Sanus Systems VM2 Manual de usuario

Assembly Instructions for Model: VM2

Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 6.24.05

Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com

Thank you for choosing Sanus Systems Vision Mount. This product is designed to

mount VESA 75/100 compatible LCD televisions up to 30 pounds onto a vertical wall.

It allows you to effortlessly tilt and swivel your new television up to 15° in either

direction as well as extend it up to 9” away from the wall without the use of tools.

Check carefully to make sure there are no missing or defective parts. Never use defec-

tive parts. Improper installation may cause damage or serious injury. If you do not

understand these directions, or have any doubts about the safety of the installation,

please call a qualied contractor or contact Sanus at 800.359.5520 or www.sanus.com.

We can quickly assist you with installation questions and missing or damaged parts.

Replacement parts for Sanus products purchased through authorized dealers will be

shipped directly to you.

Required Tools: Drill with 3/16” bit, 5/16” drill bit, Phillips screw driver

Parts and Hardware: *Not shown as actual size

(1) Allen Key - b

(1) Monitor Mount - a* (1) Wall Plate - c*

(2) Lag Bolt - d

(4) M4 x 10 Bolt - e (4) Knob Replacement Bolt - f (2) 3/4” Furniture Bolts - g (2) 1 1/8” Furniture Bolt - h (2) Cabinet Mount Insert - i

(1) Cap - k (1) Small Washer - l

(1) Large Washer - j (1) Knob - m

Step 1 - Attaching to the Television: Attach the Monitor Mount (a) to the back of your LCD television using the M4 x 10 Bolt (e) as shown in Diagram 1. Place 4 bolts through the

Monitor Mount and tighten snugly into the VESA bolt mounting pattern on the back of the television. Make sure the large side of the tapered hole on the Monitor Mount faces toward

the bottom of the television.

Step 2a - Attaching under a cabinet: Use the Wall Plate (c) as a template to mark the desired location of the two mounting holes under the cabinet. Pre-drill the two holes with a

5/16” drill bit. Place the Cabinet Mount Inserts (i) down through the mounting surface as shown in Diagram 2a. Attach the Wall Plate using either Cabinet Mount Bolt (g or h) depending

on the thickness of the surface. Tighten bolts with the Allen Key (b) until they are snug. See Diagram 2a for assistance.

Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 6.24.05

Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com

Diagram 1 Diagram 2

Detailed View

Diagram 3

Diagram 2a Diagram 2b

i d l

square cut in cap

h g

square end of

bushing

c c

Step 2b - Attaching to the Wall: Hardware for wood stud mounting is provided.

For all other mounting applications contact a local contractor or hardware store. Use

a high quality stud sensor to locate a stud. It is a good idea to verify the stud location

with an awl or thin nail as shown in Diagram 2. Use the Wall Plate (c) as a template to

mark the two hole locations on the wall. Make sure these holes are aligned vertically

and centered over the stud. Pre-drill the two holes to a depth of 2.5” using a 3/16” drill

bit. Attach the Wall Plate to the wall using the two Lag Bolts (d) as shown in Diagram

2b. Tighten the Lag Bolts rmly with the Allen Key (b).

Step 3 - Add Monitor Mount to Wall Plate: Once the LCD TV is attached to the

Monitor Mount (a), and the Wall Plate (c) is properly installed, set the tapered hole in

the Monitor Mount down over the cone shaped bushing on the Wall plate. This process

is shown without the TV in Diagram 3 so that you can see the parts more clearly. Make

sure the Monitor Mount is seated completely onto the Wall Plate. Add the Large Washer

(j). Next add the Cap (k). Make sure the square cut into the cap ts over the square top

of the Wall Plate bushing. Finally place the Knob (m) through the Small Washer (l), the Cap and into the cone shaped bushing. You can now set each of the knobs to the desired level of

tension.

Note: For institutional or heavy load applications a Knob Replacement bolt (f) may be used in place of each Knob and tightened with the Allen Key provided.

This will allow you to get greater tension while still being able to adjust the position of your TV.

Otros manuales para VM2

Tabla de contenidos

Otros manuales de Rack y soporte de Sanus Systems

Sanus Systems

Sanus Systems VisionMount VMCA7 Manual de usuario

Sanus Systems

Sanus Systems Wall Mount LL22 Manual de usuario

Sanus Systems

Sanus Systems VMPR1 Manual de usuario

Sanus Systems

Sanus Systems WMS2 Manual de usuario

Sanus Systems

Sanus Systems PFV36SB-01 Guía de instalación

Sanus Systems

Sanus Systems VMCC1 Guía de instalación

Sanus Systems

Sanus Systems VMSA Manual de usuario

Sanus Systems

Sanus Systems SANA1A Manual de usuario

Sanus Systems

Sanus Systems Euro Series Manual de usuario

Sanus Systems

Sanus Systems New VisionMount VMA201 Manual de usuario

Sanus Systems

Sanus Systems Wall Mount LL22 Manual de usuario

Sanus Systems

Sanus Systems VM400 Manual de usuario

Sanus Systems

Sanus Systems Sanus Ultimate Foundations UF34 Manual de usuario

Sanus Systems

Sanus Systems VMCA9 Manual de usuario

Sanus Systems

Sanus Systems Sanus VisionMount LRF118-B1 Manual de usuario

Sanus Systems

Sanus Systems VMFL1 Manual de usuario

Sanus Systems

Sanus Systems Platinum Furniture PFV36sb-01 Manual de usuario

Sanus Systems

Sanus Systems SD115 Manual de usuario

Sanus Systems

Sanus Systems VisionMount VMPL2 Manual de usuario

Sanus Systems

Sanus Systems PFFP Manual de usuario

Sanus Systems

Sanus Systems HTB7 Manual de usuario

Sanus Systems

Sanus Systems WMS3 Manual de usuario

Sanus Systems

Sanus Systems PFV60-B1 Manual de usuario

Sanus Systems

Sanus Systems SD103 Manual de usuario

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario