Sanus VF3012 Manual de usuario
MODEL VF3012 INSTRUCTION MANUAL
Scan here to learn more
about your product online
We’ll Make It Stress-Free
If you have any questions along the way, just give us a call.
1-800-359-5520. We’re ready to help!
2
Specifications
Weight capacity-DO NOT EXCEED: 9 kg (20 lb) per shelf or a combined weight of 13.6 kg (30 lb).
Before You Begin
CAUTION: Avoid potential personal injuries and property damage!
●TheVF3012 is designed to support audio and video accessory equipment; it is NOT designed
to support a television.
●Do not use this product for any purpose not explicitly specified by manufacturer.
●The wall must be capable of supporting five times the weight of the shelf and components
combined.
●This product is designed for use in wood stud, drywall, solid concrete, and concrete block
walls.
●This product is not designed for use in metal stud walls!
●Manufacturer is not responsible for damage or injury caused by incorrect assembly or use.
●If you do not understand these instructions, or have doubts about the safety of the
installation, assembly or use of this product, contact Customer Service or call a qualified
contractor.
IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS – PLEASE READ ENTIRE MANUAL PRIOR TO USE
DO NOT mount the top shelf higher than
99 cm (39 in.) above the floor.
99cm
39 in.
CAUTION: Tempered glass has been chosen for this product because of its strength and
safety characteristics. However, tempered glass should still be handled with care to avoid
possible property damage or personal injury.
●Mishandling during shipping, assembly, or use may result in damage that can weaken the
tempered glass.
●Periodically check the glass to look for chips, cracks, or deep scratches.
●If chips, cracks, or deep scratches are found, discontinue use and contact customer
service.
3
Dimensions
406.4 mm
(16 in.)
457 mm
(18 in.)
439 mm
(17.29 in.)
203 mm
(8 in.)
ADJUSTABLE
386.6 mm
(15.22 in.)
406.4 mm
(16 in.)
457 mm
(18 in.)
386.6 mm
(15.22 in.)
140.4 mm
(4.74 in.)
203 mm
(8 in.)
ADJUSTABLE
439 mm
(17.29 in.)
Required Tools
13 mm
(1/2 in.)
5.5 mm
(7/32 in.)
10 mm
(3/8 in.)
4
M7 x 70mm
M4
1/4-20 x 1 ¾ in.
1/4-20
Supplied Parts and Hardware
Parts and Hardware for STEP 1
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to
your dealer; contact Customer Service. Never use damaged parts!
NOTE: Not all hardware included will be used.
Wall Plate
Drywall Bolts
M4 Driver Bit
01 (1)
05 (3)
Concrete Anchors
04 (3)
03 (1)
Wood and Concrete Lag Bolts
02 (3)
Drywall Anchors
06 (3)
5
M4
1/4-20 x18 mm
1/4-20 x 5/8 in.
1/4 in.
Parts and Hardware for STEP 2 Parts and Hardware for STEP 3
Parts for STEP 4
07 (2) 08 (2)
Shelf Supports Glide Locks
Glide Lock Screws
09 (4)
10 (1)
M4 Hex Key
11 (2)
14 (4)
Glass Shelves
Shelf Screws
Shelf Washers
13 (4)
Shelf Sleeves
12 (2)
15 (1) 16 (1)
Top Cap Bottom Cap
6
Attach the Wall Plate to the Wall
-
Wood Stud Option
1 2
STEP 1
1. Locate your stud(s). Verify the center of the stud using an awl, a thin nail, or an edge to edge stud finder.
CAUTION: Avoid potential personal injuries and property damage!
●Drywall covering the wall must not exceed 16 mm (5/8 in.).
●Minimum wood stud size: common 51 x 102 mm (2 x 4 in.) nominal 38 x 89 mm (1½ x 3½ in.).
2. Level the wall plate 01 and mark the hole locations.
≤ 16 mm
(5/8 in.)
01
7
3 4
63.5 mm
(2½ in.)
5.5 mm
(7/32 in.)
3. Drill pilot holes.
IMPORTANT: Pilot holes must be drilled to a depth of 63.5 mm (2½ in.), using a 5.5 mm (7/32 in.) diameter drill bit.
4. Using the bit driver 03 tighten the lag bolts 02 only until they are pulled firmly against the wall plate 01 .
CAUTION: Improper use could reduce the holding power of the lag bolts 02 . DO NOT over-tighten the lag bolts 02 .
01
03
02
STEP 1
8
Attach the Wall Plate to the Wall -
Solid Concrete or Concrete Block Option
12
STEP 1
1. Level the wall plate 01 and mark the hole locations.
CAUTION: Avoid potential personal injuries and property damage!
●Mount the wall plate 01 directly onto the concrete surface
●Minimum solid concrete thickness: 203mm (8 in.)
●Minimum concrete block size: 203 x 203 x 406 mm (8 x 8x 16 in.)
2. Drill pilot holes.
IMPORTANT: Pilot holes must be drilled to a depth of 75 mm (3 in.), using a 10 mm (3/8 in.) diameter drill bit. Never drill into the mortar
between blocks.
01
9
3. Insert anchors 04 .
CAUTION: Be sure the anchors 04 are seated flush with the concrete surface.
4. Using the bit driver 03 tighten the lag bolts 02 only until they are pulled firmly against the wall plate 01 .
CAUTION: Improper use could reduce the holding power of the lag bolts 02 . DO NOT over-tighten the lag bolts 02 .
3 4
01
04
04
02
03
75 mm
(3 in.)
STEP 1
10
1
2
>13 mm
(1/2 in.)
01
1. Level the wall plate 01 and mark the hole locations.
CAUTION:
Avoid potential injuries or property damage!
●Mount the wall plate 01 directly onto the wall.
●Drywall covering the wall must be at least 13 mm (1/2 in.) thick.
●Do not install anchors into the seam between drywall panels.
2. Drill pilot holes.
IMPORTANT: Pilot holes MUST be drilled to a depth of 38 mm
(1½ in.) using a 13 mm (1/2 in.) diameter drill bit.
STEP 1
Attach the Wall Plate to the Wall -
Drywall Option
Tabla de contenidos
Otros manuales de Rack y soporte de Sanus
Sanus
Sanus VST15 Manual de usuario
Sanus
Sanus WMS3 Manual de usuario
Sanus
Sanus WSSATM1 Manual de usuario
Sanus
Sanus DLT1 Manual de usuario
Sanus
Sanus CFR2100 Series Manual de usuario
Sanus
Sanus VML5 Manual de usuario
Sanus
Sanus F107 Manual de usuario
Sanus
Sanus VSL4 Manual de usuario
Sanus
Sanus VTM27 Instrucciones de instalación
Sanus
Sanus CFR1610 Manual de usuario
Sanus
Sanus VisionMount VMPR1 Manual de usuario
Sanus
Sanus BFAV344 Manual de usuario
Sanus
Sanus SLT2 Manual de usuario
Sanus
Sanus VLL5 Manual de usuario
Sanus
Sanus BSSATM1 Manual de usuario
Sanus
Sanus SLF9 Manual de usuario
Sanus
Sanus VisionMount VMPl50A Manual de usuario
Sanus
Sanus VMF518 Manual de usuario
Sanus
Sanus SMF218-B8 Manual de usuario
Sanus
Sanus 6901-170053 Manual de usuario
