Sanuvox S300 Manual de usuario

S300 VOC FOR SMOKING ROOM

INSTALLER INSTRUCTIONS

For a 2400 cubic feet maximum smoking room

Box contains:

• One (1) S300 VOC unit that includes:

o One (1) ‘’J’’ lamp UVC/UVV with yellow tips (part LMPHGXJ105-1 2’’ exposé)

o One (1) ‘’J’’ lamp all UVV with blue tips (part LMPHXJ105)

o Two (2) Multi voltage ballasts (part BST120/277GL) and 2 lamp-holding brackets

o One (1) Relay (part MSCELC16) connected to the all UVV lamp

o Twenty (20) feet of wire that can be inserted in BX shield.

o One (1) VOC controller (part MSC1A) factory’s pre-set

• Two (2) replacement pre-filters (part MSCFTR10)

LAMP INSTALLATION

1. Remove the 6 screws on the front cover (The one with

the SANUVOX logo). Put aside.

2. Remove the BLUE END CAP lamp from packaging. Use

the gloves provided.

3. Insert the lamp in the second clamp and tighten.

(furthest clamp from opening)

4. Holding the cap with one hand, plug the white

connector tightly on the lamp

5. Remove the YELLOW END CAP lamp from packaging.

Use the gloves provided.

6. Insert the lamp in the first clamp and tighten. (closest to

opening)

7. Holding the cap with one hand, plug the white

connector tightly on the lamp

8. Put the cover back on with the 6 screws

Controller

Casing

Wiring 20’

Relay

GENERAL INSTALLATION

Unit could be

• Suspended from ceiling with

angles and suspension rods (not

included).

• Hung on wall with supplied angle

iron (included).

Using 8’’ collars, attach rigid or flex duct to the return side of

the unit above the area where smoke accumulates in order to

remove as much smoke as possible. Attach duct (metal or flex)

to the supply side of the unit to discharge clean air over door

or entryway. This is done to prevent odors from escaping the

room. It is through recirculation that the odors will be

removed. If the room is longer , you may use multiple inlets

to pull the smoke to the unit.

The VOC controller should be installed on the wall, at 12 inches from the ceiling where the smoke

accumulates. The S300 VOC unit comes with 20ft of wire to link the controller box to the unit. If 20 ft

not long enough, you can replace it with BX wiring with 3 wires.

WORKING INSTRUCTION

The VOC controller analyzes the air every 90 seconds. A 20-foot power cord connects it via a relay to

the device to activate the second oxidizing lamp on demand.

The S300 unit runs continuously, so its regular lamp purifies the air constantly. This dual zone lamp

(UVC / UVV) is enough when there are only one or two smokers.

However, when the cigarette smoke increases in the room, the VOC controller that samples the air

at regular intervals, then triggers the 2nd UVV lamp for periods of 90 seconds. This cycle is repeated

if the controller detects smoke in the room: it then turns off the 2nd lamp, leaving the 1st lamp to

continue the cleaning cycle.

SIMPLIFIED PROCESS:

• Ashes in the “white” smoke will be trapped onto the filter

• Nicotine molecules will be dried by the UVC rays than trapped in the filters without the tar like

material that coats everything.

• VOC will be oxidised by the UVV, reducing substantially their olfactory perception.

Suggested installation

VOC CONTROLLER

Remove the cover.

Connect the 3 wires from the controller to the same color

wiring coming from the unit. Use the wire connectors

included.

The detector is factory set a t 3.0 V DC; If you wish to set up a

higher sensitivity, please proceed as follow.

SETTING (if necessary)

You will need a voltmeter with alligator type probes.

Place the probes one on the positive terminal, the other on

the neutral terminal.

Use a small screwdriver to turn the adjustment screw to increase the sensitivity of the controller.

The default setting is 3.0 v dc. The closer your setting is to 3.0 vdc, the faster the triggering of the lamp

will be.

CHECKING IF IT WORKS

1. Start the unit: inside the polycarbonate box, the GREEN LED flashes. It will take some time, so

the electronic board initializes itself.

2. After 5 minutes, the GREEN LED will turn solid. Blow some cigarette smoke into the controller. If

the other RED LED lights up, the relay triggers on the oxidizing lamp (all UVV). This sequence

reproduce itself every minute or so. When there is no more smoke (VOC), the RED LED is turned

off at the same time as the lamp.

MAINTENANCE INSTRUCTIONS

• MONTHLY: Change the pre-filter that protects the motor (part # MSCFTR10) to ensure the

optimal performance of the unit. Check the lamps: if there is a cloudy residue please clean then

off with denatured alcohol.

• YEARLY: Change lamps (parts -see below) to maintain performance: make sure to put the same

lamp in the same clamp. Do not interchange the lamps as the blue end cap lamp works only with

the VOC controller.

o LMPHGXJ105-1 lamp UVC/UVV 2’’ exposed (yellow end cap)

o LMPHXJ105 lamp all UVV (blue end cap)

• 3-5 years: Change VOC controller board

setting screw:

triggers at

3.0 V DC

Positive

Neutral

Sensor

S300 VOC FOR SMOKING ROOM

USER INSTRUCTIONS

MAINTENANCE

• MONTLY:

o Check filter: if filters are dirty, change them (part # MSCFTR10). This will help lower air

restrictions so to keep up the performance of the unit.

o Check if the lamps are covered with dust; in that case, clean them with denatured

alcohol and a clean cloth.

• ANNUALLY:

o Change lamps (parts -see below) to maintain performance: make sure to put the same

lamp in the same clamp. Do not interchange lamps as the blue end cap lamp works only

with the VOC controller.

§ LMPHGXJ105-1 lamp UVC/UVV 2’’ exposed (yellow end cap)

§ LMPHXJ105 lamp all UVV (blue end cap)

• 3-5 years: Change VOC controller board

WORKING INSTRUCTIONS

• The VOC controller analyzes the air every 90 seconds. A 20-foot power cord connects it via a

relay to the device to activate the second oxidizing lamp on demand.

• The S300 VOC unit runs continuously, so its regular lamp purifies the air constantly. This

dual zone lamp (UVC / UVV) is enough when there are only one or two smokers.

• However, if there is much smoke in the room, the VOC controller, that samples the air on a

regular basis, will then trigger the second all UVV lamp for a period of 90 seconds. This cycle

will repeat itself until there is no more smoke in the room: the second lamp will then shut

off, leaving the first lamp on doing the work

SIMPLIFIED PROCESS:

• Ashes in the “white” smoke will be trapped onto the filter

• Nicotine molecules will be dried by the UVC rays than trapped in the filters without the tar like

material that coats everything.

• VOC will be oxidised by the UVV, reducing substantially their olfactory perception.

It is very important that the fan processes the air rapidly.

Changing the filters regularly is a must.

Otros manuales para S300

Tabla de contenidos

Otros manuales de Purificador de aire de Sanuvox

Sanuvox

Sanuvox VP900 Manual de usuario

Sanuvox

Sanuvox S300 Manual de usuario

Sanuvox

Sanuvox S1000 Manual de usuario

Sanuvox

Sanuvox P900 Manual de usuario

Sanuvox

Sanuvox SRMax Manual de programación

Sanuvox

Sanuvox SANUVAIR S600 Manual de usuario

Sanuvox

Sanuvox SANUVAIR S100 Manual de usuario

Sanuvox

Sanuvox S300 Manual de usuario

Sanuvox

Sanuvox P900-GX Manual de usuario

Sanuvox

Sanuvox SRMax Manual de usuario

Sanuvox

Sanuvox S300 Manual de usuario

Sanuvox

Sanuvox R1r Manual de usuario

Sanuvox

Sanuvox FOODSAFE IL Manual de usuario

Sanuvox

Sanuvox SANUVAIR S1000 CRO Manual de usuario

Sanuvox

Sanuvox RMax Ductboard Manual de usuario

Sanuvox

Sanuvox R MAX Manual de usuario

Sanuvox

Sanuvox HRV6 Manual de usuario

Sanuvox

Sanuvox SANUVAIR S100GX Manual de usuario

Sanuvox

Sanuvox Quattro Manual de usuario

Sanuvox

Sanuvox S1000 Manual de usuario

Sanuvox

Sanuvox GC S300-G2 Manual de usuario

Sanuvox

Sanuvox BIOPUR Manual de usuario

Sanuvox

Sanuvox Quattro Manual de usuario

Sanuvox

Sanuvox S1000 Manual de usuario

Manuales populares de Purificador de aire de otras marcas

IKEA

IKEA UPPÅTVIND Manual de usuario

Nash

Nash AP-1 PureSmart Manual de usuario

LG PH-U450 Series Manual de usuario

DeLonghi

DeLonghi DDSX 220WFA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MA-E85R-E Manual de usuario

Sharp

Sharp FU-40SE Manual de usuario

Philips

Philips AC2721 Manual de usuario

Hitachi

Hitachi EP-A3000 Manual de usuario

TruSens

TruSens Z-2000 Manual de usuario

Motorola

Motorola MBP87SN Manual de usuario

Beko

Beko ATP 7100I Manual de usuario

Carrier

Carrier INFINITY 1620 Manual de usuario

AtmosAir

AtmosAir P2002 Manual de usuario

Winix

Winix NK300 Manual de usuario

Friedrich

Friedrich C-90A Instrucciones de funcionamiento e instalación

Surgically Clean Air

Surgically Clean Air JADE2.0 Manual de usuario

Base aire

Base aire 555 Pro Manual de usuario

Champion

Champion CP25 Manual de usuario