Royal Sovereign RSC-165C Manual de usuario

www.royalsovereign.com

ROLL LAMINATOR

ROLL LAMINATOR ROLL LAMINATOR

ROLL LAMINATOR

Service Manual

Service Manual Service Manual

Service Manual

2 ~ 2

3 ~ 7

3 ~ 4

4 ~ 5

5 ~ 6

6 ~ 7

8 ~ 11

8 ~ 9

9 ~ 9

9 ~ 10

10 ~ 10

10 ~ 11

11 ~ 11

12 ~ 12

13 ~ 13

14 ~ 25

14 ~ 17

18 ~ 21

22 ~ 25

26 ~ 48

27 ~ 33

34 ~ 40

41 ~ 47

48 ~ 55

4. Adjustments

……………………………………………………………………………………

4.1) Adjusting Take-Up Shaft Speed ……….…………………………………………………………

4.2) Adjusting Front Roller ……………………………………………………………………………

5. Installation of Options

……………………………………………...……………………

6. Parts List

…………………………………………………………………………………………

6.1) RSC-1650C Parts List ………………………………………………………………………………

6.2) RSC-1650H Parts List ……………………………………………………………………………

7. Exploded Drawings

………………………………………………………………………

6.3) RSC-1650HR Parts List ……………………………………………………………………………

7.1) RSC-1650CF Whole Exploding Drawing and Part Exploding Drawing ……………………

7.2) RSC-1650HF Whole Exploding Drawing and Part Exploding Drawing ……………………

8. Wire Diagram

…………………………………………………………………………………

7.3) RSC-1650HRF Whole Exploding Drawing and Part Exploding Drawing ……………………

3.4) Main PCB ……………………………………………………………………………………………

3.5) Sub PCB ………………………………………………………………………………………………

3.6) Heaters ………………………………………………………………………………………………

3.7) Cross Cutter …………………………………………………………………………………………

3. Replacing Parts

………………………………………………………………………………

3.1) Right Cover …………………………………………………………………………………………

3.2) Left Cover …………………………………………………………………………………………

3.3) Rear Cover …………………………………………………………………………………………

2.1) Rollers Not Heating ………………………………………………………………………………

2.2) Rollers Over Heating ………………...……………………………………………………………

2.3) Rollers Not Running ……………….………………………………………………………………

2.4) No Main Power ……………………..………………………………………………………………

Table of Contents

1. Safety Precautions

………………………………………………………………………

2. Troubleshooting

……………………………………………………………………………

3 ~ 7

9 ~ 10

10 ~ 11

11 ~ 11

12 ~ 12

13 ~ 13

14 ~ 21

14 ~ 17

18 ~ 21

22 ~ 36

1. Safety Precautions

Safety Precaution

Failure to comply any of the following safety procedures could result in serious injury.

Please read the instructions carefully and keep for future reference.

1. Only a licensed electrician should install wiring and outlet for the laminator.

2. Ensure the unit is plugged into a properly grounded outlet with the correct

voltage.

3. Keep hands and clothing (ie.Neckties) away from the rollers. The rollers have pinch

points that can trap body parts or clothing and cause serious injury.

4. Keep flammable and wet objects away from the machine.

5. Place machine on a level surface.

6. Avoid excessive sunlight, humidity and extreme temperatures.

7. Ensure the unit is turned off, cooled, and unplugged from the outlet prior to

moving and/or repairing.

8. Keep out of reach of children.

9. Only Royal Sovereign authorized maintenance and service technicians should

make repairs.

10. Do not attempt to laminate items that exceed total recommended material

thickness for the unit.

11. When cleaning the machine, don't use flammable sprays or materials.

12. Do not touch the rollers when they are hot or place foreign objects inside the

machine.

13. Do not cover the surface of the machine until the machine has completely cooled.

2.1 Rollers Not Heating

(

RSC-1650H / HR Only

)

1. Disconnected Heater Wire.

2. Defective T/Fuse.

3. Defective Bi-metal.

4. Defective Heater Assembly.

5. Defective Main PCB.

NOTE: Below steps require you to disassemble the Right, Left,

1. Disconnected Heater Wire.

a) Check to make sure that the heater wire is connect to the Main PCB. Figure 1

2. Defective T/Fuse.

a) Use the multi-tester to check the continuity on the "Wire-T/Fuse".

If it fails replace the Wire-T/Fuse. Figure 2

23 ~ 29

30 ~ 36

37 ~ 42

2. Troubleshooting

CAUSES

MEASURES

Follow the below steps in order.

and/or Rear Covers. (Refer to the "Replacing Parts" section)

WIRE-T/FUSE

Figure 2

Heater Wires

Figure 1

a) Use the multi-tester to test the continuity on the "Bi-Metal".

If it fails replace it with a new one. Figure 3

4. The heater in the roller is defective.

a) Use a multi-tester to test the continuity on the "Heater Assembly". If it

fails replace the Heater Assembly. Figure 4

a) Replace Main PCB.

2.2) Rollers Over Heating

(

RSC-1650H / HR Only

)

1. The temperature sensor wire is improperly connected to the SUB-PCB.

2. Defective Heater Assembly

3. Main PCB is defective

1. If the temperature sensor wire is improperly connected to the SUB-PCB.

a) Unplug the temperature sensor wire and reconnect it properly. Figure 1

5. Main PCB is defective

3. The Bi-metal is defective.

MEASURES

CAUSES

Bi-metal

Figure 3

HEATER

Figure 4

WIRE

SENSOR

Figure 1

2. Defective Heater Assembly

a) Replace the broken Heater Assembly. Figure 2

3. Main PCB is defective

a) Replace Main PCB.

2.3) Rollers Not Running

1. Emergency Switches are Active.

2. Pressure Plate is not in Proper Position.

3. Film is Jammed on the Rollers.

4. Main Motor Wires are Disconnected.

5. Defective Main PCB.

6. Defective Main Motor.

1. Emergency Switch is (are) Active.

2. Pressure Plate is not in Proper Position.

a) Ensure that the Pressure Plate is in the proper position and the

Pressure Plate switch is active. Figure 1

3. Film is Jammed on the Rollers.

a) Carefully un-jam the film from the rollers.

CAUSES

a) Deactivate front and rear emergency switches.

MEASURES

Broken

Figure 2

P P t t hressure la e Swi c

Figure 1

4. Main Motor Wires are Disconnected.

a) Ensure that the wire is connected properly. Figure 2

5. Defective Main PCB.

a) Replace the Main PCB.

6. Defective Main Motor.

a) Replace the Main Motor.

2.4) No Main Power

1. Main Power is Not Turned On.

2. No Power from the Outlet.

3. Defective Main Fuse.

4. Control Panel (Sub-PCB) Wire is Not Connected.

5. Disconnected Main Power Wire.

6. Defective Transformer.

1. Main Power is Not Turned On.

a) Turn on the power switch which is located on the rear left.

2. No Power from the Outlet.

a) Ensure there is power on the outlet - check the circuit breaker.

3. Defective Main Fuse.

a) Using Multi-Meter test the continuity of the Main Fuse. If it fails, replace it. Figure 1

< RSC-1650HR MAIN PCB Layout >

CAUSES

MEASURES

Motor wire connector

from the Motor Motor wire connector

from the PCB

Figure 2

Main

use

Figure 1

4. Control Panel (Sub-PCB) Wire is Not Connected.

a) Ensure that the control wires are connected to the Control Panel (Sub-PCB).

5. Disconnected Main Power Wire.

a) Connect the Main Power wires. Figure 2

6. Defective Transformer.

a) Replace the Transformer. Figure 3

Transformer

Figure 3

Main Power wires

Figure 2

NOTE : Before replacing any parts, ensure that the machine is turned off and

3.1 Right Cover

1. Using Philips Screw Driver, loosen the screw on the Pressure Lever. Figure 1

2. Take out the four screws as shown in Figure 2.

3. Disconnect the temperature sensor (RSC-1650H / HR only) and control wires

from the Sub-PCB. Figure 3

3. Replacing Parts

unplugged from the outlet.

Figure 1

Figure 2

Figure 3

4. Take out two Sub-PCB screws. Figure 4

5) Repeat the steps in reverse to assemble the Right Cover.

3.2 Left Cover

1. Take out four screws on the Left Cover.

3.3 Rear Cover

1. Disassemble the Left and Right Covers.

2. Take out the side screws - one on each side. Figure 5

3. Loosen eight Rear Cover screws. Figure 5

3.4 Main PCB

1. Pull out all the connectors from the main PCB. Figure 6

Figure 4

Figure 5

Figure 6

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Laminadora de Royal Sovereign

Royal Sovereign

Royal Sovereign Quick Ready APL-340U Manual de usuario

Royal Sovereign

Royal Sovereign APL-230 Manual de usuario

Royal Sovereign

Royal Sovereign ES-1310 Manual de usuario

Royal Sovereign

Royal Sovereign RSC Series Manual de usuario

Royal Sovereign

Royal Sovereign EL-9DF Manual de usuario

Royal Sovereign

Royal Sovereign RSL2701S Manual de usuario

Royal Sovereign

Royal Sovereign HSH-1300 Manual de usuario

Royal Sovereign

Royal Sovereign RSH-380 Manual de usuario

Royal Sovereign

Royal Sovereign RSL-382CR Manual de usuario

Royal Sovereign

Royal Sovereign RSC-820CL Manual de usuario

Royal Sovereign

Royal Sovereign RSC-1650C Manual de usuario

Royal Sovereign

Royal Sovereign ES-1315 Manual de usuario

Royal Sovereign

Royal Sovereign NPH-1200N Manual de usuario

Royal Sovereign

Royal Sovereign NR-1201 Manual de usuario

Royal Sovereign

Royal Sovereign ES-1300C Manual de usuario

Royal Sovereign

Royal Sovereign RSC-1401CLTW Manual de usuario

Royal Sovereign

Royal Sovereign RSC-LS series Manual de usuario

Royal Sovereign

Royal Sovereign RHD-2201 Manual de usuario

Royal Sovereign

Royal Sovereign RSC-880LS Manual de usuario

Royal Sovereign

Royal Sovereign RSC-1651LS/LSH Manual de usuario

Royal Sovereign

Royal Sovereign RSL1062 Manual de usuario

Royal Sovereign

Royal Sovereign PL - 922 Manual de usuario

Royal Sovereign

Royal Sovereign PL-1310 Manual de usuario

Royal Sovereign

Royal Sovereign RSC-820CL Manual de usuario

Manuales populares de Laminadora de otras marcas

Renz

Renz HT 330 L Manual de usuario

Gfp

Gfp 44TH Manual de usuario

Lapis

Lapis Lamina006 Manual de usuario

Hama

Hama L44B Manual de usuario

PAVO

PAVO FLORIDA Manual de usuario

M-Triangel

M-Triangel MT-102 Manual de usuario

Akiles

Akiles PROLAM 230 Manual de usuario

D&K

D&K Masterpiece 550 Manual de usuario

Falcon

Falcon F-40 Manual de usuario

LEITZ

LEITZ EasyLaminator A4 Manual de usuario

LEITZ

LEITZ coldLAM CS9 Manual de usuario

kala

kala Starter 1080 Manual de usuario

Fellowes

Fellowes Venus A3 Manual de usuario

Qomolangma

Qomolangma FMJ-1400-WA-PLUS Manual de usuario

Opus

Opus Coverator 330 Manual de usuario

ALDI

ALDI OL 250-L Manual de usuario

Phoenix

Phoenix 2700-DH Manual de usuario

acropaq

acropaq AL-3400 Manual de usuario