Sanus FPA400 Manual de usuario
FPA400 INSTRUCTION MANUAL
Scan for easy install video
san.us/260
We’ll Make It Stress-Free
If you have any questions along the way, just give us a call.
1-888-333-9952. We’re ready to help!
2
IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS – PLEASE READ ENTIRE MANUAL PRIOR TO USE
Before You Begin
Please check the following items:
Any accessories you plan to use do not exceed the specified weight limit.
The wall you chose to mount your shelf is wood stud, drywall, solid concrete, or concrete block.
You read and understand these directions.
You have the tools needed for installation.
If you do not understand these instructions, or have doubts about the safety of the installation, assembly or use of this product, contact
Customer Service or call a qualified contractor.
CAUTION: Avoid potential personal injuries and property damage!
●Do not use this product for any purpose not explicitly specified by manufacturer.
●Do not place objects heavier than 15 lb (6.8 kg) on shelf.
●Do not place a TV on shelf.
●Do not allow children to climb or hang on shelf.
●Manufacturer is not responsible for damage or injury caused by incorrect assembly or use.
●This product is designed for use in wood stud, drywall, solid concrete and concrete block walls.
NOTE: Para instrucciones en Español, ver páginas 16-19
3
Tools Needed
10 mm
(3/8 in.)
11 mm
(7/16 in.)
3 mm
(1/8 in.)
10 mm
(3/8 in.)
Weight Limit
15 lb (6.8 kg)
DO NOT EXCEED!
Features
Can be mounted to drywall, wood stud, or concrete.
Stackable to accommodate multiple components - not to exceed
15 lb (6.8 kg) on each shelf.
4
NOTE: Not all hardware included will be used.
Supplied Parts and Hardware
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged
item to your dealer; contact Customer Service. Never use damaged parts!
Parts and Hardware for STEP 1 Parts and Hardware for STEP 2
Lag Bolts and Wall Screws Washer Wall Plate
Wall Anchors
01
02
04
05
09
10 11
03
(1)
(3)
(3)
(1)
(1)
(1) (1)
(2) (2)
(1)
(1)
06
07
08
1/4 x 2 ½ in.
#8 x 2 in.
M5 x 20 M5 x 6
M3
5
Dimensions
Single shelf configuration
1.11
28.1
6.3
159.9
12.50
317.5
17.00
431.8
Stacked configuration
1.11
28.1
5.11
129.8
6.3
159.9
12.50
317.5
17.00
431.8
in.
[mm]
6
Attach the Wall Plate to the Wall
-
Wood Stud Option
1 2
≤ 16 mm
(5/8 in.)
06
STEP 1
IMPORTANT: For stacking configurations, stack from the top down.
1. Locate your stud(s). Verify the center of the stud using an awl, a thin nail, or an edge to edge stud finder.
CAUTION: Avoid potential personal injuries and property damage!
●Drywall covering the wall must not exceed 16 mm (5/8 in.).
●Minimum wood stud size: common 51 x 102 mm (2 x 4 in.) nominal 38 x 89 mm (1½ x 3½ in.).
2. Remove the front (F) and top (T) covers from the wall plate 06 . Level the wall plate 06 and mark the hole locations.
(F)
(T)
7
3 4
06
63.5 mm
(2½ in.)
3 mm
(1/8 in.)
02
01
03
STEP 1
3. Drill pilot holes.
IMPORTANT: Pilot holes must be drilled to a depth of 63.5 mm (2½ in.), using a 3 mm (1/8 in.) diameter drill bit.
4. Tighten the lag bolt 01 and washer 03 the screw 02 only until they are pulled firmly against the wall plate 06 .
CAUTION: Improper use could reduce the holding power of the lag bolt and screw. DO NOT over-tighten the lag bolt and
screw.
8
1 2
STEP 1
Attach the Wall Plate to the Wall -
Solid Concrete or Concrete Block Option
IMPORTANT: For stacking configurations, stack from the top down.
Remove the front (F) and top (T) covers from the wall plate 06 .
1. Level the wall plate 06 and mark the hole locations. Level the wall plate 06 and mark the hole locations.
CAUTION: Avoid potential personal injuries and property damage!
●Mount the wall plate 06 directly onto the concrete surface
●Minimum solid concrete thickness: 203mm (8 in.)
●Minimum concrete block size: 203 x 203 x 406 mm (8 x 8x 16 in.)
2. Drill pilot holes.
IMPORTANT: Pilot holes must be drilled to a depth of 75 mm (3 in.), using a 10 mm (3/8 in.) diameter drill bit. Never drill into the
mortar between blocks.
06
(F)
(T)
9
3. Insert anchors 04 and 05 .
CAUTION: Be sure the anchors are seated flush with the concrete surface.
4. Tighten the lag bolt 01 and washer 03 the screw 02 only until they are pulled firmly against the wall plate 06 .
CAUTION: Improper use could reduce the holding power of the lag bolt and screw. DO NOT over-tighten the lag bolt and
screw.
34
06
04
05 03
01
02
04
STEP 1
10
1 2
06
Attach the Wall Plate to the Wall -
Drywall Option
STEP 1
IMPORTANT: For stacking configurations, stack from the top down.
Remove the front (F) and top (T) covers from the wall plate 06 .
1. Level the wall plate 06 and mark the hole locations.
CAUTION:
Avoid potential injuries or property damage!
●Mount the wall plate 06 directly onto the wall.
●Drywall covering the wall must not exceed 13mm (1/2 in.).
●Do not install anchors into the seam between drywall pieces.
2. Drill pilot holes.
IMPORTANT: Pilot holes MUST be drilled to a depth of 38 mm (1½ in.) using a 10 mm (3/8 in.) diameter drill bit.
(F)
(T)
Tabla de contenidos
Idiomas:
Otros manuales de Soporte de TV de Sanus
Sanus
Sanus VLF220 Manual de usuario
Sanus
Sanus VLT7-B2 Manual de usuario
Sanus
Sanus Classic MSF07 Manual de usuario
Sanus
Sanus VSF409 Manual de usuario
Sanus
Sanus FTVS1 Manual de usuario
Sanus
Sanus VLF613 Manual de usuario
Sanus
Sanus CLASSIC MLT14 Manual de usuario
Sanus
Sanus LLT1 Manual de usuario
Sanus
Sanus VMD2 Manual de usuario
Sanus
Sanus VLF525 Manual de usuario
Sanus
Sanus VXT7-B2 Manual de usuario
Sanus
Sanus BMT1 Manual de usuario
Sanus
Sanus VMCA10 Manual de usuario
Sanus
Sanus VML44A Manual de usuario
Sanus
Sanus VLF515 Manual de usuario
Sanus
Sanus VLF320 Manual de usuario
Sanus
Sanus 65PFL5604/F7 Manual de usuario
Sanus
Sanus BML1 Manual de usuario
Sanus
Sanus New VisionMount LF228-B1 Manual de usuario
Sanus
Sanus New VisionMount VLL10-B1 Manual de usuario
