Rockwell Automation SmartGuard 600 Manual de usuario
Installation Instructions
SmartGuard 600 Controllers
Catalog Numbers 1752-L24BBB, 1752-L24BBBE
Topic Page
Important User Information 2
North American Hazardous Location Approval 3
General Safety Information 3
About the SmartGuard 600 Controller 5
Before You Begin 7
Set the Node Address 7
Setting the Communication Rate 7
Set the IP Address for Ethernet Communication 8
Install the SmartGuard 600 Controller 9
Mount the SmartGuard 600 Controller 9
Grounding the SmartGuard 600 Controller 10
Connecting a Power Supply 11
Wiring the SmartGuard 600 Controller 12
Making Communication Connections 15
Interpreting the Status Indicators 17
Alphanumeric Status Display 18
Status Indicators 18
Specifications 24
Additional Resources 28
2 SmartGuard 600 Controllers
Publication 1752-IN001C-EN-P - January 2009
Important User Information
Solid state equipment has operational characteristics differing from those of electromechanical equipment.
Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (publication
SGI-1.1 available from your local Rockwell Automation sales office or online at
http://literature.rockwellautomation.com) describes some important differences between solid state
equipment and hard-wired electromechanical devices. Because of this difference, and also because of the
wide variety of uses for solid state equipment, all persons responsible for applying this equipment must
satisfy themselves that each intended application of this equipment is acceptable.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages
resulting from the use or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many
variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot
assume responsibility or liability for actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,
equipment, or software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell
Automation, Inc., is prohibited.
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
WARNING Identifies information about practices or circumstances that can cause an explosion in
a hazardous environment, which may lead to personal injury or death, property
damage, or economic loss.
IMPORTANT Identifies information that is critical for successful application and understanding of
the product.
ATTENTION Identifies information about practices or circumstances that can lead to personal injury
or death, property damage, or economic loss. Attentions help you identify a hazard,
avoid a hazard and recognize the consequences.
SHOCK HAZARD
Labels may be on or inside the equipment, for example, a drive or motor, to alert
people that dangerous voltage may be present.
BURN HAZARD
Labels may be on or inside the equipment, for example, a drive or motor, to alert
people that surfaces may reach dangerous temperatures.
SmartGuard 600 Controllers 3
Publication 1752-IN001C-EN-P - January 2009
North American Hazardous Location Approval
General Safety Information
The following information applies when operating
this equipment in hazardous locations.
Informations sur l’utilisation de cet équipement en
environnements dangereux.
Products marked "CL I, DIV 2, GP A, B, C, D" are suitable for use in
Class I Division 2 Groups A, B, C, D, Hazardous Locations and
nonhazardous locations only. Each product is supplied with
markings on the rating nameplate indicating the hazardous
location temperature code. When combining products within a
system, the most adverse temperature code (lowest "T" number)
may be used to help determine the overall temperature code of
the system. Combinations of equipment in your system are subject
to investigation by the local Authority Having Jurisdiction at the
time of installation.
Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne conviennent
qu'à une utilisation en environnements de Classe I Division 2
Groupes A, B, C, D dangereux et non dangereux. Chaque produit
est livré avec des marquages sur sa plaque d'identification qui
indiquent le code de température pour les environnements
dangereux. Lorsque plusieurs produits sont combinés dans un
système, le code de température le plus défavorable (code de
température le plus faible) peut être utilisé pour déterminer le
code de température global du système. Les combinaisons
d'équipements dans le système sont sujettes à inspection par les
autorités locales qualifiées au moment de l'installation.
WARNING EXPLOSION HAZARD -
• Do not disconnect equipment
unless power has been removed
or the area is known to be
nonhazardous.
• Do not disconnect connections to
this equipment unless power has
been removed or the area is
known to be nonhazardous.
Secure any external connections
that mate to this equipment by
using screws, sliding latches,
threaded connectors, or other
means provided with this product.
• Substitution of components may
impair suitability for Class I,
Division 2.
• If this product contains batteries,
they must only be changed in an
area known to be nonhazardous.
AVERTISSEMENT RISQUE D’EXPLOSION –
• Couper le courant ou s'assurer
que l'environnement est classé
non dangereux avant de
débrancher l'équipement.
• Couper le courant ou s'assurer
que l'environnement est classé
non dangereux avant de
débrancher les connecteurs. Fixer
tous les connecteurs externes
reliés à cet équipement à l'aide
de vis, loquets coulissants,
connecteurs filetés ou autres
moyens fournis avec ce produit.
• La substitution de composants
peut rendre cet équipement
inadapté à une utilisation en
environnement de Classe I,
Division 2.
• S'assurer que l'environnement est
classé non dangereux avant de
changer les piles.
ATTENTION Safety Programmable Electronic Systems (PES)
Personnel responsible for the application of safety-related programmable electronic
systems (PES) shall be aware of the safety requirements in the application of the system
and shall be trained in using the system.
4 SmartGuard 600 Controllers
Publication 1752-IN001C-EN-P - January 2009
ATTENTION Environment and Enclosure
This equipment is intended for use in Pollution Degree 2 Industrial environment, in
Overvoltage Category II applications (as defined in IEC publication 60664-1), at altitudes
up to 2000 m (6562 ft) without derating.
This equipment is considered Group 1, Class A industrial equipment according to
IEC/CISPR Publication 11. Without appropriate precautions, there may be potential
difficulties ensuring electromagnetic compatibility in other environments due to
conducted as well as radiated disturbance.
This equipment is supplied as open type equipment. It must be mounted within an
enclosure that is suitably designed for those specific environmental conditions that will
be present and appropriately designed to prevent personal injury resulting from
accessibility to live parts. The enclosure must have suitable flame-retardant properties to
prevent or minimize the spread of flame, complying with flame spread rating or 5VA, V2,
V1, V0 (or equivalent) if non-metallic. The interior of the enclosure must be accessible
only by the use of a tool. Subsequent sections of this publication may contain additional
information regarding specific enclosure type ratings that are required to comply with
certain product safety certifications.
In addition to this publication, see:
•Industrial Automation Wiring and Grounding Guidelines, Allen-Bradley publication
1770-4.1.
•NEMA Standards publication 250 and IEC publication 60529, as applicable, for
explanations of the degrees of protection provided by different types of enclosure.
ATTENTION Prevent Electrostatic Discharge
This equipment is sensitive to electrostatic discharge, which can cause internal damage
and affect normal operation. Follow these guidelines when you handle this equipment:
•Touch a grounded object to discharge potential static.
•Wear an approved wrist grounding strap.
•Do not touch connectors or pins on component boards.
•Do not touch circuit components inside the equipment.
•Use a static-safe workstation, if available.
•Store the equipment in appropriate static-safe packaging when not in use.
SmartGuard 600 Controllers 5
Publication 1752-IN001C-EN-P - January 2009
About the SmartGuard 600 Controller
SmartGuard 600 controllers, catalog numbers 1752-L24BBB and 1752-L24BBBE, are
programmable electronic systems featuring 16 digital inputs, 8 digital outputs, 4 test
pulse sources, and connections for USB and DeviceNet safety communication. In
addition, the 1752-L24BBBE controller offers EtherNet/IP connectivity.
SmartGuard 600 controllers are certified for use in safety applications up to and
including Safety Integrity Level (SIL) 3, according to IEC 61508,
Performance Level PL(e) according to ISO 13849-1, and Category (CAT) 4,
according to EN 954-1.
ATTENTION
T
Protective Debris Strip
Do not remove the protective debris strip until after the controller and all the other
equipment near the controller is mounted and wiring is complete.
Once wiring is complete, remove the protective debris strip. Failure to remove the strip
before operating can cause overheating.
ATTENTION Serious injury may occur due to the loss of required safety function.
•Do not use test outputs as safety outputs.
•Do not use DeviceNet standard I/O data or explicit message data as safety data.
•Do not use the safety indicators for safety operations.
•Do not connect loads beyond the rated value to safety outputs or test outputs.
•Wire the controller properly so that the 24V DC line does not accidentally touch the
outputs.
•Ground the 0V line of the power supply for external output devices so that the
devices do not turn on when the safety output line or test output line is grounded.
•Do not dismantle, repair, or modify the controller. Doing so may impair the safety
functions.
6 SmartGuard 600 Controllers
Publication 1752-IN001C-EN-P - January 2009
1752-L24BBB Controller
1752-L24BBBE Controller
Number Feature
1 Module status indicators
2 Alphanumeric display
3 Node address switches
4 Baud rate switches
5 USB port
6 DeviceNet communication
connector
7 Terminal connectors
8 Input status indicators
9 Output status indicators
10 Service switch
Number Feature
1 Module status indicators
2 Alphanumeric display
3 Node address switches
4 Baud rate switches
5 USB port
6 DeviceNet communication
connector
7 Terminal connectors
8 Input status indicators
9 Output status indicators
10 IP address display switch
11 Ethernet connector
12 Service switch
1
3
4
6
10
5
27
8
9
7
3
46
10
5
27
8
9
7
12
11
1
SmartGuard 600 Controllers 7
Publication 1752-IN001C-EN-P - January 2009
Before You Begin
Before you install the controller, set its DeviceNet node address and communication
rate.
Set the Node Address
Use a small screwdriver to set the DeviceNet node address by using the two rotary
switches on the front panel of the controller. Use care not to scratch the switches.
Values from 00…63 are valid. The default setting is 63.
Follow these steps to set the node address.
1. Set the tens digit of the node address (decimal) by turning the left rotary
switch.
2. Set the ones digit by turning the right rotary switch.
3. To set the node address by using RSNetWorx for DeviceNet software, set the
rotary switches to a value from 64…99.
Setting the Communication Rate
The default communication rate for a DeviceNet network is 125 Kbps.
If you choose to use a different communication rate, the length of the trunkline and
types of cable determine which communication rates your application can support.
IMPORTANT Turn off power to the controller before setting the node address or communication rate
via the switches.
Do not change the switch settings while the power supply is on. The controller will detect
this as a change in the configuration and will switch to the ABORT mode.
IMPORTANT A node address duplication error will occur if the same node address is set for more than
one node.
DeviceNet Communication Rates and Cable Lengths
Communication
Rate
Distance, Max Cumulative Drop
Line Length
Flat Cable Thick Cable Thin Cable
125 Kbps 420 m (1378 ft) 500 m (1640 ft) 100 m (328 ft) 156 m (512 ft)
250 Kbps 200 m (656 ft) 250 m (820 ft) 100 m (328 ft) 78 m (256 ft)
500 Kbps 75 m (246 ft) 100 m (328 ft) 100 m (328 ft) 39 m (128 ft)
8 SmartGuard 600 Controllers
Publication 1752-IN001C-EN-P - January 2009
Set the communication rate by using the DIP switch on the front of the controller.
Set the IP Address for Ethernet Communication
Connect the 1752-L24BBBE controller to the network via a 100 Mbps Ethernet
switch, which will help reduce collisions and lost packets, and increase bandwidth.
The 1752-L24BBBE controller is shipped with BOOTP enabled for setting the IP
address. You can use any commercially available BOOTP server. If you do not have
BOOTP Server capabilities on your network, download the free Rockwell
Automation BOOTP server from http://www.ab.com/networks/bootp.html.
To set the IP address by using the Rockwell Automation BOOTP utility, follow
these steps.
1. Run the BOOTP utility.
2. Double-click the hardware address of the device you want to configure.
DIP Switch Settings
DIP Switch
Pin
1 2 3 4 Communication Rate
OFF OFF OFF OFF 125 Kbps
ON OFF OFF OFF 250 Kbps
OFF ON OFF OFF 500 Kbps
ON ON OFF OFF Set by software
ON or OFF ON or OFF ON OFF Set by software
ON or OFF ON or OFF ON or OFF ON Automatic baud-rate detection
IMPORTANT If you change the communication rate of your network, make sure that all devices change
to the new communication rate. Mixed communication rates produce communication
errors.
SmartGuard 600 Controllers 9
Publication 1752-IN001C-EN-P - January 2009
3. In the the New Entry pop-up dialog box, type the IP address you want to
assign to the device, and click OK.
The controller appears in the Relation List.
For detailed information on EtherNet/IP communication, refer to the EtherNet/IP
Performance and Application Solution, publication ENET-AP001.
Install the SmartGuard 600 Controller
To install the SmartGuard 600 controller, you must mount it on the DIN rail, wire
the terminals, and make communication connections.
Mount the SmartGuard 600 Controller
IMPORTANT For effective cooling:
•mount the controller on a horizontal DIN rail. Do not mount the controller vertically.
•provide a gap of at least 50 mm (2.0 in.) above and below the controller and 5 mm
(0.20 in.) on each side.
•select a location where air flows freely or use an additional fan.
•do not mount the controller over a heating device.
10 SmartGuard 600 Controllers
Publication 1752-IN001C-EN-P - January 2009
Mount the controller only to a DIN rail. Follow these steps to mount the controller
to an EN 50022-35x7.5 or EN 50022-35x15 DIN rail.
1. Hook the top slot over the DIN rail.
2. Snap the bottom of the controller into position while pressing the controller
down against the top of the rail.
3. Attach end plates to each end of the DIN rail.
To remove the controller from the DIN rail, use a screwdriver to pull down the
latch and lift the controller off of the rail. The 1752-L24BBB controller has one latch
and the 1752-L24BBBE controller has two latches on the bottom of the controller.
Grounding the SmartGuard 600 Controller
You must provide an acceptable grounding path for each device in your
application. Functionally ground the controller through its V0/G0 power
connection.
In addition, if you are using the 1752-L24BBBE controller, you should connect the
Ethernet ground terminal to an acceptable ground.
ATTENTION This product is grounded through the DIN rail to chassis ground. Use zinc plated
yellow-chromate steel DIN rail to assure proper grounding. The use of other DIN rail
materials (for example, aluminum or plastic) that can corrode, oxidize, or are poor
conductors, can result in improper or intermittent grounding. Secure DIN rail to mounting
surface approximately every 200 mm (7.8 in.) and use end anchors appropriately.
Latch
Top Slot
DIN Rail
Otros manuales para SmartGuard 600
2
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Controladores de Rockwell Automation
Rockwell Automation
Rockwell Automation MagneMotion 700-0871-00 Manual de usuario
Rockwell Automation
Rockwell Automation 9VT201-007HTNNN Manual de usuario
Rockwell Automation
Rockwell Automation Allen-Bradley 150-E Manual de usuario
Rockwell Automation
Rockwell Automation Allen-Bradley Micro820 Manual de usuario
Rockwell Automation
Rockwell Automation Allen-Bradley ARMORSTART Manual de usuario
Rockwell Automation
Rockwell Automation ics triplex AADvance Manual
Rockwell Automation
Rockwell Automation Allen-Bradley Logix 5000 Series Manual del propietario
Rockwell Automation
Rockwell Automation 1756-L1 Manual de usuario
Rockwell Automation
Rockwell Automation PowerFlex 753 Manual de usuario
Rockwell Automation
Rockwell Automation Allen-Bradley DriveLogix 5730 Manual de usuario
Rockwell Automation
Rockwell Automation Allen-Bradley Logix5000 Manual del propietario
Rockwell Automation
Rockwell Automation PowerFlex 755 Guía rápida
Rockwell Automation
Rockwell Automation Micro830 Manual de usuario
Rockwell Automation
Rockwell Automation SMC FLEX Manual de usuario
Rockwell Automation
Rockwell Automation PowerFlex 700S Manual de usuario
Rockwell Automation
Rockwell Automation Allen-Bradley CompactLogix 5370 L2 Series Manual de usuario
Rockwell Automation
Rockwell Automation PowerFlex 700S Manual de usuario
Rockwell Automation
Rockwell Automation Allen-Bradley SMC-50 Manual de usuario
Rockwell Automation
Rockwell Automation PowerFlex 700S Manual de usuario
Rockwell Automation
Rockwell Automation Allen-Bradley Logix 5000 Series Manual del propietario
Rockwell Automation
Rockwell Automation Allen-Bradley GuardLogix Guía del usuario
Rockwell Automation
Rockwell Automation Allen-Bradley Logix 5000 Series Manual del propietario
Rockwell Automation
Rockwell Automation Allen-Bradley PowerFlex 70 Manual de usuario
Rockwell Automation
Rockwell Automation GV3000/SE 230 Manual de instalación y operación
