Samsung NE58R9311 Manual de usuario

Electric Range

installation manual

imagine the possibilities

Thank you for purchasing this Samsung product.

Install_NE58H9970WS_AA_AC_DG68-00594B-00_EN+CFR.indb 1 6/7/2019 12:45:41 PM

contents

PREPARING TO INSTALL THE

RANGE

3 About this section

3 For your safety

4 Remove packaging

4 Prepare tools & Parts

5 Checking the installation site

7 To avoid breakage

CONNECTING THE POWER

8 Step 1. Meeting electrical

connection requirements

9 Step 2.Accessing the power cord

connection

10 Step 3. Installing the power cord

13 Step 4. Installing the conduit

16 Step 5. Replacing the access cover

INSTALLING THE RANGE

17 Installing the anti-tip device

19 Finalizing the installation

English - 2

Install_NE58H9970WS_AA_AC_DG68-00594B-00_EN+CFR.indb 2 6/7/2019 12:45:41 PM

preparing to install the range

ABOUT THIS SECTION

READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY.

Important note to the installer

• Read all instructions contained in these installation instructions before installing

the range.

• Remove all packing materials from the oven compartments before connecting the

electrical supply to the range.

• Observe all governing codes and ordinances.

• Be sure to leave these instructions with the consumer.

Important note to the consumer

Keep these instructions for the local electrical inspector’s use.

• As when using any appliance generating heat, there are certain safety precautions

you should follow.

• Be sure your range is installed and grounded properly by a qualiﬁed installer or

service technician.

• Make sure the wall coverings around the range can withstand the heat generated

by the range.

• To eliminate the need to reach over the surface elements, avoid having cabinet

storage space above the cooktop.

• The range should not be placed on a base.

FOR YOUR SAFETY

WARNING

WARNING If the information in this manual is not followed exactly, a

ﬁre or electrical shock may result causing property damage, personal injury, or death.

WARNING

WARNING Before beginning the installation, switch the power o at

the service panel and lock the service disconnecting switch to prevent power from being

switched on accidentally. When the service disconnecting switch cannot be locked,

securely fasten a prominent warning device, such as a tag, to the service panel.

WARNING

WARNING This appliance must be properly grounded.

English - 3

01 PREPARING TO INSTALL THE RANGE

Install_NE58H9970WS_AA_AC_DG68-00594B-00_EN+CFR.indb 3 6/7/2019 12:45:41 PM

REMOVE PACKAGING

Remove the packaging materials. Remove the supporter frame located on the back

of the cooktop glass. Failure to remove packaging materials could result in damage

to the appliance.

PREPARE TOOLS & PARTS

The tools you will need

Drill Adjustable Wrench Pliers 1/4" Nut Driver

Phillips Screwdriver Flat Screwdriver Pencil Level

What’s included with your range

Anti-tip Bracket

Template

Anti-Tip Bracket Screws (short:2 ea,

long:2 ea)

Filler Kit

Additional materials you may need

4-Wire Cord or 3-Wire Cord

(UL Approved 40 or 50 AMP)

Strain Relief

(For Conduit Installation Only)

English - 4

Install_NE58H9970WS_AA_AC_DG68-00594B-00_EN+CFR.indb 4 6/7/2019 12:45:41 PM

CHECKING THE INSTALLATION SITE

Clearances and dimensions

To install the range, refer to the following ﬁgure.

CAUTION

CAUTIONThis range has been designed to comply with the maximum

allowable wood cabinet temperatures of 194 °F. Make sure the wall covering,

countertops, and cabinets around the range can withstand the heat (up to 194 °F)

generated by the range. If not, discoloration, delamination, or melting may occur.

SLIDE-IN CUTOUT FREESTANDING CUTOUT

36"~36-3/4"

31"

4-1/2"

23-3/16"

6-5/16"

24-11/16"

48"

28-5/8"

26-5/16"

29-15/16"

26-5/16"

Hatched Faces should

be ﬂat and leveled.

35-7/8"

23-3/16"

1/2" min.

25"

3" 24"

1" min.

25"

24" 3"

A : Cabinet opening min 30" (76.2 cm)

B : Acceptable electrical outlet area

If your cabinets are over 36-3/4" high, you must install this range on a hard, heat

resistant support that raises the surface of the range so that it is about even with

the countertop.

CAUTION

CAUTIONYou must use the rear ﬁller kit to install the range in a

freestanding cutout cabinet. For more information, see “Optional rear ﬁller kit” as shown

below.

Optional rear ﬁller kit

Used to ﬁll gap between the range back and wall. Adds a ﬁller strip to the rear of the

range. This kit can only be used when the opening in the countertop is 25” deep.

If the countertop depth is

greater than 25", there will

be a gap between the ﬁller kit

and the back wall.

English - 5

01 PREPARING TO INSTALL THE RANGE

Install_NE58H9970WS_AA_AC_DG68-00594B-00_EN+CFR.indb 5 6/7/2019 12:45:41 PM

Minimum dimensions

IMPORTANTTo eliminate the risk of burns or ﬁre caused by reaching

over heated surface units, avoid having cabinet storage space located above the surface

units. If you have cabinet storage space over the heating elements, you can reduce the

risk by installing a range hood that projects horizontally a minimum of 5 inches beyond

the bottom of the cabinets.

* 30"

30"

** 15"

* A minimum of 30" is required

between the top of the

cooking surface and the

bottom of an unprotected

wood or metal cabinet; a

minimum of 24" is required

if the bottom of the wood or

metal cabinet is protected

by not less than 1/4" of ﬂame

retardant millboard covered

with not less than no.28

MSG of sheet steel, 0.015"

of stainless steel, 0.024"

of aluminum, or 0.020" of

copper.

** A minimum of 15" is required

between the countertop and

the adjacent cabinet bottom.

English - 6

Install_NE58H9970WS_AA_AC_DG68-00594B-00_EN+CFR.indb 6 6/7/2019 12:45:41 PM

TO AVOID BREAKAGE

CAUTION

CAUTIONDo NOT lift or handle the unit by the cooktop glass.

Fig. 1

1. The counter top around the cut-out should be ﬂat and leveled (see hatched area on

Fig. 1).

2. Before installing the unit, measure the heights of the two cabinet sides (C1~C4),

front and back (See Fig. 1) from the ﬂoor to the top of the counter.

3. Level the range using the four leveling legs so that the height from the ﬂoor

to the underside of the cooktop glass frame is greater than the tallest cabinet

measurement by at least 1/16".

4. Remove the Support Frames on the back left and back right of the glass cooktop

(Refer to page 4).

5. Slide the unit into the cabinet (DO NOT PUSH THE UNIT HARD). Make sure the

center of the unit aligns with the center of the cabinet cut-out.

6. The cooktop glass frame under the cooktop glass MUST sit above the cabinet

countertop so the unit is supported by its leveling legs. The cooktop glass should

NOT directly touch the countertop If the cooktop glass is touching the countertop,

it could break, voiding the warranty.

IMPORTANTMAKE SURE the unit is supported by the leveling legs

and NOT by the cooktop itself. The cooktop glass must sit above the surface of the

countertops.

English - 7

01 PREPARING TO INSTALL THE RANGE

Install_NE58H9970WS_AA_AC_DG68-00594B-00_EN+CFR.indb 7 6/7/2019 12:45:42 PM

connecting the power

STEP 1. MEETING ELECTRICAL CONNECTION

REQUIREMENTS

CAUTION

CAUTIONFor personal safety, do not use an extension cord

with this appliance. Remove the house fuse or open the circuit breaker before

beginning installation.

This appliance must be supplied with the proper voltage

and frequency, and be connected to an individual, properly

grounded branch circuit, protected by a circuit breaker or fuse

having amperage as speciﬁed on the rating plate. The rating

plate is located above the drawer on the oven frame. (Fig. 1 or

Fig. 2)

We recommend you have the electrical wiring and hookup

of your range connected by a qualiﬁed electrician. After

installation, have the electrician show you where your main

range disconnect is located.

Check with your local utilities for electrical codes which apply

in your area. Failure to wire your oven according

to governing codes could result in a hazardous

condition. If there are no local codes, your range must

be wired and fused to meet the requirements of the

National Electrical Code, ANSI/NFPA No.

70–Latest

Edition. You can get a copy by writing:

National Fire Protection Association

Batterymarch Park

Quincy, MA 02269

Eective January 1, 1996, the National Electrical Code requires that new

construction (not existing) utilize a 4-conductor connection to an electric

range.

When installing an electric range in new construction, follow Steps 2 and 3

for a 4-wire connection.

You must use a 3-wire or 4-wire, single-phase A.C. 208Y/120 Volt or 240/120 Volt,

60 hertz electrical system.

If the electrical service provided does not meet the above speciﬁcations, have a

licensed electrician install an approved outlet.

Use only a 3-conductor or a 4-conductor UL-listed range cord. These cords may be

provided with ring terminals on the wire and a strain relief device.

(Fig. 1)

(Fig. 2)

English - 8

Install_NE58H9970WS_AA_AC_DG68-00594B-00_EN+CFR.indb 8 6/7/2019 12:45:42 PM

A range cord rated at 40 amps with 125/250 minimum volt range is required. A 50

amp range cord is not recommended but if used, it should be marked for use with

nominal 13⁄8" diameter connection openings. Care should be taken to center the

cable and strain relief within the knockout hole to keep the edge from damaging the

cable.

• Because range terminals are not accessible after the range is in position, a ﬂexible

service conduit or cord must be used.

NOTE If the power connection is plugged in improperly, the following

message appears on the display.

• LCD, PMOLED : Wire installation fail

• LED : bAd LinE

Reconnect the power connection properly, and the message disappears.

ALL NEW BRANCH-CIRCUIT CONSTRUCTIONS, MOBILE HOMES,

RECREATIONAL VEHICLES, AND INSTALLATIONS WHERE LOCAL

CODES DO NOT ALLOW GROUNDING THROUGH NEUTRAL,

REQUIRE A 4-CONDUCTOR UL-LISTED RANGE CORD.

STEP 2. ACCESSING THE POWER CORD CONNECTION

Loosen and then remove the rear access cover screw with a screwdriver. Remove

the rear access cover by pull right and then out. The terminal block will then be

accessible.

Access cover

Terminal block

English - 9

02 CONNECTING THE POWER

Install_NE58H9970WS_AA_AC_DG68-00594B-00_EN+CFR.indb 9 6/7/2019 12:45:42 PM

Speciﬁed rating of power-supply-cord kit and circuit

protection

Range rating, watts Speciﬁed rating

of power-supply-

cord kit and circuit

protection, Amps

Diameter (inches) of range

connection opening

120/240 volts

3-wire

120/208 volts

3-wire Power cord Conduit

8750 - 16500 7801 - 12500 40 or 50 A 13/8" 11/8"

This appliance must be supplied with the proper voltage at the proper frequency

and must be connected to a dedicated, properly grounded branch circuit protected

by a 40 amp or larger circuit breaker.

NOTE For power cord installations, go to page 10. For conduit installations,

go to page 13.

STEP 3. INSTALLING THE POWER CORD

For power cord installations, hook the strain relief over the power cord hole (13/8")

located below the rear of the drawer body. Insert the power cord through the strain

relief and tighten the device.

Strain relief

Power cord

Conduit connection plate

• You must install the power cord with a strain relief.

• Attach the strain relief to the 13/8" opening in the conduit connection plate.

English - 10

Install_NE58H9970WS_AA_AC_DG68-00594B-00_EN+CFR.indb 10 6/7/2019 12:45:43 PM

Tabla de contenidos

Idiomas:

Otros manuales de Rango de Samsung

Samsung

Samsung NE59J342 Manual de usuario

Samsung

Samsung NE595R0ABBB/AA Manual de usuario

Samsung

Samsung NX60CB831512AA Manual de usuario

Samsung

Samsung NSI6D 95 Series Manual de usuario

Samsung

Samsung NE63 671 S Series Manual de usuario

Samsung

Samsung NE59J7850WS Manual de usuario

Samsung

Samsung NX58K7850S SERIES Manual de usuario

Samsung

Samsung NX58F5700WS Manual de usuario

Samsung

Samsung NX58K9850S series Manual de usuario

Samsung

Samsung FCQ321HTUB Manual de usuario

Samsung

Samsung NE59J7750 series Manual de usuario

Samsung

Samsung NSI6D 91 Series Manual de usuario

Samsung

Samsung NX58K9500W Series Manual de usuario

Samsung

Samsung NX58F5500SS Manual de usuario

Samsung

Samsung NE59R6631SG/AC Manual de usuario

Samsung

Samsung NX60BG8315SSAA Manual de usuario

Samsung

Samsung NX58K7850S SERIES Manual de usuario

Samsung

Samsung NE595N0PBSR/AA Manual de usuario

Samsung

Samsung NX58M6850SS Manual de usuario

Samsung

Samsung NX58F5700WS Manual de usuario

Samsung

Samsung FX510BGS/XAA Manual de usuario

Samsung

Samsung FX710BGS Manual de usuario

Samsung

Samsung NE59M7630 Series Manual de usuario

Samsung

Samsung NX58 751 Series Manual de usuario

Manuales populares de Rango de otras marcas

Kenmore

Kenmore 790.45712 Manual de usuario

Wolf

Wolf CHR CHSSR Manual de usuario

Smeg

Smeg Built-in Microwave Oven Manual de instrucciones

Zanussi

Zanussi ZCG054G Manual de usuario

Whirlpool

Whirlpool 8575985-W Manual de lista de piezas

Frigidaire

Frigidaire 316000635 Manual de usuario

GE JCSS630 Manual de usuario

Hotpoint

Hotpoint RB524R Guía de instalación

Whirlpool

Whirlpool Roper FGP305KW3 Manual de usuario

Amana

Amana ART6610 SERIES Manual de usuario

Maytag

Maytag MERH770WB Manual de usuario

Fulgor Milano

Fulgor Milano SOFIA Manual de usuario

Premier

Premier EF-4358GH Manual de usuario

Kenmore

Kenmore 790.9010 Series Manual de usuario

KitchenAid

KitchenAid KESC300 Manual de usuario

Frigidaire

Frigidaire FFEF3012LS Guía del usuario

Diamond

Diamond G65/2F4T Manual de usuario

LG LRE3091 Manual de usuario