Samsung WSM520V Manual de usuario

WSM520V

Version 1.0 Samsung Electronics page 1 of 8

User Manual

1. Introduction

The WSM520V module is wireless audio module based on AV5100. The AV5100 is 5GHz wireless audio

SoC (System-on-chip), optimized for building point to multi-point digital wireless audio solutions such as

wireless subwoofers, wireless rear speakers and in home theater system. The AV5100 contains all the

necessary radio transceiver and digital baseband circuitry to form a complete digital wireless node without the

need for external processing.

The WSM520V can be powered from a +5V supply input and the AV5100 contains all the necessary power

management and analog circuitry needed to operate the chip.

The WSM520V can operate in upper bands (5725~5825MHz) of 5GHz spectrum, enabling worldwide

coverage.

2. Feature

Product form factor

‐Module Size (mm): 40.0 (W) X 26.0 (L) X 3.0 (H)

‐PCB size (mm): 40.0 (W) X 2.6.0 (L) x 1.0 (H)

‐Shield can (mm): 24.7 (W) X 21.9 (L) X 2.0(H)

‐Antenna Type : PCB Printed Antenna

WSM520V

Version 1.0 Samsung Electronics page 2 of 8

Complete VMX wireless audio comm. system

5.725-5.825 GHz RF operation

96dB SNR

Multiple OTA audio configuration

Low, fixed latency (<20ms)

Separate RF transmit and receive RF I/O

RX diversity

USB digital audio capability

I2S digital audio capability

Complete power management

24pin I/O connector

3. Block Diagram

The Block diagram of WSM520V module is shown in the below picture.

WSM520V block diagram

PCB Antenna 0: 5725~5825MHz

PCB Antenna 1: 5725~5825MHz

X-TAL: 16MHz

WSM520V

Version 1.0 Samsung Electronics page 3 of 8

4. Functional Diagram

The functional diagrams of WSM520V module are shown in the below pictures

The WSM520V can provide wireless audio service in applications with wireless subwoofer solution and

wireless 2.1 solutions.

WSM520V

Version 1.0 Samsung Electronics page 4 of 8

5. Operating Conditions

Symbol Parameter Min. Typ. Max. Unit

V dc Supply Voltage 4.5 5.0 5.5 V

I dc Supply current - - 500 mA

Temp Operating Temperature 5 35 ℃

6. RF Characteristics

Parameter Value Unit

Modulation Pi/4DQPSK / SSB

RF Frequency Range 5725 – 5825 MHz

Bandwidth 2 MHz

RF Frequency

Channel (0) LO : 5725, Fc: NOT USED

Channel (1) LO : 5727, Fc: NOT USED

Channel (2) LO : 5729, Fc: 5730.35

Channel (3) LO : 5731, Fc: 5732.35

Channel (4) LO : 5733, Fc: 5734.35

Channel (45) LO : 5815, Fc: 5816.35

Channel (46) LO : 5817, Fc: 5818.35

Channel (47) LO : 5819, Fc: 5820.35

Channel (48) LO : 5821, Fc: NOT USED

Channel (49) LO : 5823, Fc: NOT USED

MHz

Diversity 1TX / 2RX

Antenna peak gain 2.2 dBi

RF TX output power (tolerance) 14.0 (+2dB) dBm

7. Transmit mode

In transmit mode, the audio engine transforms the audio data into packetized digital IQ signals. These

are in turn pulse-shaped before conversion by DAC to match to the analog IQ inputs of the radio

transceiver. The radio transceiver has programmable baseband filter to lower the RF spectrum side lobes

and to suppress the DAC image and the DAC spurious. The output power is programmable. A power

detector (PD_Out) on the radio transceiver enables close-loop TX power control. The differential RF TX

DA outputs are connected via a balun filter to Power amplifier and the amplified TX carrier signal is

radiated by a printed antenna in the module after going through Transmit/Receive switch placed between

WSM520V

Version 1.0 Samsung Electronics page 5 of 8

power amplifier and the printed antenna.

8. Receive mode

In receive mode , antenna diversity is supported. The single ended output of the T/R switch is connected to

the differential RF LNA inputs in the AV5100 through balun filter. Filtering and amplification is all

performed by the radio transceiver function in the AV5100. The gain setting is controlled by BB. The

analog IQ outputs are sampled by the BB having dual channel ADC to convert. The received data is

demodulated and fed to the audio processing engine controlling the audio function

9. Clock

The main crystal is connected to the AV5100 IC. The clock frequency is 16MHz and feed it to the AV5100.

10. I/O interface

The WSM520V module has 24pin-FPC connector for I/O interface. The 24-pin connector is configured as

the following table.

Pin Number Pin Name I/O Description

1 VDD_5V PWR Regulated 4.5V to 5.5V input

2 VDD_5V PWR Regulated 4.5V to 5.5V input

3 GPIO5 / I2CS_SCL I/O I2C serial clock slave

4 GPIO4 / I2CS_SDA I/O I2C serial data slave

5 GPIO19 / WCLK1 I/O I2S Left Light clock 1

6 RESET I Reset

7 GPIO9 / MISO_EXT_FLASH I/O External flash memory data output

8 GPIO8 / MOSI_EXT_FLASH I/O External flash memory data input

9 GPIO17 / I2CM_SCL I/O I2C serial clock master

10 GPIO16 / I2CM_SDA I/O I2C serial data master

11 GPIO10 /MCLK I/O 12.288MHz Audio clock I/O

12 GND GND GND

13 GPIO11 /I2S_BCK0 I/O I2S Bit clock 0

14 GPIO12 /I2S_WCLK0 I/O I2S Left Light clock 0

15 GPIO6 / CS_EXT_FLASH I/O External flash memory chip select

16 GPIO13 /I2S_DAT_0 I/O I2S data 0

17 GPIO7 / SCLK_EXT_FLASH I/O External flash memory clock input

18 GPIO14 / I2S_DAT_1 I/O I2S data 1

19 GPIO15 / I2S_DAT_2 I/O I2S data 2

20 GPIO18 /BCK1 I/O I2S Bit clock 1

21 GPIO2 /S_SSB I/O

22 GPIO3 /S_SCLK I/O

23 GPIO24 I/O GPIO

24 GND GND GND

WSM520V

Version 1.0 Samsung Electronics page 6 of 8

11. Notice

FCC Statement

This device complies with Part 15 of FCC Rules, Operation is Subject to following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received including interference that cause undesired operation.

Caution: Any changes or modifications to the equipment not expressly approved by the party responsible for

compliance could void user s authority to operate the equipment.

This equipment has been tested and found to comply within the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a different circuit from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help.

This device and its antenna(s) must not be co-located or operation in conjuction with any other antenna or transmitter.

IMPORTANT NOTE:

FCC Radiation Exposure Statement;

This appliance and its antenna must not be co-located or operation in conjunction with any other antenna or

transmitter.

A minimum separation distance of 20

㎝

must be maintained between the antenna and the person for this appliance

to satisfy the RF exposure requirements.

USER MANUAL OF THE END PRODUCT:

In the users manual of the end of product, the end user has to be informed to keep at least 20cm separation with the

antenna while this end product is installed and operated.

WSM520V

Version 1.0 Samsung Electronics page 7 of 8

IC Statement

The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can

be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the

manufacturer could void the user’s authority to operate this equipment.

If the size of the end product is smaller than 8x10cm, then additional FCC part15.19statement is required to be available

in the users manual; This device complies with Part15 of FCC rules.

LABEL OF THE END PRODUCT:

The final end product must be labeled in a visible area with the following " Contains TX FCC ID: A3LWSM520V ". If

the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available

on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference and

(2) this device must accept any interference received, including interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

Operation is subject to the following two conditions:

(3) this device may not cause harmful interference and

(4) this device must accept any interference received, including interference that may cause undesired operation.

Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.

This device and its antenna(s) must not be co-located or operation in conjuction with any other antenna or transmitter.

The device could automatically discontinue transmission in case of absence of information to transmit, or operational

failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive

codes where required by the technology.

IMPORTANT NOTE:

IC Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 20cm between the radiator & your body

WSM520V

Version 1.0 Samsung Electronics page 8 of 8

IMPORTANT NOTE:

This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance requirement

of the end product, which integrates this module.

20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is

integrated into. Under such configuration, the IC RSS-102 radiation exposure limits set forth for an population/

uncontrolled environment can be satisfied.

Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this

equipment.

USERS MANUAL OF THE END PRODUCT:

In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the

antenna while this end product is installed and operated. The end user has to be informed that the IC radio-frequency

exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any

changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this

equipment. IC statement is required to be available in the users manual: This Class B digital apparatus complies with

Canadian ICES-003.

Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2)

this device must accept any interference received, including interference that may cause undesired operation.

LABEL OF THE END PRODUCT:

The final end product must be labeled in a visible area with the following " Contains TX IC : 649E‐WSM520V ".

Tabla de contenidos

Otros manuales de Unidad de control de Samsung

Samsung

Samsung MCU-R4NEK0N Manual de usuario

Samsung

Samsung MIM-E03A Manual de usuario

Samsung

Samsung SPC-6000 Manual de usuario

Samsung

Samsung WEC8500 Manual de usuario

Samsung

Samsung WIDA10 Manual de usuario

Samsung

Samsung MIM-E03 series Manual de usuario

Samsung

Samsung SSM-D1000 Manual de usuario

Samsung

Samsung MIM-B16 Manual de usuario

Samsung

Samsung OfficeServ 7400 GPLIMT Manual de usuario

Samsung

Samsung SPC-6000 Manual de usuario

Samsung

Samsung WCA720M Manual de usuario

Samsung

Samsung RC160MHXGA Manual de usuario

Samsung

Samsung WSNFM400A00 Manual de usuario

Samsung

Samsung GT-Y3400 Instrucciones de montaje

Samsung

Samsung AVR-M200FHAX Manual de usuario

Samsung

Samsung AVR-M100FHAX Manual de usuario

Samsung

Samsung CBAP210A Manual de usuario

Samsung

Samsung CY-LHDE01A Manual de usuario

Samsung

Samsung MCU-S6NEE1N Manual de usuario

Samsung

Samsung MIM-F10N Manual de usuario

Samsung

Samsung CCBQ730M Manual de usuario

Samsung

Samsung MIM-B12 Manual de usuario

Samsung

Samsung MCU Series Manual de usuario

Samsung

Samsung MIM-N10 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario