Russell Hobbs EASY Manual de usuario

£10,000 prize draw

EXTRA year guarantee

FREE rewards gallery

www.productregister.co.uk/rhobbs

See back for

details

instructions

Read the instructions, keep them safe, pass them on if you pass the iron on.

AIMPORTANT SAFEGUARDS

Follow basic safety precautions, including:

1 This appliance can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have

been supervised/instructed and understand the hazards

involved. Children shall not play with the appliance. Cleaning and

user maintenance shall not be done by children unless they are

older than 8 and supervised. Keep the iron and cable out of reach

of children under 8 years.

2 Set the base unit on a stable, level, heat-resistant surface,

preferably a purpose-built “steam generator” type ironing board.

3 Rest the iron only on the base unit.

4 Use the iron only on a stable surface.

5 Don’t leave the iron unattended while plugged in or standing on

the ironing board. It could be knocked over.

6 Unplug the iron before ﬁlling, before cleaning, and after use.

7 Don’t use the iron if it’s dropped, damaged, malfunctions or leaks.

8 If the cable is damaged, return the iron, to avoid hazard.

hThe surfaces of the appliance will get hot.

UDon’t unscrew the boiler access knob till the appliance has cooled down completely

(at least 2 hours).

LDon’t put the iron in liquid.

9 Don’t iron clothing while it’s being worn – you’ll burn or scald the wearer.

10 Don’t touch the soleplate, and keep away from the steam coming from it.

11 Don’t set the base unit on a soft, carpeted, or upholstered surface, as this may block

the vents underneath the base unit.

12 Don’t use the iron for any purpose other than those described in these instructions.

13 Take care not to scratch the soleplate – avoid buttons, zips, etc.

14 The iron has a protective thermal fuse, which will blow if it overheats. If this

happens, the iron will stop working, and must be returned for repair.

household use only

CREMOVE ALL PACKAGING

•Remove any labels, stickers or packaging from the iron and soleplate.

CCURE THE ELEMENT

•Before using the iron for the ﬁrst time, or if it’s not been used for a long time, iron a

scrap piece of cotton (an old towel is ideal) to remove any accumulated residues.

•Don’t worry if the iron smokes a bit at ﬁrst, it’ll stop as the residues evaporate.

CUSING THE CLAMPS

1 Before switching on, press Uon one clamp, to unlock the iron from the base unit.

2 If you forget, the expansion of the heating soleplate may lock the clamps into place.

3 If this happens, unplug, wait till the appliance cools, then try again.

4 After use, set the iron on the base unit, press Lon one clamp, to move the tops of

both clamps inwards, and lock the iron to the base unit.

5 You may now carry the whole appliance by gripping the handle of the iron with one

hand, and putting the other hand underneath the base unit for support.

CWATER

6 Use ordinary tap-water – the anti-scale cartridge will soften the water.

7 If the anti-scale cartridge needs replacing, and you don’t have a replacement, you

should use distilled water while you’re waiting for the replacement to be delivered.

8 If you buy distilled water, check that it’s marketed as suitable for irons.

9 Don’t add anything to the water, and don’t use water with anything added to it.

10 When the water is converted to steam, chemicals, perfume, and other additives will

coat the inside of the steam chamber, shortening the life of the iron.

CFILLING

11 Switch oﬀ (2), and unplug before ﬁlling.

the easy way

12 With the reservoir in place, and one eye on the xmark, pour water slowly into the

funnel in the rear of the base unit.

13 The bottom of the funnel feeds directly into the reservoir.

14 Prime the iron before use – see below.

the other way

15 Reach under the end of the reservoir, raise the reservoir release, and slide the

reservoir out of the base unit.

16 Pour water into the hole in the top of the reservoir, up to, but not over x.

17 Slide the reservoir into the base unit.

18 Check that the catch on the reservoir clicks into place in the base unit.

19 Prime the iron before use – see below.

CSWITCH ON

20 Set the iron on top of the base unit.

21 Check that the clamps are in the release position (press U).

22 Lift the iron oﬀ the base unit, unwind the steam pipe from its niche above the

reservoir and cable storage, then set the iron back on the base unit.

23 Open the cable storage ((), pull out the plug and all the cable, thread the cable

through the adjacent gap, and close the cable storage.

24 Put the plug into the power socket (switch the socket on, if it’s switchable).

•The 2button will blink red.

25 Press the 2button to switch the appliance on.

•The 2button will stop blinking and glow green.

•The rbutton will glow, to show that the boiler is operating.

•The Sbutton will blink, to show that steam is being generated.

•The #light will glow

26 Press the Sbutton to choose the steam level you want.

•The steam level lights are: S= low, ~= medium, #= high.

27 When the Sbutton glows steadily, the boiler is ready to make steam.

28 It’ll then cycle on and oﬀ as the boiler works to maintain the temperature.

29 If the temperature control on the iron is set above room temperature, the

thermostat light on the iron will glow, to show that the soleplate is heating up.

30 It’ll go out when the soleplate reaches the temperature set by the temperature

control, then cycle on and oﬀ, as the thermostat works to maintain the temperature.

CPRIMING

31 Prime the iron after ﬁlling the reservoir, to get water and steam through the system.

32 Hold the iron below the level of the base unit, and squeeze the steam trigger.

33 You’ll hear the pump as it pushes water through the system, then, after 30 seconds

or so, it’ll start to quieten, and steam will come out of the soleplate.

34 The iron is now primed and ready for use.

CAUTO-SHUT-OFF

35 If you don’t press the Sbutton and/or the shot of steam button for 8 minutes, the

appliance will go into standby mode.

36 To start again, jump to point 25.

CPREPARATION

37 Check for textile care symbols (ijkl).

38 Iron fabrics needing low temperatures jﬁrst, then those that need medium

temperatures k, and ﬁnish with those needing high temperatures l(or max).

CSET THE TEMPERATURE

39 Turn the temperature control to bring the setting you want next to the thermostat

light.

temperature setting guide

label marking temperature setting

jcool – nylon, acrylics, polyester •

kwarm – wool, polyester mixtures ••

lhot – cotton, linen •••

denim/jeans max

ido not iron

,If the instructions on the fabric label diﬀer from this guide, follow the instructions on

the label.

40 If the soleplate is at a lower temperature than the one you’ve set, the thermostat

light on the iron will glow, to let you know that the soleplate is heating up.

41 When the soleplate reaches operating temperature, the thermostat light will go out,

then cycle on and oﬀ as the thermostat works to maintain the temperature

CSTEAM IRONING

42 Set the temperature control to Sor higher – otherwise the steam might condense

on the soleplate, giving you water, instead of steam.

,When you ﬁrst want steam, you must prime the pump (opposite page).

43 Press the shot of steam button on top of the iron to produce steam, release it to

stop.

44 Don’t let the reservoir empty in use, or you’ll have to prime it again when you reﬁll it.

,Steam may still escape from the iron after you release the shot of steam button. This

is normal, don’t worry about it.

CCONSTANT STEAM

45 For a constant stream of steam, press the shot of steam button, then slide the lock at

the rear of the button back, towards the rear of the iron, to lock the button down.

46 Slide the lock forward, to unlock it, and revert to normal use.

CDRY IRONING

47 Press the rbutton (its light will go out), to switch the boiler oﬀ.

•The Sbutton and the steam level lights will all go out.

48 We recommend doing your dry ironing ﬁrst.

,It’s unlikely, but if you’re dry ironing for more than 8 minutes, the auto-shut-oﬀ

feature will operate.

CVERTICAL STEAMING

49 Remove wrinkles from hanging clothes, hanging curtains, and furnishing fabrics.

50 Check that there’s adequate ventilation behind the fabric, otherwise moisture may

build up, causing mildew.

51 Check that there’s nothing behind the fabric that may be damaged by the steam.

52 Check that pockets, turn-ups, and cuﬀs are empty.

53 Check that the steam ready light is glowing.

54 Set the temperature control to max.

55 Wait till the thermostat light goes out, then start steaming.

56 Hold the iron close to (but not touching) the fabric.

,Hold it well away for delicate fabrics.

57 Press the shot of steam button to produce steam, release it to stop the steam.

CLOW WATER

58 The low water light will glow if the water level gets low, or if the reservoir is not

correctly ﬁtted.

59 Fill the reservoir (see “FILLING”, on page 3), then prime the iron again.

CAFTER USE

60 Set the iron on the base unit.

61 Press the 2button – it will blink red.

62 Unplug the base unit (switch the socket oﬀ ﬁrst, if it’s switchable).

CCARE AND MAINTENANCE

1 Unplug the base unit, and let it and the iron cool down fully.

2 Wipe outer surfaces with a damp cloth. If necessary, use a little washing-up liquid.

3 Remove spots from the soleplate with a little vinegar.

4 Take care not to scratch the soleplate.

5 Lift the iron oﬀ the base unit, wind the steam pipe into its niche above the reservoir

and cable storage, then set the iron back on the base unit.

6 Open the cable storage, replace the plug and cable, and close the cable storage.

CTHE ANTI-SCALE CARTRIDGE

7 To reduce scale build-up, you must change the anti-scale cartridge regularly.

8 After 10 hours of steaming, the Olight will glow to tell you that the cartridge

needs to be replaced, and the boiler needs to be descaled.

9 Press the 2button and hold it down for 5 seconds, to turn oﬀ the Olight.

CCHANGING THE ANTI-SCALE CARTRIDGE

10 Switch oﬀ (2), unplug, and let the appliance cool down completely (at least 2 hours).

11 Lock the iron on top of the base unit.

12 Remove the reservoir.

13 Spread a towel on the work surface in the kitchen, as you’re likely to spill a bit, and

you’ll need access to water and a sink (or a basin).

14 Turn the whole appliance on its side, with the underside towards you.

15 Open the door of the compartment, and pull the anti-scale cartridge out.

16 Fit the new cartridge into the compartment, then close the compartment door.

17 Turn the appliance upright.

18 Descale the boiler

CDESCALING THE BOILER

19 Descale the boiler every time you replace the anti-scale cartridge.

20 Mix 1 tablespoon of white vinegar and 2 tablespoons of warm water in a jug.

21 Unscrew the boiler access knob, to expose the boiler pipe.

22 Pick the base unit up, and empty the boiler into the sink.

23 Turn the appliance on its side, and pour the vinegar/water mix into the pipe.

24 Replace the boiler access knob, and tighten it up.

25 Shake the appliance from side to side, to ensure the mixture coats the whole of the

inside of the boiler.

26 Leave it for half an hour.

27 Unscrew the boiler access knob, and pour the mixture into the sink.

28 Rinse the boiler with fresh water, to remove scale and vinegar:

29 Keep rinsing till the water that comes out is clear, free of scale particles, and doesn’t

smell of vinegar.

30 Finally, replace the boiler access knob, replace the reservoir, wipe up any spillage,

and store the appliance away.

,Products returned under guarantee with faults due to scale will be subject to a

repair charge.

CREPLACEMENT ANTI-SCALE CARTRIDGES

31 Have the appliance Model No. 20330 to hand, to ensure you get the right cartridge.

It’s also marked on the rating plate (usually underneath the product).

32 Visit www.russellhobbs.co.uk to purchase replacement cartridge(s).

552-829

WENVIRONMENTAL PROTECTION

To avoid environmental and health problems due to hazardous substances in

electrical and electronic goods, appliances marked with this symbol mustn’t be

disposed of with unsorted municipal waste, but recovered, reused, or recycled.

SSERVICE

If you ring Customer Service, please have the Model No. to hand, as we won’t be able

to help you without it. It’s on the rating plate (usually underneath the product).

The product isn’t user-serviceable. If it’s not working, read the instructions, check the

plug fuse and main fuse/circuit breaker. If it’s still not working, consult your retailer.

If that doesn’t solve the problem – ring Customer Service – they may be able to oﬀer

technical advice.

If they advise you to return the product to us, pack it carefully, include a note with your

name, address, day phone number, and what’s wrong. If under guarantee, say where

and when purchased, and include proof of purchase (till receipt). Send it to:

Customer Service

Spectrum Brands (UK) Ltd

Fir Street, Failsworth, Manchester M35 0HS

email: support@russellhobbs.com

telephone: 0845 658 9700 (local rate number)

EGUARANTEE

Defects aﬀecting product functionality appearing within two years of ﬁrst retail

purchase will be corrected by replacement or repair provided the product is used and

maintained in accordance with the instructions. Your statutory rights are not aﬀected.

Documentation, packaging, and product speciﬁcations may change without notice.

JONLINE/SPARES

www.russellhobbs.co.uk for more products and/or spares

IREGISTER ONLINE FOR –

r£10,000 prize draw,

EXTRA year guarantee,

FREE rewards gallery

Visit www.productregister.co.uk/rhobbs

You must register within 28 days of purchase.

Otros manuales para EASY

Tabla de contenidos

Otros manuales de Hierro de Russell Hobbs

Russell Hobbs

Russell Hobbs Turbo Steam RHC925 Manual de instrucciones de instalación

Russell Hobbs

Russell Hobbs Rapidsteam RHC902 Manual de instrucciones de instalación

Russell Hobbs

Russell Hobbs 14845 Guía de instalación

Russell Hobbs

Russell Hobbs 14033 Manual de usuario

Russell Hobbs

Russell Hobbs SteamGlide Manual de usuario

Russell Hobbs

Russell Hobbs 20562-56 Manual de usuario

Russell Hobbs

Russell Hobbs 19840AU Manual de instrucciones de instalación

Russell Hobbs

Russell Hobbs 15131 Manual de usuario

Russell Hobbs

Russell Hobbs RHI2000 Guía

Russell Hobbs

Russell Hobbs 14584 Guía de instalación

Russell Hobbs

Russell Hobbs 24420-56 Manual de usuario

Russell Hobbs

Russell Hobbs RHI 102 Guía de instalación

Russell Hobbs

Russell Hobbs SmartGlide PRo Manual de usuario

Russell Hobbs

Russell Hobbs RHI336C Guía de instalación

Russell Hobbs

Russell Hobbs 26020-56 Manual de usuario

Russell Hobbs

Russell Hobbs 25090-56 Manual de usuario

Russell Hobbs

Russell Hobbs STEAMGLIDE ULTRA RHC940 Guía de instalación

Russell Hobbs

Russell Hobbs SLIDE FILL GO SMARTFILL 21262 Manual de usuario

Russell Hobbs

Russell Hobbs SMOOTH IQ PLUS RHC700 Manual de instrucciones de instalación

Russell Hobbs

Russell Hobbs RHSIR 127V Manual de usuario

Russell Hobbs

Russell Hobbs RHECOI Guía

Russell Hobbs

Russell Hobbs 12290 Guía de instalación

Russell Hobbs

Russell Hobbs 23971-56 Manual de usuario

Russell Hobbs

Russell Hobbs 15002 Manual de usuario

Manuales populares de Hierro de otras marcas

Clatronic

Clatronic DB 3703 Manual de usuario

TEFAL

TEFAL FV4093Z0 Manual de usuario

Gorenje

Gorenje SIH 2200 BS Manual de usuario

Philips

Philips GC6012 Manual de usuario

Bosch

Bosch 2 Series Manual de usuario

Riffel

Riffel Catena KB-819 Manual de usuario

Texi

Texi Hestia Manual de usuario

Maxwell

Maxwell MW-3010 Manual de usuario

TREVIDEA

TREVIDEA Girmi ST60 Manual de usuario

Philips

Philips HI5914/30 Manual de usuario

Primula

Primula Vapormat Manual de usuario

Magio

Magio MG-541 Manual de usuario

Scarlett

Scarlett SC-1334S Manual de usuario

Bosch

Bosch Sensixx B22L Manual de usuario

Philips

Philips GC651 Manual de usuario

Vitek

Vitek VT-1247 VT Manual de usuario

Cleanmaxx

Cleanmaxx 3397 Manual de usuario

Philips

Philips GC800 Manual de usuario