP25 Manual de usuario