ROSE DISPLAYS ANOFRAME VERSAMOUNT SCREW BASE SIDE LOAD Manual de usuario

Parts

35 Congress Street, Salem MA 01970

Tel# 1-800-631-9707 Fax# 1-800-560-2890

e-mail:signware@rosedisplays.com

AnoFrame VersaMountTM Screw Base

Step 1

Locate the two split rails and the solid

rail that is the same length as the split

rails.

Insert two corner brackets into each

end of the solid side Ano rail. Insert

one corner bracket into each end of

each split side Ano rail. Fig. 2

Note: Tension tabs on corner

brackets face towards outside of

frame. Fig. 1

Step 2

For ceiling application, slide screw

tabs into channel of top Ano rail. For

wall applications, slide into side Ano

rail. Fig. 3

Step 3

Place one transitional collar over each

screw tab and push onto frame. Fig. 4.

Step 4

Finish assembling frame following the

sequence in Fig. 5.

Note: Placement of split rails will

depend on type of frame. Split rails

will be on the top for top-loading

frames and on the side for side-

loading frames.

split rails

solid rail

Instructions For Assembly

Incept-9.6.02

Figure 1

The AnoFrame VersaMount is a trademark of Rose Displays, Ltd. Neither

the manufacturer nor any sales agent may be held liable for injury, loss

or damage resulting from the use of these products.

Part #02INSVersaMountScrewBaseSide

Figure 3

Corner

Brackets

AnoFrame

Rails

AnoFrame

Split Rails

Figure 2

Figure 4

Screw Tabs

Transitional

Collars Posts

Screw

Bases

Instruction Sheet (page 1 of 2)

solid rail

split rails

Figure 5

Wood Screws

or Togglebolts

Screws

#97-0451R

Parts

Step 5

Screw posts onto screw tabs and

tighten. Fig. 6

Note: Use the end of the post with

the smaller opening.

Step 6

Insert one screw through the middle

opening on each screw base and into

the posts. Fig. 7

Tighten with screwdriver. Fig 8

Step 7

Install screw bases using wood screws

and screwdriver. Fig. 9

Note: Togglebolts are recommended

for drywall installations (predrilling

3/8” holes is necessary)

Step 8

Slide your graphic into the AnoFrame.

Fig. 10

Instructions For Assembly

Incept-9.6.02

Figure 6

The AnoFrame VersaMount is a trademark of Rose Displays, Ltd. Neither

the manufacturer nor any sales agent may be held liable for injury, loss

or damage resulting from the use of these products.

Part #02INSVersaMountScrewBaseSide

Figure 7

Finished Look

35 Congress Street, Salem, MA 01970

Tel# 1- 800 631-9707 Fax# 1-800-560-2890

e-mail:signware@rosedisplays.com

Instruction Sheet (page 2 of 2)

AnoFrame VersaMountTM Screw Base

Figure 8 Figure 9

#97-0451R

Figure

Parts

AnoFrame VersaMountTM Screw Base

Step 1

Locate the two split rails and the solid

rail that is the same length as the split

rails.

Insert two corner brackets into each

end of the solid side Ano rail. Insert

one corner bracket into each end of

each split side Ano rail. Fig. 2

Note: Tension tabs on corner

brackets face towards outside of

frame. Fig. 1

Step 2

For ceiling application, slide screw

tabs into channel of top Ano rail. For

wall applications, slide into side Ano

rail. Fig. 3

Step 3

Place one transitional collar over each

screw tab and push onto frame. Fig. 4.

Step 4

Finish assembling frame following the

sequence in Fig. 5.

Note: Placement of split rails will

depend on type of frame. Split rails

will be on the top for top-loading

frames and on the side for side-

loading frames.

split rails

solid rail

Instructions For Assembly

Incept-9.6.02

Figure 1

The AnoFrame VersaMount is a trademark of Rose Displays, Ltd. Neither

the manufacturer nor any sales agent may be held liable for injury, loss

or damage resulting from the use of these products.

Part #02INSVersaMountScrewBaseSide

Figure 3

Corner

Brackets

AnoFrame

Rails

AnoFrame

Split Rails

Figure 2

Figure 4

Screw Tabs

Transitional

Collars Posts

Screw

Bases

Instruction Sheet (page 1 of 2)

solid rail

split rails

Figure 5

Wood Screws

or Togglebolts

Screws

#97-0451R

Parts

Step 5

Screw posts onto screw tabs and

tighten. Fig. 6

Note: Use the end of the post with

the smaller opening.

Step 6

Insert one screw through the middle

opening on each screw base and into

the posts. Fig. 7

Tighten with screwdriver. Fig 8

Step 7

Install screw bases using wood screws

and screwdriver. Fig. 9

Note: Togglebolts are recommended

for drywall installations (predrilling

3/8” holes is necessary)

Step 8

Slide your graphic into the AnoFrame.

Fig. 10

Instructions For Assembly

Incept-9.6.02

Figure 6

The AnoFrame VersaMount is a trademark of Rose Displays, Ltd. Neither

the manufacturer nor any sales agent may be held liable for injury, loss

or damage resulting from the use of these products.

Part #02INSVersaMountScrewBaseSide

Figure 7

Finished Look

Instruction Sheet (page 2 of 2)

AnoFrame VersaMountTM Screw Base

Figure 8 Figure 9

#97-0451R

Figure

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de ROSE DISPLAYS

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME ROUND ASSEMBLED-TOGGLEBOLTS Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME ROUND ASSEMBLED-SLATWALL Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME ROUND ASSEMBLED-MOLLY ANCHORS Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ADVANCETRAK WITH CABLE CLIP AND CABLE Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS RAN-BAS-CC WITH LOOP AND BALL Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS GOTCHA FOR PEGBOARD Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ANOGOTCHA PLUS WITH MULTICLIPS AND REGULAR... Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ANOGOTCHA ROUND WITH MULTICLIPS Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ANOSCREEN WITH BASE RAIL Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ANOMULTI WITH WINDOW MOUNTS Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS SUPERSNAP WITH MULTICLIPS Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS CABLE CLIP Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ANOGOTCHA SQUARE WITH CABLE CLIP AND BALL... Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS SUPERSNAP WITH CABLE AND BALL Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS SUPERSNAP WITH ROD, CABLE CLIP AND BALL... Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ANOQUICK ROUND WITH CABLE AND SAUCER Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ECONOSTAND WITH ANOGOTCHA Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS CLEVER WHATEVER Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS PIG TAIL Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ANOGOTCHA ROUND WITH CABLE AND SAUCER Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ANOQUICK WITH PEG Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS TOPPER CLIPS Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ANOMULTI ROUND WITH CABLE CLIP AND LOOP AND... Manual de usuario

ROSE DISPLAYS

ROSE DISPLAYS ANOGOTCHA SQUARE WITH WALL HANGERS Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario