RIOTEC DC9250DP Manual de usuario

1

Quick Guide

-DC9250DP

1 H92P

Connect to micro USB port of OTG device

3



* Before you use scanner, please switch to "C" for battery charge

for 3~4 hours.

* Under “C mode”, you can raise/lower soft-keyboard easily.(For

USB HID only)



H92P Scan Holder is with Li-Ion battery inside. When in charging,

please use the original USB power adaptor of OTG device

(recommended). Through it, it charges both OTG device and H92P

internal battery at the same time. When in low battery (Red LED

flashing), please charge it immediately.

LED Indicator Information

Green LED OFF Full charged (Charge mode)

Green LED ON Charging (Charge mode)

Red LED Flashing Low battery (Operation mode)

Attention: Under “Operation mode” please do not charging,

otherwise the OTG device's battery will be charging back to H92P’s

battery.

5



The touch sensor area is around the central area. (For both sides).

Please check the above drawing for your reference.

Installation

Before using scanner, please make sure that the OTG device is fully

charged.

1. Under USB HID interface

** When plugged into OTG device, it will be recognized and begin

to scan the barcode.

2. Under USB Serial interface

** Please install PL-2303 driver into your OTG device first. PL-2303

driver can be downloaded from Google Play

** Connect scanner to your OTG device, then, you can know which

serial port scanner connects to.

** The data you scan will be sent to serial port and your APP can

get the data from serial port directly.

Suction Cup

Micro USB

cable (OTG)

Li- Ion

Battery

Trigger Area

O = Operation mode

Charge mode

LED Indicator

Char

e por

H92P

Mini

scanner

PU Glue

(Can be used

repeatedly)

2

Reset Configuration to Defaults

If you are unsure of the scanner configuration or have scanned the

incorrect codes, please scan the “Default” barcode. This will reset the

scanner to its factory default. (scan from A1 to A6 for HID or B1 for

USB Serial)

USB HID USB Serial

 Note: Please install PL-2303 driver for USB Serial.

Keyboard Country(For USB HID only)

Scan the appropriate country code as below to program the

keyboard layout for your country or language. As a general

rule, the following characters are supported, but need special

care for countries other than the United States:

@ | $ # { } [ ] = / ‘ \ < > ~

USA

(Original setting)

Italian

Norway

France

Germany

Vietnam

Sweden

Spain

Denmark

ortu

Switzerland Hun

ary

Barcode Configuration Method:

Please follow the below 4 steps to complete the

"Symbologies Enable" or "Symbologies Disable"

1. Start Configuration

2. Choose one of 1D symbologies

3. Enable setting: scan Enable-1, then Enable-2

Disable setting: scan Disable-1, then Disable-2

4. End Configuration

Start

Configuration

1D Symbologies – 1

UPC-A UPC-E

EAN-13

(ISBN/ISSN)

EAN-8

Industrial

2 of 5

Matrix

2 of 5

Enable-1 Disable-1

Enable-2 Disable-2

End

Configuration

3

Barcode Configuration Method:

Please follow the below 4 steps to complete the

"Symbologies Enable" or "Symbologies Disable"

1. Start Configuration

2. Choose one of 1D symbologies

3. Enable setting: scan Enable-1, then Enable-2

Disable setting: scan Disable-1, then Disable-2

4. End Configuration

Start

Configuration

1D Symbologies – 2

Code 93

Code 11

MSI/Plessey

UK/Plessey

Codabar

Code 128

UCC/EAN 128

ISBT 128

1D Symbologies – 3

Code 39

(Code 32)

Interleaved

2 of 5

China Post GS1 DataBar

GS1 DataBar

Limited

GS1 DataBar

Expanded

Enable-1 Disable-1

Enable-2 Disable-2

End

Configuration

 Information in this document is subject to change without notice.

 For more information, please visit:

www.riotec.com.tw

R_180504_01

Otros manuales de Lector de código de barras de RIOTEC

RIOTEC

RIOTEC LS6300J Manual de usuario

RIOTEC

RIOTEC iLS6302NBU Manual de usuario

RIOTEC

RIOTEC RIOSCAN iLS6308KS Manual de usuario

RIOTEC

RIOTEC DC9257AN Manual de usuario

RIOTEC

RIOTEC iDC9607AW Manual de usuario

RIOTEC

RIOTEC DC9270D Manual de usuario

RIOTEC

RIOTEC iLS6302J/KBU Manual de usuario

RIOTEC

RIOTEC iDC9607L Manual de usuario

RIOTEC

RIOTEC iDC9270J Manual de usuario

RIOTEC

RIOTEC LS6308K Manual de usuario

RIOTEC

RIOTEC RIOSCAN iCR6307AS Manual de usuario

RIOTEC

RIOTEC FS5107A Manual de usuario

RIOTEC

RIOTEC iLS6300JB Manual de usuario

RIOTEC

RIOTEC LS6300 Manual de usuario

RIOTEC

RIOTEC OM7228J Manual de usuario

RIOTEC

RIOTEC RIOSCAN iLS6302JS Manual de usuario

RIOTEC

RIOTEC iDC9507L Manual de usuario

RIOTEC

RIOTEC iCR6300CBQ Manual de usuario

RIOTEC

RIOTEC iDC9508K Manual de usuario

RIOTEC

RIOTEC LS6300E Manual de usuario

RIOTEC

RIOTEC iLS6307LB Manual de usuario

RIOTEC

RIOTEC iDC9608KW Manual de usuario

RIOTEC

RIOTEC FS5108J Manual de usuario

RIOTEC

RIOTEC RIOSCAN iLS6300JS Manual de usuario

Manuales populares de Lector de código de barras de otras marcas

POSMicro

POSMicro Datalogic PowerScan D7100 Manual de usuario

Marson

Marson MT780 Guía de configuración rápida

NCR

NCR RealPOS Manual de usuario

Motorola

Motorola SE3300 Guía de configuración rápida

Element

Element P130BT Manual de usuario

Motorola

Motorola Symbol LS3008 Manual de instalación y operación

Meec tools

Meec tools OBD-II / VAG Manual de usuario

SICK

SICK CLP 100 Manual de usuario

Royal Tag SA

Royal Tag SA I-Read Manual de usuario

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manual de usuario

Meteor

Meteor 8310 Manual de usuario

Denso

Denso BHT-500B Manual de usuario

Datalogic

Datalogic Heron HD3130 Manual de usuario

Motorola

Motorola MP6000 Instrucciones de montaje

Newland

Newland NLS-HR15-BT Manual de usuario

ARTDEV

ARTDEV AS-1310 Manual de usuario

Aopos

Aopos AS290 Manual de usuario

ENS

ENS 367-5455 Manual de usuario