Safe Fleet RVS-218627 Manual de usuario

Reverse With Condence ™ 1

G-SERIES Backup Camera System

with Navigation and Bluetooth

RVS-218627

Instruction Manual

RVS Systems

Introduction...............................03

SafetyInformation..........................04-06

Before Beginning Installation. . . . . . . . . . . . . . . . . . . . . . . 07

InstallationGuide.......................... 08-09

AdjustableGridLine...................... ...10

InstallationandWire.........................11-13

GPS Navigation Menu and Function. . . . . . . . . . . . . . . . . . . . 1420

Bluetooth Setting and Instruction. . . . . . . . . . . . . . . . . . 2131

MonitorSpecications..........................32

CameraSpecication. .........................33

CameraInstallation...........................34

Troubleshooting.............................35

Warranty&Disclaimer........................ 36-37

TABLE OF CONTENTS

Reverse With Condence ™ 3

NOTE! Please read all of the installation instructions

carefully before installing the product. Improper

installation will void manufacturer’s warranty.

Congratulations on purchasing a RearView Backup

Camera System!

With this manual you will be able to properly install and

operate the unit.

The Backup Camera System is intended to be installed as a

supplement aid to your standard rear view mirror that already exists

in your vehicle. The Backup Camera System should not be used as a

substitute for the standard rear view mirror or for any other mirror

that exists in your vehicle.

In some jurisdictions, it is unlawful for a person to drive a

motor vehicle equipped with aTV viewer or screen located forward of

the back of the driver’s seat or in any location that is visible, directly

or indirectly, to the driver while operating the vehicle.

INTRODUCTION

RVS Systems

Please read the entire manual and follow the instructions and

warnings carefully. Failure to do so can cause serious damage and/or

injury, including loss of life. Be sure to obey all applicable local

trac and motor vehicle regulations as it pertains to this product.

Improper installation will void manufacturer’s warranty.

• The Rear View Camera System is

designed to help the driver safe-

ly detect people and/or objects

helping to avoid damage or injury.

However, you the driver, must use it

properly. Use of this system is not a

substitute for safe, proper or legal

driving.

• Never back up while looking at the

monitor alone. You should always

check behind and around the vehi-

cle when backing up, in the same

way as you would if the vehicle did

not have the Rear View Camera

System.Ifyoubackupwhilelooking

only at the monitor, you may cause

damage or injury. Always back up

slowly.

•The Rear View Camera System is

not intended for use during exten-

sive back-up maneuvers or backing

into cross trac or pedestrian walk-

ways.

•Please, always remember, the area

displayed by the Rear View Camera

Systemis limited.It doesnotdisplay

the entire panorama that is behind

you.

USAGE:

SAFETY INFORMATION

Reverse With Condence ™ 5

•Electric shock or product

malfunction may occur if this

product is installed

incorrectly.

• Use this product within

the voltage range specied. Failure

to do so can cause

electronic shock or product

malfunction.

• Take special care when

cleaning the monitor.

•Make sure to rmly ax the prod-

uct before use.

• If smoke or a burning smell

is detected, disconnect the

system immediately.

•Where the power cable may touch

a metal case, cover the cable with

friction tape. A short circuit

or disconnected wire may cause a

re.

• While installing the Rear View

System be careful with the wire

positioning in order to avoid wire

damage.

• The Rear View System should only

be used when the vehicle is in

reverse.

• Do not watch movies or

operate the monitor while driving;

as it may cause an

accident.

• Do not install the monitor

where it may obstruct drivers

view or obstruct an air bag

device.

• Dropping the unit may cause

possible mechanical failure.

INSTALLATION:

SAFETY INFORMATION

RVS Systems

If you have questions about this product, contact:

RVS Systems

1797 Atlantic Avenue

Brooklyn, NY 11233

Tel: 1.800.764.1028

IN NO EVENT SHALL SELLER OR MANUFACTURER BE

LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF

ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM

ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.

SAFETY INFORMATION

Reverse With Condence ™ 7

Before drilling please check that no cable or wiring is on the other side

of the wall. Please clamp all wires securely to reduce the possibility

of them being damaged while vehicle is in use. Keep all cables away

from hot or moving parts and electrical noisy components.

We recommend doing a benchmark test before installation

to insure that all components are working properly.

Step 1: Choose the monitor and camera locations.

Step 2: Install all cables in vehicle, when necessary a 0.8 (20mm)

hole should be drilled for passing camera cable through vehicles

walls. Install split grommets where applicable.

Step 3: Once all cables and wiring have been properly routed, perform

a system function test by temporarily connecting the system. If the

system seems to not be operating properly see troubleshooting (page

35).

BEFORE YOU BEGIN

RVS Systems

Replacement Monitor

The mirror monitor replaces the existing car mirror. Carefully remove

the mirror o the“pin”. Slide the replacement mirror on to the pin and

secure it with the screw provided (already in the screw hole).Dier-

ent cars have dierent brackets. Depending on your vehicle make and

manufacturer. There are many methods to remove the original rear-

view mirror, however, please don’t force the mirror o the bracket.

The manufacturer will not be responsible for damage caused to your

car by wrong installation of the mirror. Figure 1.1

Clip-On Monitor

1. The Mirror Monitor attaches to the existing rear view mirror in

vehicle with the pressurized clips on the back of the monitor.

2. Attach monitor to existing mirror, and adjust mounting angle to

allow optimum driver viewing comfort.

Camera & Cable

Be sure to position the cable properly. The aviation camera cable uses

aircraft grade connectors which means the camera cable can be ex-

posed to all weather elements. Do not run the cable over sharp edges,

do not kink the cable and keep away from HOT and rotating parts.

Fasten all cables and secure all excess cable. Connect camera to the

camera extension cable which runs inside the vehicle. Figure 1.2

INSTALLATION GUIDE

Reverse With Condence ™ 9

Wiring

After connecting the camera to the“camera cable”the camera should

be plugged into AV2 input. Connect the RED 12V power wire to a an

ignition power source and the BLACK 12V ground wire to a chassis

ground.The GREEN wire is the REVERSE trigger wire. Connect this wire

to the vehicle’s backup light circuit to activate the rear-view image

whenever the vehicle shifts into reverse. To connect a second camera,

connect it to AV1 input. It can be turned on by pressing the power but-

ton on the monitor. Figure 2.1, Figure 2.2

Precautions for use of Mirror Monitor

I. The Mirror Monitor is made of glass. Do not subject it to a

mechanical shock by dropping it from a high place, etc.

II. Do not apply excessive force to the monitor surface or the

adjoining areas since this may cause the color tone to vary.

III. Clean with a soft dry cloth and/or Windex only.

IV. Do not attempt to disassemble the mirror monitor.

Safety

• Before drilling, be sure no cable or wire is on the other side.

• Feed as much cable as possible into vehicle & clamp securely.

This reduces the possibility of cable being hooked or snagged.

INSTALLATION GUIDE + TIPS

RVS Systems

Generally, to help drivers estimate the distance from obstacles, there are

three lines for reference- red, yellow, and green. Those three lines are dis-

played on the monitor when car is reversing. The green line is 3M from the

back of the car and the yellow line is 6.5 ft. The distant red line is 1M from

the backside of car while the close red line is 0.4M. Both reference lines on

the left and right should leave 0.2M space from the car.

The accuracy of the grid-lines can vary based on how you angle your cam-

era. Therefore to compensate for inaccurancies, you can adjust the grid-

lines to your camera angle.

ADJUSTABLE GRID LINE

Accuracy

Grid Lines

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Electrónica del automóvil de Safe Fleet

Safe Fleet

Safe Fleet RVS-218628 Manual de usuario

Safe Fleet

Safe Fleet REAR VIEW SAFETY RVS-111 Manual de usuario

Safe Fleet

Safe Fleet RVS-507620 Manual de usuario

Safe Fleet

Safe Fleet Rear view safety RVS-255W Manual de usuario

Safe Fleet

Safe Fleet RVS-218629 Manual de usuario

Safe Fleet

Safe Fleet RVS-082550 Manual de usuario

Safe Fleet

Safe Fleet RVS-218623 Manual de usuario

Safe Fleet

Safe Fleet RVS-218633 Manual de usuario

Safe Fleet

Safe Fleet RVS-082575 Manual de usuario

Safe Fleet

Safe Fleet RVS-218622 Manual de usuario

Manuales populares de Electrónica del automóvil de otras marcas

GoldCruise

GoldCruise GC90Ci Manual de usuario

DRG

DRG LC 120 Manual de usuario

Blue Ox

Blue Ox BX8848 Manual de usuario

Dometic

Dometic MAGICWATCH MWE890K Manual de usuario

Perfect Power

Perfect Power SMT8-T5 Manual de usuario

Honeywell

Honeywell Thor VM3A Manual de usuario

Waeco

Waeco MagicWatch MWE250 Manual de usuario

Rydeen

Rydeen BKM091 Manual de usuario

Skoda

Skoda 5E0 054 630 Manual de usuario

VDO

VDO SENDER UNIT 2159-0 Manual de usuario

iDataLink

iDataLink maestro Rr Manual de usuario

Audiovox

Audiovox PRO-PDA15 Manual de usuario

Movon

Movon MDAS-3LFFHD Manual de usuario

Pioneer

Pioneer Comfort adapter CA-D-PI.150 Manual de usuario

Dietz

Dietz 1110 Manual de usuario

Crux

Crux RVCFD-79 Manual de usuario

Nonda

Nonda ZUS Manual de usuario

iDataLink

iDataLink Maestro Manual de usuario