Rinnai RS100 Guía de solución de problemas

Condensing Boiler

RS100 Controller Training Program

Training Program #501102A –

062311

Features and Benefits

•Direct communication with the boiler allows it to fire based on the area’s immediate needs

•Operation is controlled by simple rotary push button technology

•Digital display (with backlight):

•Fahrenheit or Celsius

•Ability to display outdoor temperature

•Ability to display supply temperature

•Ability to display system pressure

•Indication of operating capacity (% of Btu)

•Error and warning reporting

•Multiple programming options

•Vacation program

•Three event programs per day

•Three weekly programs

•Summer setback economy mode

•Anti-Legionella programming available for domestic hot water

•Two-wire connection—no battery needed for power

•Integrated battery for memory saves settings during power outage

•Battery will last five years in off mode—it is not used when powered

RS100 –Programmable Wall Thermostat with room setback

•The RS100 connects directly to the boiler and acts as a central thermostat for the entire structure

Applications for the RS100 Room controller

The RS100 is a room controller and not an on/off room thermostat. It is intended to work only

with Rinnai boilers. When used in conjunction with a Rinnai boiler it will sense the room

temperature and use it to influence the supply water temperature. This will allow less cycling of

the boiler and a more efficient installation. The RS100 is designed to control a single circuit of

heating.

There are two basic applications for the RS100:

•In single zone systems, as a remote boiler display with influence from the room or area where the controller

is installed

•This can be done with only room influence and no outdoor reset influence

•Since the RS100 is constantly reporting room conditions to the boiler, the boiler can still modulate

effectively—constant outdoor temperature reporting is not needed for normal operation (it is still beneficial

for freeze protection)

•The RS100 should be installed in the coldest room

•In multiple zone systems, as a remote boiler display only with no room influence from the controller

•This can be done with or without the room temperature displayed

•This would be considered a 100% outdoor reset boiler where the pump runs continuously and the load is

based solely on the outside temperature

•The RS100 can be installed in any room in this application

Scope of Use

Scope of Use-

Single Zone System (RC mode)

The RS100 can be used to

control a single heating zone

system. A single heating zone

system has only one loop of

heating. The placement of

the RS100 is very important;

it must be placed in the

coldest room within the single

zone system. If the RS100 is

not placed in the coldest room

there is a chance that the

room will not receive enough

heat and therefore not be

comfortable. The RS100

needs no additional installer

level programming to work for

this installation.

Scope of Use-

Multiple Zone System (Outdoor Reset mode)

Zone

Thermostats

Third

Party

Controller

Outdoor

Sensor Zone Valve Piping

In this application, the RS100 will allow

the boiler to switch between day and

night outdoor reset curves. The boiler is

then operating with constant circulation

and no input from room thermostats

(on/off) or third party controls. In this

application, a third party relay panel

should be used to control pumps or

zone valves. The panel cannot be

connected to the boiler with an RS100

also connected. Boiler thermostat

terminals 22 and 23 are inactive when

the RS100 is connected.

If multiple zones are used, it is

likely not beneficial to have a

single zone controlling the

boiler’s demand. The RS100

can be used where its room

information does not influence

the boiler’s demand. Its clock

functions are still active as

well as the ability to adjust a

theoretical temperature for

comfort.

Zone

Thermostats

Third

Party

Controller

Outdoor

Sensor Zone Pump Piping

The boiler in this application is

operating with constant

circulation and no input from

room thermostats (on/off) or third

party controls. The third party

control panel cannot be

connected to the boiler with an

RS100 also connected. Boiler

thermostat terminals 22 and 23

are inactive when the RS100 is

connected.

Scope of Use-

Multiple Zone System (Outdoor Reset mode)

INSTALLATION

BASICS

THIS IS AN OVERVIEW ONLY—PLEASE REFER TO EACH BOILER OR CONTROLLER

INSTALLATION MANUAL THAT IS SHIPPED WITH THE PRODUCT FOR THE MOST UP TO DATE

INFORMATION. CONTACT RINNAI TECHNICAL SUPPORT IF NEEDED

Electrical Connections

Below is the connection for the RS100. Please refer to the installation manual and Rinnai’s recommended

application guide for more details or contact Rinnai’s Engineering Department as needed

The RS100 will connect to terminals 20 and 21

•Controller wire should be no longer than 164 ft

•Controller wire should be 18 (AWG) Gauge

•Controller wire should be shielded if near high

voltage (120 V or higher) or if a long distance-the

ground should be connected at the boiler (not at

the controller)

•Mount the controller in the coldest area of the

structure

•Do not mount in direct sun

•Do not mount too close to a heat emitter (where

the emitter could falsely influence the controller)

•Do not mount near lighting that could falsely

influence the controller

Outdoor reset sensor (included with boiler)

connects here. When power is first applied

to the boiler, if the outdoor reset sensor is

not connected, the boiler will not incorporate

any outdoor temperature monitoring

On/Off room

thermostat or

control (no

voltage, dry

contact),

jumping these

points will

cause the

boiler to fire if

there is no

RS100

connected. If

an RS100 is

connected at

terminals 20

and 21, the

boiler will

ignore these

terminals.

Connect the wires to

the back panel of the

controller. Ensure

wire ―A‖ from the

controller is

connected to

terminal 20 (wire

―A‖) on the Boiler.

Ensure wire ―B‖ is

connected to 21.

Release the tab at

the bottom of the

controller to

access the

connection points

Note: If these are swapped the RS100 will

not exit ―Auto Set‖ upon booting.

BASIC

OPERATION

THIS IS AN OVERVIEW ONLY—PLEASE REFER TO EACH BOILER OR CONTROLLER

INSTALLATION MANUAL THAT IS SHIPPED WITH THE PRODUCT FOR THE MOST UP TO DATE

INFORMATION. CONTACT RINNAI TECHNICAL SUPPORT IF NEEDED

RS100 Power-on Initialization

The following sequence will occur every time power is reset or the “reset” button on the boiler is pressed

This process takes about 30 seconds

RS100 –Display during initialization

A display test

will occur where

all characters

are illuminated

The selected language will

display.

“GB” = English

If factory defaults are restored to

the controller, this should be

changed to ―GB‖

Pressing the dial will exit the

language display quicker

The current

software version

will display

(Version 2.3 is

current as of

10/09)

Auto set will display for

a few seconds. NOTE:

If the A and B wires are

reversed from the

controller to the boiler,

the controller will not

exit this page

Otros manuales para RS100

Tabla de contenidos

Otros manuales de Controladores de Rinnai

Rinnai

Rinnai Infinity V26 series Manual de servicio

Rinnai

Rinnai BC-100V1Z Guía de inicio rápido

Rinnai

Rinnai BRIVIS Touch Manual de usuario

Rinnai

Rinnai MC-100V Manual de usuario

Rinnai

Rinnai CNTRLDRCIZHAW Guía rápida

Rinnai

Rinnai Demand Duo Manual de usuario

Rinnai

Rinnai MC-100V Hoja de especificaciones

Rinnai

Rinnai MC-601 Instrucciones de instalación

Rinnai

Rinnai Demand Duo Instrucciones de funcionamiento

Rinnai

Rinnai MC-601-W Manual de usuario

Rinnai

Rinnai MC-601Q Manual de usuario

Rinnai

Rinnai MC502S Manual de usuario

Rinnai

Rinnai MC-601 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario