Rough country 10538 Manual de usuario

Thank you for choosing Rough Country for all your vehicle needs.

Please read instructions before beginning installation. Check the kit hardware against the kit contents shown below. Be

sure you have all needed parts and know where they go.

If question exist, please call us @1-800-222-7023. We will be happy to answer any questions concerning this product.

Check all fasteners for proper torque. Check to ensure for adequate clearance between all components.

Periodically check all hardware for tightness.

Check your local and state laws regarding fender and tire coverage requirements.

KIT CONTENTS:

1-Front Drivers Side Fender Delete

1-Front Pass Side Fender Delete

1-Rear Drivers Side Fender Delete

1- Rear Pass Side Fender Delete

1-10536BAG

1-10537BAG

TOOLS NEEDED:

10mm socket

4mm allen Wrench

5mm allen Wrench

13mm Wrench

Rachet

1/8” Drill

5/16” Drill

Drill Motor

1/8” Punch

Hammer

3/8” or W Drill

HARDWARE INCLUDED:

10536BAG:

16-8mm-1.25 X 25MM BHCS

16-8mm FLAT WASHER

16-8mm-1.25 Nylock Nut

2-6mm-1.0 X 20mm BHCS

2-6mm Flat Washer

10537BAG:

18-6mm-1.0 X 20mm BHCS

26-6mm Flat Washer

12-6mm X 1 Blind Nut Insert

6-6mm-1.0 Nylock Nut

1-6MM-1.0 X 40MM HHCS

2-5/16-18 Hex Nut

Torque Specs:

Size Grade 5 Grade 8 Size Class 8.8 Class 10.9

5/16” 15 ft/lbs 20ft/lbs 6MM 5ft/lbs 9ft/lbs

3/8” 30 ft/lbs 35ft/lbs 8MM 18ft/lbs 23ft/lbs

7/16” 45 ft/lbs 60ft/lbs 10MM 32ft/lbs 45ft/lbs

1/2” 65 ft/lbs 90ft/lbs 12MM 55ft/lbs 75ft/lbs

9/16” 95 ft/lbs 130ft/lbs 14MM 85ft/lbs 120ft/lbs

5/8” 135ft/lbs 175ft/lbs 16MM 130ft/lbs 165ft/lbs

3/4” 185ft/lbs 280ft/lbs 18MM 170ft/lbs 240ft/lbs

JEEP 2007-18 JK Fender Delete Kit

921105380

1. Removing the front fenders.

2. Disconnect the side parking light wire from the fender. See Photo 1.

3. Remove the bolt in the fender bracket. Using a 10mm socket. See Photo 2.

4. Remove the bolt in the front inner fender well, using a 10mm socket. See Photo 3.

5. Remove the 2 bolts on the bottom side of the inner fender well, using a 10mm socket. See Photo 4. Retain factory

hardware for reuse.

6. Remove the rear bolt in the fender well, using a 10mm socket. See Photo 5. Retain factory hardware for reuse.

7. Remove the fender from the jeep.

8. To release the inner fender well from the outside fender, use a punch or a 1/8” drill bit to remove the center of the

rivets in the fender well. See Photo 6.

Photo 1 Photo 2

Photo 3 Photo 4

Photo 5 Photo 6

Remove parking light. Remove fender bolt from bracket.

Remove fender bolt. Remove the inner fender bolt.

Remove inner fender bolt. Remove the rivets from inner fender.

INSTALLATION INSTRUCTONS

9. Remove the push pins attaching the fender well to the outer fender. See Photo 7.

10. Temporarily install the inner fender back into position. This can be done by using the factory hardware. Using a paint

marker trace a line from the fender onto the inner fender. See Photo 8.

11. Trace the front edge of the fender onto the inner fender while in the installed position. See Photo 9.

12. Remove the inner fender for trimming, retain factory hardware for reuse.

13. Trim along the line traced onto the inner fender. See Photo 10.

14. Trim along the bottom of the fender bracket, using a cut off wheel. See Photo 11.

15. Once the bracket has been cut remove from the vehicle. See Photo 12.

Photo 7 Photo 8

Photo 9 Photo 10

Photo 11 Photo 12

Remove push pins. Trace inner fender.

Trace front edge. Trim the overhung area away.

Cut fender bracket off. Remove fender bracket.

16. Sand and paint the trimmed area to prevent rust, use painters tape along the edge of the fender to prevent over-

spray from getting on the fender of the vehicle. See Photo 13.

17. Remove the bottom bolt in the fender, use a 10mm socket. See Photo 14.

18. Install the fender delete onto the vehicle using the (8) 8mm-1.25mmx25mm BHCS, washers and nuts. Use a 5mm

allen wrench and a 13mm wrench to tighten. See Photos 15-16.

19. Install the 6mm-1.0x20mm bolt and washer in the bottom hole of the fender, through the fender delete and stock

hole in the fender, use a 4mm allen wrench to tighten. See Photo 17.

20. Install the stock inner fender using OE hardware, tighten using a 10mm socket. Photo 18. Shown with the RC in-

ner fenders installed.

21. Repeat steps 1-20 on opposite side of the vehicle.

Photo 13 Photo 14

Photo 15 Photo 16

Photo 17 Photo 18

Prep area and paint. Remove bolt from lower fender.

Tighten bolts installed.

Install and tighten 6mm bolt. Install inner fender.

Install fender delete.

1. Remove the push pins from the inner fender well. See Photo 1. Save for reuse.

2. Remove the outer fender, pull from the bottom edge of the fender releasing each of the clips. See Photo 2. NOTE :

all but the top 2 clips are inside the body panel and cannot be reached.

3. To remove the inner fender well from the outside fender, use a punch or a 1/8” drill bit to remove the center of the

rivets in the fender well. See Photo 3.

4. Temporary install the inner fender back into position. This can be done by using the factory hardware. Using a paint

marker trace a line from the fender onto the inner fender. See Photo 4.

5. Remove the inner fender for trimming.

6. Trim along the line made onto the inner fender. See Photo 5.

7. Hold the fender delete up to the vehicle, using a paint marker, mark the mounting holes to identify the ones that

need to be drilled out. See Photo 6. NOTE: the top 2 center holes are accessible and will not need marked.

Photo 1 Photo 2

Photo 3 Photo 4

Photo 5 Photo 6

Remove push pins. Remove fender.

Remove inner fender. Trace fender well opening.

Trim the overhung area away. Mark holes in fender delete.

INSTALLATION INSTRUCTONS

8. Drill out the holes that are marked using a W or 3/8” drill bit. See Photo 7.

9. Install the nutserts using the supplied 6mm-1.0x40mm bolt, (2) 5/16-18 nuts, and (2) flat washers. Using a 10mm

Wrench on the bolt and a 1/2” Wrench to hold the bottom nut. See Photo 8.

10. Install the fender delete onto the vehicle, use the supplied 6mm-1.0x20mm bolts and washers in the nutserts, 6mm-

1.0x20mm bolts and washers in the center 2 bolts with washers and 6mm-1.0mm nuts on the back side of the fender

well.

11. Tighten all hardware installed using a 4mm allen wrench and a 10mm wrench. See Photo 9.

12. Using the bottom of the fender delete as a template, drill through the hole using a 5/16 drill. See Photo 10.

13. Install the supplied 6mm-1.0x20mm bolt washers and the 6mm-1.0 nut, tighten using a 4mm allen wrench and a

10mm wrench. See Photo 11.

14. Install the inner fender using the OE hardware. Photo shown with the RC inner fender kit installed. See Photo 12.

15. Repeat steps 1-14 on opposite side of the vehicle.

Photo 7 Photo 8

Photo 9 Photo 10

Photo 11 Photo 12

Drill holes in body for nutserts. Install nutserts.

Install and tighten hardware. Drill hole using 5/16 drill.

Install 6mm hardware and tighten. Install inner fender.

By purchasing any item sold by Rough Country, LLC, the buyer expressly warrants that he/she is in compliance with all

applicable , State, and Local laws and regulations regarding the purchase, ownership, and use of the item. It shall be

the buyers responsibility to comply with all Federal, State and Local laws governing the sales of any

items listed, illustrated or sold. The buyer expressly agrees to indemnify and hold harmless Rough

Country, LLC for all claims resulting directly or indirectly from the purchase, ownership, or use of the

items.

Tabla de contenidos

Otros manuales de Accesorios para automóviles de rough country

rough country

rough country 921107830 Manual de usuario

rough country

rough country 92705360 Manual de usuario

rough country

rough country 92179500000 Manual de usuario

rough country

rough country 31007 Manual de usuario

rough country

rough country 82000BAG1 Manual de usuario

rough country

rough country 99003 Manual de usuario

rough country

rough country 70213 Manual de usuario

rough country

rough country 921707010 Manual de usuario

rough country

rough country RC-U5 Manual de usuario

rough country

rough country Triple Fog Light Mounting Kit Manual de usuario

rough country

rough country 921707820 Manual de usuario

rough country

rough country 92PERF1641 Manual de usuario

rough country

rough country 92130300 Manual de usuario

rough country

rough country RC-O5 Manual de usuario

rough country

rough country Slim Line LED Light Grille Kit Manual de usuario

rough country

rough country 11826 Manual de usuario

rough country

rough country RC-G5 Manual de usuario

rough country

rough country RC-Z5 Manual de usuario

rough country

rough country 921106090 Manual de usuario

rough country

rough country 47120580 Manual de usuario

rough country

rough country JEEP 2017-19 WK2 Manual de usuario

rough country

rough country RCH5100 Manual de usuario

rough country

rough country 51006BAG1 Manual de usuario

rough country

rough country HEC70186 Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario

rough country 10538 Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas