Rice Lake Versa-portion RLP-S Manual de usuario

Versa-portion RLP-S/SM

Multi-Purpose Bench Scale

Operation Manual

115519

Contents

About This Manual ......................................................................................1

Introduction .................................................................................................1

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Operation .....................................................................................................2

On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Tare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Automatic Shut-Off Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Display Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Default Primary Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

G, lb and oz Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Calibration ..................................................................................................3

Software Version and Span State Check . . . . . . . . . . . . . . . . . . . . . . . . . 3

Performing a Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Enclosure Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Setting the SPEC Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Internal Count and A/D Count Display . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Appendix .....................................................................................................7

DC Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Battery Pack Replacement/Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Battery Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Specifications .............................................................................................9

Versa-portion RLP-S/SM Limited Warranty ..............................................10

Specifications subject to change without notice.

Rice Lake Weighing Systems is an ISO 9001 registered company.

Version 2 12/2011

Introduction 1

1.0 Introduction

bThe Versa-portion RLP-S/SM is a multi-purpose bench scale that offers practical

solutions for a full range of applications. Its internal resolution of 1/90,000 gives

you maximum precision and accuracy. Its backlit LCD display enables operators

to easily see weights. When portability is required, choose the optional

rechargeable battery for over 60 hours of continuous usage. The Versa-portion

RLP-S/SM is designed to reliably operate in many environments and withstand

transport from one area of the plant to another or from one business to the next.

This manual can be viewed or downloaded from the RLWS website at

www.ricelake.com/manuals.

1.1 Safety

Safety Signal Definitions:

WARNING

Important

CAUTION

WARNING

Indicates a potentially hazardous situation that, if not avoided could result in

serious injury or death, and includes hazards that are exposed when guards

are removed.

Indicates a potentially hazardous situation that, if not avoided may result in

minor or moderate injury.

Indicates information about procedures that, if not observed, could result in

damage to equipment or corruption to and loss of data.

General Safety

Do not operate or work on this equipment unless you have read and

understand instructions in the manual. Failure to follow the instructions or

heed the warnings could result in injury or death. Contact any Rice Lake

Weighing Systems dealer for replacement manuals. Proper care is your

responsibility.

Failure to heed may result in serious injury or death.

DO NOT allow minors (children) or inexperienced persons to operate this unit.

DO NOT operate without all shields and guards in place.

DO NOT jump on the scale.

DO NOT use for purposes other then weight taking.

DO NOT place fingers into slots or possible pinch points.

DO NOT use any load bearing component that is worn beyond 5% of the original dimension.

DO NOT use this product if any of the components are cracked.

DO NOT exceed the rated load limit of the unit.

DO NOT make alterations or modifications to the unit.

DO NOT remove or obscure warning labels.

Keep hands, feet and loose clothing away from moving parts.

2Versa-portion RLP-S/SM Operation Manual

1.2 Front Panel

Table 1-1 lists the indications and front-panel buttons available on the Versa-

portion RLP-S/SM.

Table 1-1. Versa-portion RLP-S/SM Indications and Front-Panel Buttons

Indication Description

On when the weight display is in ounces

*(not available in Versa-portion RLP-SM)

On when the weight display is in pounds

*(not available in Versa-portion RLP-SM)

(kg)

On when the weight display is in grams

*(Versa-portion RLP-SM value is kg, display is in kilograms)

On when the zero point is adjusted and the weight is stable

On when tare subtraction is performed

On (blinking) when the battery is weak and needs to be recharged

Front-Panel Button Description

Resets the weight display to zero

Sets or clears the tare value

Turns the display on/off

Changes measurement units between lb, oz, g, kg

(not available in Versa-portion RLP-SM)

2Versa-portion RLP-S/SM Operation Manual

2.0 Operation

2.1 On/Off

1.Press the POWER key. The display will blink 8.8.8.8.8.8. and show 0.000 when ready

to weigh.

2.2 Tare

Tare values can be used for up to half of scale capacity.

Performing a Tare

1.Place the item to be tared (typically a container) on the platter.

2.Press the TARE key.

3.The display will show 0.000 with the tared item on the platter.

Removing a Stored Tare

1.Remove the tared item from the platter.

2.Press the TARE key.

3.The display will show 0.000.

2.3 Automatic Shut-Off Timer

The Versa-portion RLP-S/SM has a built-in automatic shut-off timer. This timer can be set

to turn the unit off after three minutes of inactivity or 10 minutes of inactivity.

Setting the Timer for Three Minutes

1.If the unit is powered on, press the POWER key until it shuts down.

2.With the unit powered off, press and hold the POWER key for three seconds.

The display will show 3.

3.Release the POWER key. The timer is now set to turn the unit off after three minutes of

inactivity.

Setting the Timer for 10 Minutes

1.If the unit is powered on, press the POWER key until it powers off.

2.With the unit powered off, press and hold the POWER key for six seconds.

The display will show 3after a period of three seconds. It will show 10 after six

seconds.

3.Once the display shows 10, release the POWER key. The timer is now set to turn the

unit off after 10 minutes of inactivity.

Disabling the Timer

1.If the unit is powered on, press the POWER key until it shuts down.

2.With the unit powered off, press and hold the POWER key for nine seconds.

The display will show 3after a period of three seconds and 6after six seconds. It will

show 999 after nine seconds.

3.Once the display shows 999, release the POWER key. The timer is now disabled.

2.4 Display Brightness

The Versa-portion RLP-S/SM display brightness can be set to one of three levels.

Changing the brightness setting

1.Hold the ZERO key and press Ta r e three times.

2.Press the ZERO key to increase the dimmer level and the Power button to decrease the

dimmer level.

3.The display will show 1, 2, 3, or 4depending on which dimmer level is being

displayed.

4.Press the TARE key to save the setting and return to weigh mode.

Operation 3

2.5 Default Primary Unit

The Units button cycles through g, lb, and oz. (Versa-portion RPL-SM is only available in

kg)

Setting the Default Primary Unit

1.Hold the ZERO key and press the UNITS key three times.

2.Press the POWER key to cycle through available units.

3.When the desired default unit is displayed, press the TARE key to save the setting and

return to weigh mode.

2.6 G, lb and oz Conversion

(Not available in Versa-portion RLP-SM)

G, lb and oz conversion is available only when SPEC08=011 (see Section 3.4).

1.Switch between units by pressing the UNITS key.

Note

(G) uppercase is the abbreviation for gross.

(g) lowercase is the correct abbreviation for grams.

Calibration 3

3.0 Calibration

To enter calibration mode, remove the screw on the bottom of the scale as shown

in Figure 3-1. Use a small tool to press the span setup switch located under the

screw. Setup will time out to verify the switch is set to the ON position. Then,

perform a span switch state check (see Section 3.1).

Remove Screw

Figure 3-1. Setup Switch

3.1 Software Version and Span State Check

1.With the unit in weigh mode, press and hold the ZERO key.

2.With the ZERO key held, press and release the POWER key three times.

3.The display will show the software version for two seconds, then show the

current span switch state (S-ON or S-OFF).

After three seconds, the unit will return to weigh mode.

3.2 Performing a Calibration

The Versa-portion RLP-S/SM must be calibrated in grams or kilograms, and

SPEC 01 and 02 must be set for the gram value (or kg in the SM version). See

Section 3.4.

1.With the unit in weigh mode, press and hold the ZERO key.

2.With the ZERO key held, press and release the POWER key twice, then press

and release the TARE key.

The display will show CAL00.

Note

4Versa-portion RLP-S/SM Operation Manual

To exit calibration at any time, press the TARE key.

3.Ensure there is no weight on the platter, then press the ZERO key to

calibrate the zero point.

The display will show dashes, then CALSP.

4.Place the scale’s full capacity weight on the platter and press the ZERO key to

calibrate span.

The display will show dashes, then the weight value.

Calibration weight is full grams capacity. Full capacity values are as

follows: RLP-6S = 3000 g (3 kg);



RLP-15S = 6000 g (6 kg); RLP-30S = 15000 g (15 kg); RLP-60S = 30000 g

(30 kg).

5.The scale will return to weigh mode automatically. Power down the unit.

6.Calibration is complete.

3.3 Enclosure Security

After an NTEP inspector has examined the unit, he/she will install security cables

through three bolts on the underside of the scale. These cables prevent the unit

from being tampered with by an unauthorized individual. If the cable is removed,

NTEP certification will become void.

Figure 3-2. Legal for trade seal; cable passes through three bolts

3.4 Setting the SPEC Value

The SPEC value is used to specify decimal point position, minimum display, net/

gross multi-interval, resolution, weight single or multi-interval, decimal point

figure, negative weight display mask, IR mode protection (SPAN switch must be

turned on to allow calibration), start range (amount of weight that can be on the

scale when it is turned on), re-zero range, manual tare cancellation, tare

subtraction, tare accumulation, auto tare, weight reset, tare auto clear, zero

tracking, re-zero, and the UNIT key function. See Table 3-1 on page 5.

1.Press the setup switch (see Figure 3-1).

2.With the unit in weigh mode, press and hold the ZERO key.

Otros manuales para Versa-portion RLP-S

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Escala de Rice Lake

Rice Lake

Rice Lake QB Series Manual de usuario

Rice Lake

Rice Lake RoughDeck FXB Manual de usuario

Rice Lake

Rice Lake Retail Series Manual de uso y cuidado

Rice Lake

Rice Lake Ishida Uni-7 Series Guía del usuario

Rice Lake

Rice Lake Survivor SR Manual de usuario

Rice Lake

Rice Lake Load Ranger Manual de usuario

Rice Lake

Rice Lake CLS Series Manual de usuario

Rice Lake

Rice Lake Summit SB-1000 Manual de usuario

Rice Lake

Rice Lake DIGI DSX-1000 Manual de usuario

Rice Lake

Rice Lake equipoise Manual de usuario

Rice Lake

Rice Lake 250-10-4 Series Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

Rice Lake

Rice Lake RL101 Manual de usuario

Rice Lake

Rice Lake RL-DBS-2 Manual de usuario

Rice Lake

Rice Lake 250-10-4 Series Manual de usuario

Rice Lake

Rice Lake RL150-10-7 Manual de usuario

Rice Lake

Rice Lake TS Series Manual de usuario

Rice Lake

Rice Lake Competitor Series Manual de usuario

Rice Lake

Rice Lake RL-MIS Manual de usuario

Rice Lake

Rice Lake equipoise Manual de usuario

Rice Lake

Rice Lake SURVIVOR CW-80 Manual de usuario

Rice Lake

Rice Lake BenchMark Series Manual

Rice Lake

Rice Lake SURVIVOR RL1700 HE Manual de usuario

Rice Lake

Rice Lake BCi Manual de usuario

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario

Fidelity Electronics

Fidelity Electronics G2e Manual de usuario