Risco EL-5829 Manual de usuario
2-Way Wireless
LCD Keypad
Model: EL-5829
Installation and User Guide
2
Language
Page
3
14
26
38
50
3
1. Description
The EL-5829 is a 2-Way wireless keypad with LCD display used to remotely
program and operate the iConnect 2-Way systems.
The keypad's functionality is identical to the keys on the iConnect 2-Way front panel.
Note: Programming mode can be established either from a keypad or from the
main panel, but not simultaneously.
What’s in the Box
•2-Way LCD wireless keypad
•4 x CR123 Lithium batteries
•5 wooden screws 3.5 x 25 mm
•Installation Instructions
2. Installation
Registration
The EL-5829 keypad must identify itself to the system receiver. This is done by
registering the keypad to the iConnect 2-Way, as follows.
1. Set the system to Registration mode.
a. Go to the main menu and select [9]>[1]>[3]
(Programming > Devices > Keypads).
b. Select a keypad (1 - 4).
2. Release the mounting bracket.
3. Open the battery compartment and insert the batteries. Pay attention to the
correct polarity.
4. As soon as 'Save?' appears on the Control System’s LCD screen, press '√'.
4
Deleting a Keypad
➢To delete a wireless keypad from the system:
1. Set the system to Delete mode.
a. Go to the main menu and select [9]>[1]>[3]
(Programming > Devices > Keypads).
b. Select a keypad (1 - 4).
c. Select the Delete menu.
d. Press > .
2. Take out the keypad batteries.
3. Insert the batteries.
4. Within a 30-second time period, press and simultaneously for
three seconds; the keypad will display the software version and
'Not Registered'.
Wall Mounting
After the keypad has been registered to the system mount the keypad on the wall
using the supplied mounting bracket.
Notes:
1. Before mounting the keypad test the keypad communication with the system.
To do so, try to arm the system using one of the arming buttons on the wireless
keypad (see Figure 1).
2. Minimum mounting distance between the wireless keypad and the panel is
1.5m.
5
➢To mount the keypad:
1. Release the mounting bracket.
2. Attach the mounting bracket to the wall using the supplied screws (see
figure 1).
Figure 1
3. Attach the wireless keypad to the mounting bracket by sliding the keypad
down onto the bracket‘s four hooks (see figure 2).
Mounting
Mounting
Mounting hole for tamper
Mounting Mounting
6
Figure 2
4. Attach the housing screw at the bottom of the front cover (see figure 3).
Figure 3
Note:To use the back tamper, the back-tamper screw must be installed.
7
3. Main User Operations
Control Keys
Key
Operation
In Normal Operation mode: Used for Away (Full setting).
In Normal Operationmode: Used for Stay arming (Part Setting).
In Normal Operation mode: used to enter the menus with code.
Long press: activates quick registration
Used also to terminate commands and confirm data to be stored.
In Normal Operation mode: Used for Perimeter arming.
Provides the system status.
Used to scroll up a list or to move the cursor to the left;
Used to scroll down a list or to move the cursor to the right.
To view system trouble list
In User Functions menu: used to move back one step in the menu.
Long press: activates quick delete mode
8
Emergency Keys
The following operations will send emergency notifications to the alarm monitoring
station.
Key
Operation
+
Pressing both keys simultaneously for at least two
seconds activates a Fire alarm
+
Pressing both keys simultaneously for at least two
seconds activates an Emergency alarm
+
Pressing both keys simultaneously for at least two
seconds activates a Police (Panic) alarm.
Used for tele-control.
In User Functions menu, used to change data:
•To enter space, press left key
•To delete data, press right key
Long press of right key to activate Battery Replace mode
Function Keys
Key
Operation
Numerical keys that are used to input numeric codes
(arming, disarming or used to activate specific
functions).
9
4. Visual Indicators
The following visual indicators are displayed on the LCD panel:
Icon
Indication
Operation
Power
On
System is operating properly from AC
power and backup battery is in good
condition
Slow flash
Control Panel/Keypad low battery
Rapid flash
Control Panel AC loss
Trouble / Tamper
On
System trouble
Off
System is operating normally
Rapid flash
Zone/keypad/external module has been
tampered
Ready
On
System is ready to be Set
Off
System is not ready to be Set/Arm
Set / Alarm
On
System is set in Full Set, Part Set or
Perimeter Set mode
Off
System is Unset
Rapid Flash
Alarm condition
10
5. Replacing Batteries
When the batteries need to be replaced the indicator will flash.
➢To replace the batteries:
1. From the control panel, long press to enter replace battery mode.
2. Remove the keypad from the wall.
3. Open the battery compartment (see Figure 4).
Figure 4
4. Pull out the batteries and replace them with new ones. Pay attention to the
polarity when inserting the new batteries (see Figure 5)
Tabla de contenidos
Idiomas:
Otros manuales de Teclado de Risco
Risco
Risco Agility RW132KL1P Manual de usuario
Risco
Risco Panda RW332KP Manual de usuario
Risco
Risco Panda RW332K Manual de usuario
Risco
Risco WL Panda Manual de usuario
Risco
Risco RW132KL1 Manual de usuario
Risco
Risco RPKELW Manual de usuario
Risco
Risco Agility 132KP Manual de usuario
Risco
Risco RPKEL Manual de usuario
Risco
Risco GARDTEC 872 Manual de usuario
Risco
Risco Agility 2-way Wireless LCD Keypad Manual de usuario
Risco
Risco lightsys RP432KPP Manual de usuario
Risco
Risco Agility RW132KL1P Manual de usuario
Risco
Risco lightsys RP432KP Manual de usuario
Risco
Risco lightsys RP432KP Manual de usuario
Risco
Risco RW132KPPW3 Manual de usuario
Risco
Risco RPKELP Manual de usuario
Risco
Risco RPKELW Manual de usuario
Risco
Risco lightsys 2 Manual de instrucciones
Risco
Risco RP432KPP2 Manual de usuario
Risco
Risco lightsys RP432KP Manual de usuario
