Rough country 10499 Guía de configuración

Thank you for choosing Rough Country for all your vehicle needs.

Please read instructions before beginning installation. Check the kit hardware against the kit contents shown below. Be

sure you have all needed parts and know where they go.

If question exist, please call us @1-800-222-7023. We will be happy to answer any questions concerning this product.

Check all fasteners for proper torque. Check to ensure for adequate clearance between all components.

Check and retighten wheels at 50 miles and again at 500 miles. Periodically check all hardware for tightness.

KIT CONTENTS:

Dr & Pass Outer Inner Fender

Dr & Pass Rear Inner Fender

Dr & Pass Front Bracket

Dr & Pass RC logo plate

Red Accents x2

TOOLS NEEDED:

4mm Allen

8mm Socket

10mm Wrench and Socket

Jack

Jack Stands

Rachet

Body Saw

Paint marker

Tape measure

Auto Trim Puller

Long nose plyers

Wheel Chocks

HARDWARE INCLUDED:

(20) 6mm-1.0 x20 Button Head Bolts

(8) 6mm-1.0 x20 Hex Head Bolts

(2) 6mm-1.0 x35 Hex Head Bolts

(12) 6mm Nylock Nut

(18) 6mm Body clips

(42) 6mm Flat Washers

Torque Specs:

Size Grade 5 Grade 8 Size Class 8.8 Class 10.9

5/16” 15 ft/lbs 20ft/lbs 6MM 5ft/lbs 9ft/lbs

3/8” 30 ft/lbs 35ft/lbs 8MM 18ft/lbs 23ft/lbs

7/16” 45 ft/lbs 60ft/lbs 10MM 32ft/lbs 45ft/lbs

1/2” 65 ft/lbs 90ft/lbs 12MM 55ft/lbs 75ft/lbs

9/16” 95 ft/lbs 130ft/lbs 14MM 85ft/lbs 120ft/lbs

5/8” 135ft/lbs 175ft/lbs 16MM 130ft/lbs 165ft/lbs

3/4” 185ft/lbs 280ft/lbs 18MM 170ft/lbs 240ft/lbs

JEEP 2018-19 JL Front Inner Fenders

921104970

Passengers Side Front Mounting Bracket (x1)

Drivers Side Front Mounting Bracket (x1)

Drivers and Passengers Front mounting

brackets. Use this edge to set the mounting

angle onto the body mount. See Step 32.

and Photo 31.

Use this edge to set the mounting angle.

INSTALLATION INSTRUCTONS FOR STEP 32.

1. Park the vehicle on a level surface and chock the rear wheels.

2. Jack up the front of the vehicle. Place jack stands under the frame rails and lower onto jack stands letting the front

suspension hang.

3. Remove the tires and wheels using a 19mm socket.

4. Remove the 2 small screws from the front of the fender liner, using a 8mm socket. See Photo 1. Save for reuse.

5. Remove the 2 bolts from the top of the fender liner, using a 10mm socket. See Photo 2. Save for reuse.

6. Using an auto trim puller, remove the 2 push pins in the front and the 3 in the top center of the fender liner. See

Photo 3 and 4.

7. Using a auto trim puller, remove the rear 2 push pins in the rear lower fender liner. See Photo 5.

8. Release the fender liner from the 3 plastic rivets on the edge of the fender, use an auto trim puller to help release.

See Photo 6. Leave the 3 rivets in the fender.

Photo 1 Photo 2

Photo 3 Photo 4

Photo 5 Photo 6

Remove 2 small screws. Remove 2 bolts.

Remove 2 push pins. Remove 3 push pins.

Remove 2 rear push pins. Release fender liner from fender.

INSTALLATION INSTRUCTONS

9. Remove the fender liner. Set aside this will not be reused. See Photo 7.

10. Located at the front of the fender remove the 2 bolts, using a 10mm socket. See Photo 8. Save for reuse.

11. Pull the red locking tab back, push the clip and disconnect the light wiring harness from the jeep. See Photo 9.

12. Using care not to break any clips, these will be reused to install the fender back onto the vehicle, release the 11 clips

from the back side of the fender, use long nose plyers. See Photo 10.

13. Once all of the clips are released from the back side, remove fender, set in a safe place for modification. See Photo

11.

14. Removing clips, please make note of the arrows in Photo 12, from the front of the fender back remove the 3rd and

4th clip, 7th and 11th clip, from the fender. See Photo 12.

Photo 7 Photo 8

Photo 9 Photo 10

Photo 11 Photo 12

Remove fender liner. Remove 2 bolts at the front of the fender.

Disconnect the light wiring harness. Release clips to remove fender.

Remove fender. Remove noted clips.

11th clip

7th clip

3rd and 4th clip

15. Release the tabs in between the fender and remove the 3rd and 4th clips. See Photo 13.

16. Remove the 7th and 11th clip on the rear and bottom of the fender. See Photo 14.

17. Using an auto trim puller remove the push pins attached to the wiring harness running through the top of the fender.

See Photo 15.

18. Mark the area to be removed behind the 3rd and 4th clip openings in the top of the fender, mark just behind the

raised area in the 3rd hole and mark a 1” wide area on the 4th hole to be trimmed out for bolt and tool access for

installation of the inner fenders. See Photo 16.

19. Trim marked area’s using a body saw. See Photo 17.

20. After trimming the marked area’s smooth any jagged parts using a file or sand paper. See Photo 18.

Photo 13 Photo 14

Photo 15 Photo 16

Photo 17 Photo 18

Remove clips. Remove clips.

Remove wiring harness. Mark 1”and cut out.

Trim marked area only. See removed area.

Mark and cut off.

DO NOT CUT INTO OUTSIDE OF FENDER.

11th clip

7th clip

3rd and 4th clips

21. Mark the 3 highlighted lines on the inner structure to be trimmed for bolt and tool access. See Photo 19.

22. Using a body saw trim the 3 highlighted lines on the inner structure. See Photo 20.

23. Remove trimmed part from fender and discard. See Photo 21. After trimming the marked area’s smooth any jagged

parts using a file or sand paper.

24. Reclip the wire back into the original location, install the fender back onto the vehicle, secure using the clips on the

back of the fender into there original holes. See Photo 22.

25. The kit picture below is to show were the 6mm body clips go and their appropriate hardware. See Photo 23.

Photo 19 Photo 20

Photo 21 Photo 22

Mark lines to be trimmed. Trim out inner structure.

Remove inner structure. Reclip the wire to fender and install fender.

Photo 23

View placement of the 6mm body clips.

Pass Rear Inner Fender

Pass Outer Inner Fender

Pass Front Bracket

Pass RC logo plate

Red Accent

26. Install the (6) 6mm body clips onto the rear inner fender panel. See Photo 24.

27. Install the rear inner fender panel into the rear of the vehicle. See Photo 25.

28. Secure the rear inner fender to the vehicle using the supplied 6mm-1.0x 20mm Hex head bolt and 6mm washer, use

a 10mm wrench to tighten. See Photo 26 and 27.

29. Locate the front inner fender bracket, 6mm body clip, 6mm-1.0x 35mm hex head bolt, (2) 6mm washers and 6mm

nylock nut , install the 6mm clip onto bracket. See Photo 28.

30. Remove the bolt located on the front body mount. See Photo 29.

Photo 24 Photo 25

Photo 26 Photo 27

Photo 28 Photo 29

Install (6) 6mm clips onto the back panel. Install rear panel.

Install bolt in empty upper clip location. Install bolt in empty lower clip location.

Install on the clip on inner fender bracket. Remove stock bolt.

31. Install the 6mm-1.0x35mm bolt and washer into the location of the original bolt making a mounting point for the inner

fender bracket, use a 10mm socket to tighten. See Photo 30.

32. Install the inner fender mounting bracket onto the installed 6mm-1.0x35mm bolt, seat the bracket onto the nut on the

bottom of the body mount bracket, Described on the 2nd page of this instruction sheet. Use the edge to set the

mounting angle onto the body mount. Tighten using a 10mm wrench. See Photo 31.

33. Install the (2) 6mm body clips onto the inner fender panel on the top of the mounting point. See Photo 32.

34. Only install the (5) 6mm-1.0 x20mm bolts, washers and nylock nuts. if your installing these inner fenders with the

Rough Country Vertex shocks installed on the vehicle. If so tighten using a 4mm allen wrench and a 10mm socket

on the nut, turn the nut only to prevent chipping the powder coat off of the outside. See Photo 33. Do not install logo

panel at this time.

35. Install the outside panel onto the vehicle, using (2) Hex head 6mm-1.0 x20mm bolts and washers, Snug the 2 bolts

using a 10mm wrench. See Photos 34 and 35.

Photo 30 Photo 31

Photo 33

Photo 34 Photo 35

Install the 6mm-1.0x35mm bolt and washer Install the inner fender mounting bracket.

Install bolts for vertex shocks only.

Install panel and the (2) 6mm bolts. Snug the (2) bolts.

Photo 32

Install 6mm clips in the top of panel.

36. Install the (4) 6mm-1.0 x20mm button head bolts and washers in the rear of the panel. See Photo 36.

37. Install the (1) 6mm-1.0 x20mm button head bolt and washers in the front of the panel. See Photo 37.

38. Tighten the top center 2 bolts installed in photo 34 and 35. using a 10mm wrench.

39. Install the 2 factory screws in the front of the fender, tighten using an 8mm socket. See Photo 38.

40. Install the 4 factory bolts into the fender, tighten using a 10mm. See Photo 39.

41. Connect the wiring harness into the factory plug, push in the red locking tab. See Photo 40.

42. Peal the protective cover off of the red accent. See Photo 41.

Photo 36 Photo 37

Photo 38 Photo 39

Photo 40 Photo 41

Install the (4) 6mm bolts and washers. Install the (1) 6mm bolt and washer.

Install and tighten the front 2 OE bolts. Install and tighten the 4 OE bolts.

Plug the light wire back into the harness. Peal off the protective cover.

43. Locate the RC logo plate, peal the covering from the double sided tape on the front side of the red accent, align the

red accent over the RC logo securing the accent to the RC logo plate with the double sided tape. See Photo 42.

44. Install the RC logo plate into the outside panel. See Photo 43.

45. Secure the RC logo plate to the outside panel, using the supplied 6mm-1.0 x20mm button head bolts, washers and

nylock nuts. Turn the nut to tighten the bolts to prevent any powder coat damage. See Photo 44.

46. Repeat steps on opposite side. Check all hardware to be tight. See Photo 45.

47. Install the front wheels and tires, tighten using a 19mm socket.

48. Lift the vehicle up and remove the jack stands, then lower the vehicle back onto the ground.

By purchasing any item sold by Rough Country, LLC, the buyer expressly warrants that he/she is in compliance with all

applicable , State, and Local laws and regulations regarding the purchase, ownership, and use of the item. It shall be

the buyers responsibility to comply with all Federal, State and Local laws governing the sales of any

items listed, illustrated or sold. The buyer expressly agrees to indemnify and hold harmless Rough

Country, LLC for all claims resulting directly or indirectly from the purchase, ownership, or use of the

items.

Photo 42 Photo 43

Photo 44 Photo 45

Install accent onto RC logo plate. Install RC logo plate into outside panel.

Tighten logo plate. Check all bolts to be tight.

Otros manuales de Accesorios para automóviles de rough country

rough country

rough country 47120580 Manual de usuario

rough country

rough country 70213 Manual de usuario

rough country

rough country 10538 Manual de usuario

rough country

rough country 70101 Manual de usuario

rough country

rough country RC-O5 Manual de usuario

rough country

rough country 928511900 Manual de usuario

rough country

rough country RC-W5 Manual de usuario

rough country

rough country 70217 Manual de usuario

rough country

rough country 927061900 Manual de usuario

rough country

rough country 51006BAG1 Manual de usuario

rough country

rough country 1118517 Manual de usuario

rough country

rough country 92179500000 Manual de usuario

rough country

rough country 921707820 Manual de usuario

rough country

rough country 31007 Manual de usuario

rough country

rough country 92705360 Manual de usuario

rough country

rough country 921106090 Manual de usuario

rough country

rough country HEC70186 Manual de usuario

rough country

rough country 92130300 Manual de usuario

rough country

rough country RC-X5 Manual de usuario

rough country

rough country 921510090 Manual de usuario

rough country

rough country SOFT ROLL UP TRUCK BED COVER Manual de usuario

rough country

rough country RCH5100 Manual de usuario

rough country

rough country 99003 Manual de usuario

rough country

rough country Triple Fog Light Mounting Kit Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario

rough country 10499 Guía de configuración

Manuales populares de Accesorios para automóviles de otras marcas