Salus RT300 Manual de usuario

Instruction Manual

Model No RT300

Digital Room Thermostat

RT300 100X115mm_Layout 1 23/08/2013 09:09 Page 1

PRODUCT COMPLIANCE

This product complies with the essential requirements of the following EC

Directives:

•Electro-Magnetic Compatibility directive 2004/108/EC

•Low Voltage Directive 2006/95/EEC

•EC Marking directive 93/68/EEC

SAFETY INFORMATION

These instructions are applicable to the SALUS Controls model stated on the

front cover of this manual only, and must not be used with any other make or

model.

These instructions are intended to apply in the United Kingdom only, and

should be followed along with any other statutory obligations.

This accessory must be fitted by a Competent person, and installation must

comply with the guidance provided in the current editions of BS7671 (IEE

Wiring Regulations) and Part ‘P’ of the Building Regulations. Failure to

comply with the requirements of these publications could lead to

prosecution.

Always isolate the AC Mains supply before opening or removing the

unit from the wall or wall box.

When fitting batteries don’t mix old and new batteries together. Do

not use rechargable batteries.

Please leave these instructions with the end user where they should be kept

in a safe place for future reference.

RT300 INSTRUCTION MANUAL

RT300 100X115mm_Layout 1 23/08/2013 09:09 Page 2

What is a room thermostat?

... an explanation for householders

A room thermostat simply switches the heating system on and off as necessary. It

works by sensing the air temperature, switching on the heating when the air

temperature falls below the thermostat setting, and switching it off once this set

temperature has been reached.

Turning a room thermostat to a higher setting will not make the room heat up any

faster. How quickly the room heats up depends on the design of the heating system,

for example, the size of boiler and radiators.

Neither does the setting affect how quickly the room cools down. Turning a room

thermostat to a lower setting will result in the room being controlled at a lower

temperature, and saves energy.

The heating system will not work if a time switch or programmer has switched it off.

The way to set and use your room thermostat is to find the lowest temperature setting

that you are comfortable with, and then leave it alone to do its job. The best way to

do this is to set the room thermostat to a low temperature – say 18oC – and then turn

it up by one degree each day until you are comfortable with the temperature. You

won’t have to adjust the thermostat further. Any adjustment above this setting will

waste energy and cost you more money.

If your heating system is a boiler with radiators, there will usually be only one room

thermostat to control the whole house. But you can have different temperatures in

individual rooms by installing thermostatic radiator valves (TRVs) on individual

radiators. If you don’t have TRVs, you should choose a temperature that is reasonable

for the whole house. If you do have TRVs, you can choose a slightly higher setting to

make sure that even the coldest room is comfortable, then prevent any overheating in

other rooms by adjusting the TRVs.

Room thermostats need a free flow of air to sense the temperature, so they must not

be covered by curtains or blocked by furniture. Nearby electric fires, televisions, wall

or table lamps may prevent the thermostat from working properly.

RT300 INSTRUCTION MANUAL 3

RT300 100X115mm_Layout 1 23/08/2013 09:09 Page 3

INSTALLATION

Please read the important safety information at the start of this manual before you

begin to install the thermostat.

The ideal position to locate the RT300 thermostat is about 1.5m above floor level, in

a location where the thermostat is accessible, reasonably lit and free from extremes of

temperature and draughts. Do not mount the thermostat on an outside wall, above a

radiator or in a location where it may be subjected to direct sunlight.

The electrical connections to the RT300 are made to the supplied industry standard

backplate. This simplifies installation, as no connections are made to the controller

itself. Connection details are shown below - no Earth connection is required for the

correct and safe operation of the RT300, but a parking terminal is provided to connect

an Earth wire if one is present.

RT300 INSTRUCTION MANUAL

INTRODUCTION

A thermostat is a device that is used to switch the heating system in your home on

and off as needed. It works by sensing the air temperature and switching on the

heating when the air temperature falls below the thermostat setting, and switching

it off once the set temperature has been reached.

The RT300 from SALUS Controls is a stylish and

accurate digital thermostat with a large, easy to

read Liquid Crystal Display (LCD). This thermostat

has been specifically designed to be used Volt Free.

Features

•Volt free contacts

•Frost protection

•Large, easy to read LCD with blue backlight

•Burner on symbol

•User friendly

•Stylish casing

RT300 100X115mm_Layout 1 23/08/2013 09:09 Page 4

Backplate Connections

Terminal Description Backplate

L Mains Live

SL Switched Live

(Normally Open Contact)

Earth Parking (no electrical

connection)

After installing the backplate in a suitable location, wiring connections can be made as

shown above. The following criteria apply to the installation:

• The incoming AC mains supply should be 230V AC and fused at 5 amps.

• Optimum cable size for installation is 1.5 mm2; wiring colours should be

in accordance with the current requirements of the IEE Wiring Regulations.

• Cable entry should be from the rear of the backplate.

• All wiring connections should be securely made, and be firmly

gripped beneath the square brass washer on each terminal.

The RT300 requires two ‘AA’ alkaline batteries to function correctly. Ensure that the

batteries are inserted correctly, paying careful attention to the polarity markings on the

battery and next to the battery holders.

Do not restore the mains supply to the system until all associated items are fully installed.

NOTE: All electrical installation work should be carried out by a suitably qualified Electrician

or other competent person. If you are not sure how to install this thermostat consult either

with a qualified electrician, heating engineer or your boiler / heating system supplier for

advice on how to continue.

Do not remove or refit the RT300 onto the backplate without

the mains supply to the system being isolated.

RT300 INSTRUCTION MANUAL 5

RT300 100X115mm_Layout 1 23/08/2013 09:09 Page 5

JUMPER SETTINGS

Changes to the jumper settings should only be made by the Engineer carrying out the

installation or other qualified person.

The installer should select the jumper positions required if changes need to be made

to the factory default settings. These jumpers are found on the rear of the Control

Centre.

Jumper Function Default

Temperature Movable jumper for ± 0.5 ºC span

Span ± 0.5 ºC or ± 1.0 ºC span.

RT300 INSTRUCTION MANUAL

RT300 100X115mm_Layout 1 23/08/2013 09:09 Page 6

AFTER INSTALLATION

After completing installation and powering up the RT300 for the first time the

thermostat will behave in the following way:

All the indicators on the display and the backlight will be turned

on for two seconds. After two seconds, the RT300 will then

operate in Normal mode (Normal mode is when the thermostat

is displaying the room temperature).

The following table shows the settings of the RT300 digital thermostat

after Power on:

Function Status After Reset or Power On

Operation Mode Normal mode

Room Temperature 22.0 °C, updated within 5 seconds

Set Point Temperature 20.0 °C

°C indicator On

Frost Protection indicator Off

Heat indicator Off

Low-Battery Warning indicator Off, updated within 5 seconds

Output Relay Off

After Power on, the thermostat will operate in Normal mode (Normal mode is when

the thermostat is displaying the room temperature):

•The set point temperature is reset to the default setting

•The room temperature display is updated within 5 seconds

•The control process starts

RT300 INSTRUCTION MANUAL 7

RT300 100X115mm_Layout 1 23/08/2013 09:09 Page 7

OPERATION

The status and operation of the RT300 is clearly

shown on the large backlit Liquid Crystal Display

(LCD). This display allows the user a clear

indication of the current room temperature, and

the status of the heating system.

There are few user controls for the RT300, making

this thermostat very easy to operate. These

controls are shown below, along with a description

of each of their functions.

USER CONTROL FUNCTION SUMMARY

Key / Operation Symbol Functions

UP key Increases the selected setting

DOWN key Decreases the selected setting

BACKLIGHT / Manually turns on the LCD backlight

FROST key for 5 seconds, or activates /

deactivates Frost Protection

RT300 INSTRUCTION MANUAL

RT300 100X115mm_Layout 1 23/08/2013 09:09 Page 8

REVIEWING SET POINT TEMPERATURE

You can view the set point temperature at any time by

pressing either the UP or DOWN key.

To exit from the set point review, press the BACKLIGHT /

FROST key, or don’t press any keys for approximately four

seconds – either of these actions will return the RT300 to

displaying current room temperature.

SETTING SET POINT TEMPERATURE

You can change the set point temperature very easily while

you are reviewing the set point temperature. Press the UP or

DOWN keys repeatedly to change the temperature setting.

The set point temperature will flash to indicate that it can be

changed:

The temperature will be changed in 0.5°C steps per key press. The RT300 will return

to Normal mode if no keys are pressed for more than four seconds.

Set point temperature cannot be changed if Frost Protection mode is enabled.

RT300 INSTRUCTION MANUAL 9

RT300 100X115mm_Layout 1 23/08/2013 09:09 Page 9

FROST PROTECTION

To enable the Frost Protection mode, press and hold the BACKLIGHT / FROST button

for three seconds. Once Frost Protection is enabled, the set point temperature is

automatically set to 5°C to provide protection from the risk of freezing.

Whenever Frost Protection is activated, the Frost Protection indicator will flash in the

sequence shown below:

To turn off Frost Protection mode, press and hold the BACKLIGHT / FROST button for

three seconds.

Please be aware that the Frost Protection mode operates as an additional protection

feature but should not be used in place of a correctly installed frost thermostat, which

is required to override all other controls in the system.

The backlight will remain illuminated for approximately 5 seconds.

RT300 INSTRUCTION MANUAL

RT300 100X115mm_Layout 1 23/08/2013 09:09 Page 10

Otros manuales para RT300

Tabla de contenidos

Otros manuales de Termostato de Salus

Salus

Salus RT 10 Manual de usuario

Salus

Salus RT510BC+ Manual de usuario

Salus

Salus Quantum SQ610 Manual de usuario

Salus

Salus RT510BC+ Manual de usuario

Salus

Salus ST620 Manual del propietario

Salus

Salus VS30W Manual de usuario

Salus

Salus VS20WRF Manual de usuario

Salus

Salus DIGITAL PROGRAMMABLE THERMOSTAT Manual de usuario

Salus

Salus BTRP230(50) Manual de usuario

Salus

Salus RT310TX Manual de usuario

Salus

Salus RT510BC+ Manual de usuario

Salus

Salus 091FLRF Manual de usuario

Salus

Salus TS600 Manual de usuario

Salus

Salus HTRP-RF(50) Manual de usuario

Salus

Salus SOLO ST920WF Manual de usuario

Salus

Salus RT510RF Manual de usuario

Salus

Salus Thermo 091 Manual de usuario

Salus

Salus RT520RF Manual de usuario

Salus

Salus RT310RF Manual de usuario

Salus

Salus BTRP230V Manual de usuario

Salus

Salus BTRP230 Manual de usuario

Salus

Salus CT100 Manual de usuario

Salus

Salus ST620VBC Manual de usuario

Salus

Salus ST320 Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario