Sanus Systems BF16 Manual de usuario

Assembly Instructions for Basic Foundations: BF16, BF24, BF31

Thank you for choosing Sanus Systems Basic Foundations. Please check carefully to make sure there are no missing or defective parts.

Never use defective parts. Improper assembly may cause damage or serious injury. If you have any questions regarding this product,

contact Sanus at 800.359.5520 or visit www.sanus.com. Our customer service representatives can quickly assist you with missing or

damaged parts. Replacement parts for Sanus products purchased through authorized dealers can be shipped directly to you. Please call

Sanus Systems before returning products to the point of purchase.

Required Tools: Phillips Screw Driver.

Step 1: Check carefully to make sure all parts and hardware are accounted for.

Diagram 1: Parts and Hardware

(8) Isolation Pads - a (16) Screws - b (8) Carpet Spikes - c

(2) Base - d (2) Top Plate - e

For BF16 & BF24: (2) Wire cover - g

(4) Pillar - f For BF31: (4) Wire Cover - g

Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 1.20.05

Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com

Step 2: Assemble Pillars to Base

Using the Screws (b), allign the countersunk holes in the Base

(d) with the corresponding holes in each Pillar (f). The rounded

or beveled edge of the Pillars should face the front of the stand

as shown in Diagram 2. Proceed to tighten all 4 screws by hand

with a phillips screw driver.

Note: Do NOT use any power drivers to tighten the Screws!

Step 3: Add Top Plate to Pillars

Allign the Top Plate (e) with the Pillars (f) so that the two coun-

tersunk holes that are closer together are toward the front of the

stand. Proceed to attach the Top Plate to the Pillars by threading

a Screw (b) through each of the countersunk holes and into the

Pillar as shown in the Detailed View Diagram 3. Tighten the

Screws with a phillips screw driver.

Note: Do NOT use any power drivers to tighten the Screws!

Step 4: Add Isolation Pads and Carpet Spikes

The Isolation Pads (a) are self adhesive. For the best stabil-

ity, place them in the extreme corners of each Top Plate (e) as

shown in Detailed View A of Diagram 4.

Carpet Spikes (c) are provided to stabilize the stand on carpet-

ing and to reduce resonance. Simply insert the end of the Carpet

Spike into each small hole in the bottom side of the Base (d).

You may need to tap them in with a wooden or rubber mallet.

See Detailed View B Diagram 5 for assistance.

Note: The end of the Carpet Spikes may be sharp enough

to dimple or dent wood ﬂoors or furniture. All small objects

can be hazardous to children. The use of Carpet Spikes is

optional. Sanus Systems is not liable for damage or injury.

Step 5: Add Wire Covers

Set the speaker on the stand and run the speaker wire between

the Pillars and through the hole in the base. Snap the plastic

Wire Covers (g) into the Grooves in the Pillars. See the Top

View Diagram 5 for assistance.

Note: Each BF31 stand requires two Wire Covers to span

the full height of the stand.

Diagram 2 Detailed View

Diagram 3 Detailed View

Detailed View A

Diagram 4

a e

Detailed View B

c d

Diagram 5 Top View

wire management

hole

Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 1.20.05

Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Rack y soporte de Sanus Systems

Sanus Systems

Sanus Systems VisionMount MF203 Manual de usuario

Sanus Systems

Sanus Systems VMPL50 Manual de usuario

Sanus Systems

Sanus Systems VMCC1 Guía de instalación

Sanus Systems

Sanus Systems VMCA9 Manual de usuario

Sanus Systems

Sanus Systems Platinum Furniture PFV36sb-01 Manual de usuario

Sanus Systems

Sanus Systems PFV60-B1 Manual de usuario

Sanus Systems

Sanus Systems Monitor Mount VMTV Manual de usuario

Sanus Systems

Sanus Systems VisionMount MT25 Manual de usuario

Sanus Systems

Sanus Systems WMS5 Manual de usuario

Sanus Systems

Sanus Systems New VisionMount VMA201 Manual de usuario

Sanus Systems

Sanus Systems VMSA Manual de usuario

Sanus Systems

Sanus Systems WMS3 Manual de usuario

Sanus Systems

Sanus Systems VisionMount MF202 Manual de usuario

Sanus Systems

Sanus Systems HTSAT Manual de usuario

Sanus Systems

Sanus Systems Sanus Ultimate Foundations UF34 Manual de usuario

Sanus Systems

Sanus Systems VisionMount VMPL2 Manual de usuario

Sanus Systems

Sanus Systems Vision Mount VMBR Manual de usuario

Sanus Systems

Sanus Systems FM37 Manual de usuario

Sanus Systems

Sanus Systems SANA1A Manual de usuario

Sanus Systems

Sanus Systems PFFP Manual de usuario

Sanus Systems

Sanus Systems WMS2 Manual de usuario

Sanus Systems

Sanus Systems Wall Mount LL22 Manual de usuario

Sanus Systems

Sanus Systems VMAV Manual de usuario

Sanus Systems

Sanus Systems Wall Mount LL22 Manual de usuario

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario