RVS SenseVue Manual de usuario
SenseVueTM Customizable
Surround Sensor System w/
LED Display
Instruction Manual
©Rear View Safety 2023
RVS-SenseVue
(Up to 16 Sensors)
2
Rear View Safety, 1797 Atlantic Ave., Brooklyn NY 11233
www.rearviewsafety.com
Table of contents .........................................................................................2
Introduction ...................................................................................................3
Safety Information ...................................................................................4-5
Required Tools ..............................................................................................6
System Content ............................................................................................6
Wire Diagram ................................................................................................7
Display Function ..........................................................................................8
Sensor Location Requirements .................................................................9
Sensor Location Examples ......................................................................10
Sensor and Sleeve Mounting ..................................................................11
Door Installation Instructions ................................................................12
Harness Routing ..........................................................................................13
ECU Installation ..........................................................................................14
GPS and Display Locations ....................................................................15
Functionality Check ...................................................................................16
Technical Specification ...........................................................................17
Warranty ......................................................................................................18
Disclaimer ....................................................................................................19
TABLE OF CONTENTS
Rear View Safety, 1797 Atlantic Ave., Brooklyn NY 11233
www.rearviewsafety.com 3
With this product, you are taking an active part in reducing dangerous road
trac events while keeping yourself, passengers, and pedestrians safe. This
manual will take you step by step through the installation process and usage of
SenseVue™.
Please read all of the installation instructions
carefully before installing the product. Improper
installation will void manufacturer’s warranty.
INTRODUCTION
4
Rear View Safety, 1797 Atlantic Ave., Brooklyn NY 11233
www.rearviewsafety.com
SAFETY INFORMATION
USAGE : The Sensor System is designed to help the driver improve their attention
on the road and avoid accidents stemming from distractions. However, you the
driver, must use it properly. Use of this system is not a substitute for safe, proper
or legal driving.
PLEASE READ THE ENTIRE MANUAL AND FOLLOW THE INSTRUCTIONS
AND WARNINGS CAREFULLY. FAILURE TO DO SO CAN CAUSE SERIOUS
DAMAGE AND/OR INJURY, INCLUDING LOSS OF LIFE. BE SURE TO OBEY ALL
APPLICABLE LOCAL TRAFFIC AND MOTOR VEHICLE REGULATIONS AS IT
PERTAINS TO THIS PRODUCT. IMPROPER INSTALLATION WILL VOID
MANUFACTURER’S WARRANTY.
INSTALLATION
Electric shock or product malfunction may occur if this product
is installed incorrectly.
• Use this product within the voltage range specified; failure to do so can
cause electronic shock or product malfunction
• Take special care when cleaning the monitor
• Make sure to firmly ax the product before use
• If smoke or a burning smell is detected, disconnect the system immediately
• Where the power cable may touch a metal case, cover the cable with
friction tape; a short circuit or disconnected wire may cause a fire
• While installing the RVS System, be careful with the wire positioning in
order to avoid wire damage
• Do not watch movies or operate the monitor while driving, as it may cause
an accident
Rear View Safety, 1797 Atlantic Ave., Brooklyn NY 11233
www.rearviewsafety.com 5
Reading the instruction of this manual before using SenseVue™ is mandatory:
1. The use of the system does not constitute a permit for the driver to drive the
vehicle illegally or an authorization to breach road trac laws. Any violation of
trac laws is the sole responsibility of the driver. RVS will not compensate the
drivers for any damage caused to the driver and/or passengers of the vehicle
and/or vehicle and shall have no responsibility arising from the behaviors
mentioned above.
2. The SenseVue™ system only alerts (in accordance with system restrictions)
the drivers against hazards depending on the features installed in the system.
The final decision on how to operate/control the vehicle will be made by the
drivers and their responsibility.
• Do not install the monitor where it may obstruct the driver's view or obstruct
an airbag device
• Dropping the unit may cause possible mechanical failure
• When in reverse, monitor buttons are not functional
BEFORE USING SenseVue™, CAREFULLY READ THE FOLLOWING SAFETY
INSTRUCTIONS AND WARNINGS THIS GUIDE CONTAINS
6
Rear View Safety, 1797 Atlantic Ave., Brooklyn NY 11233
www.rearviewsafety.com
REQUIRED TOOLS
SYSTEM CONTENT
1. 25mm hole saw
2. Trim Removal tools
3. Wire cutters
4. Power Drill (driver bits and sockets
needed)
5. Electrical Tape
6. Solder
7. Painters tape and a marker
Rear View Safety, 1797 Atlantic Ave., Brooklyn NY 11233
www.rearviewsafety.com 7
WIRE DIAGRAM
SENSOR PLACEMENT AND DETECTION RANGE
S1
S9
S10
S 11
S13
S14
S15
S12 S16
S4
S3S2
S5 S8
S7S6
S1
S9
S10
S 11
S12
S13
S14
S4
S3S2
S5 S8
S7S6
2’
5’
8’
8’
5’
2’
1’
2’
4’
S1
S9
S10
S 11
S12
S13
S14
S4
S3S2
S5 S8
S7S6
14 Sensors Placement 16 Sensors Placement Detection Range
12 sensors - 3 on each side
14 sensors - 4 on each side
16 sensors - 6 on each side
*other customization options available
8
Rear View Safety, 1797 Atlantic Ave., Brooklyn NY 11233
www.rearviewsafety.com
DISPLAY FUNCTION
Rear View Safety, 1797 Atlantic Ave., Brooklyn NY 11233
www.rearviewsafety.com 9
SENSOR LOCATION REQUIREMENTS
Sensor installation height and the space between each sensor is important and will vary
from vehicle type to vehicle type. Follow the basic requirements below and refer to the
vehicle type suggestions that follow.
For all sensor mounting locations, the mounting surface should be perpendicular to the
ground, and should not point the sensor in a downward direction. Each location should
also be parallel to the side of the vehicle and allow the sensor to point directly out from
the side it is installed on. Make sure there is over an inch of open space behind the
surface for the sensor to fit.
Installation Height: 20”-34” will provide the best results
Installing above or below this range can result in false alerts or missed obstacles. For side
sensors, it may be dicult to find good locations that are all the exact same height from
the ground. Small changes in height are acceptable, but should not vary more than 1ft.
Front/Rear Sensor Spacing: 1ft-2ft will provide best results
Greater spacing can be used if needed, but should be avoided if possible.
Left/Right Sensor Spacing: Should not exceed 4.5ft (14 Sensor System Variant)
Based on acceptable location of the rear most sensors, S11/S14, and the forward most
sensors, S9/S12, try to equally space S10/13 between them. The total distance between
outer sensors should not exceed 9 feet and the middle sensor should be as centered as
possible. (See harness routing diagram for reference).
After measuring and checking the front and back of each sensor location, mark the
sensor locations using tape and a marker.
10
Rear View Safety, 1797 Atlantic Ave., Brooklyn NY 11233
www.rearviewsafety.com
SENSOR LOCATION EXAMPLES
Here are some basic vehicle types that the system can be installed on. Each blue “X”
represents a sensor. Use these examples as a baseline when evaluating areas on a
vehicle for side sensor placement. These general areas should provide the best side
coverage and require the fewest door installations.
At each of the marked locations, you can begin drilling the mounting hole for the sensor
using a 25mm hole saw (15/16th’s can be used as a substitute).
Use of cutting oil periodically as you drill each hole is highly recommended, especially on
heavy duty bumpers. This will give cleaner edges, faster drilling time, and extend the life
of the bit.
Once all of the holes have been cut and cleared of any burrs, you can begin installation of
sensors into their mounting holes.
HOLE SAW AND DRILLING
Tabla de contenidos
Otros manuales de Accesorios para automóviles de RVS
