Rice Lake CLS Series Manual de usuario
Cargo Lift Scale Series
Wired to Wireless Conversion Instructions
Manuals can be viewed or downloaded from the Rice Lake Weighing Systems website at www.ricelake.com/manuals
The CLS Series Cargo Lift Scale has the capability to go from wired to wireless operation with a few steps. The wireless option
attaches onto the back of the indicator and collects data from the junction box without the use of a coiled wire cable.
The conversion kit contains the following items:
• Angle/battery box assembly (PN 167282)
• Wireless sub-assembly box (PN 98289)
• Lithium-Ion battery (PN 96343)
• Lithium-Ion battery charger (PN 96344)
Wireless communication between the indicator and the junction box which is located on the forklift and is powered by a
lithium-ion battery housed in a battery box.
Figure 1. Wireless Components for Communication
To convert the unit from wired to wireless:
1. Remove the angle bracket and the wired cable connecting the indicator to the forklift scale.
2. Install and wire from the wireless sub-assembly box to the indicator.
3. Install the angle/battery box assembly to the top of the carriage.
Remove Wired Cable
To remove the wired cable from the forklift to the indicator:
1. Cut cable ties that are securing the coiled wire between the bottom of the scale and the top of the mast of the forklift.
2. Disconnect the cable from the indicator.
3. Remove top cover plate from the forklift to access the junction box located beneath.
4. Disconnect the wired cabling from the junction box.
PN 101112 Rev B
May 14, 2019
CLS Series Wired to Wireless Conversion Instructions
2 Visit our website www.RiceLake.com
Install and Wire the Wireless Sub-Assembly Box to Indicator
To install the wireless sub-assembly box to the indicator:
1. Use the attached screws and screw the wireless sub-assembly box onto the back of the indicator.
2. Open the rear of the indicator.
3. Run the wire through bottom cord grip of indicator and wire into the connections.
Figure 2. Indicator
Attach the wireless
sub-assembly on to the
rear of the indicator.
CLS Series Wired to Wireless Conversion Instructions
© Rice Lake Weighing Systems ● All Rights Reserved 3
CLS-420 Wiring Diagrams
Figure 3. CLS-420 Indicator Wiring Diagram
Red
Black
Blue
White
Green
CLS Series Wired to Wireless Conversion Instructions
4 Visit our website www.RiceLake.com
Installing the Angle Cover Plate and Battery Box Assembly
To install the angle cover plate and battery box assembly:
1. Attach pigtail from angle cover plate and battery box assembly to junction box.
2. Secure angle cover plate and battery box assembly to top of carriage.
3. Install battery.
4. Following for battery option.
Figure 4. Battery Box
Wireless Battery Option
Wireless technology eliminates the need for the coiled interface cable. The reinforced battery box is welded onto the cover
plate. There is an On/Off switch to conserve the life of the battery and an LED to indicate when the battery is on. Battery life is
approximately 24 hours of continuous use, with only eight hours to fully charge.
The wireless technology operates using a paired set of IEEE 802.15.4 wireless modules. It operates in unlicensed bands
including 2.4 GHz, 900MHz and 868 MHz. One module is in the battery angle bracket assembly, the other is in the wireless
junction box connected to the indicator.
If multiple units are being installed, make a note of the original components supplied on each pallet. They will only operate in
combination with each other.
Figure 5. Wireless Battery Option
LED indicates On/Off
Antenna
On/Off Switch
CLS Series Wired to Wireless Conversion Instructions
© Rice Lake Weighing Systems ● All Rights Reserved 5
Battery Removal and Installation
To replace the lithium-ion battery that powers the unit:
1. Place the On/Off switch in the Off position.
2. Release latches and raise the cover.
3. Grasp a tab on the end of the battery and pull up.
4. Insert a new/charged battery into the battery case.
5. Close the cover and engage the latches.
Figure 6. Battery Removal and Installation
The CLS scale uses a supplied lithium-ion battery to supply power to the indicator when using a wireless version of the CLS-
420. The lithium-ion battery is located on the top of the cover plate in a painted enclosure.
Charging the Lithium-Ion Battery
The lithium-ion battery comes with a two-bay, level-3 stand alone smart battery charger, a DC power jack and AC power cord.
The average charge time for the battery is eight hours each.
Figure 7. Two-Bay Battery Charger and Parts for the Lithium-Ion Battery
Part No. Description
96343 Lithium-Ion Battery
96344 2-Bay Battery Charger
96345 10-Bay Battery Charger
Table 1. Battery Replacement Parts
Battery Removal Tab
Battery
On/Off Switch
Latches
To calibrate the battery
pack, press the button on
front label.
230 W. Coleman St. • Rice Lake, WI 54868 • USA
U.S. 800-472-6703 • Canada/Mexico 800-321-6703 • International 715-234-9171 • Europe +31 (0)26 472 1319
Rice Lake Weighing Systems is an ISO 9001 registered company.
© Rice Lake Weighing Systems Specifications subject to change without notice.
www.ricelake.com
PN 101112 Rev B
May 14, 2019
Use the following steps to charge the battery prior to use:
1. Insert the plug end of the power cable into the DC power jack on the battery charger and the AC plug into an outlet.
2. Insert battery into the bay.
3. There is one LED indicator in front of each bay which will illuminate to indicate the status of the battery as follows:
Calibrating the Lithium-Ion Battery
To keep the battery fuel gauge as accurate as possible, it is necessary to run the pack through a recalibration cycle on a
monthly basis. To recalibrate, place the battery in the left bay of the charger and press the button on the front label,
See Figure 7 on page 5. This initiates the recalibration sequence in the left bay only. The process can take up to nine hours to
complete and a recommended recalibration must be done once a month to keep the battery accurate.
Lithium-Ion Battery Specifications
Signal Description
Off No Battery
Green Flashing Fast Charging
Green Solid Fully Charged
Yellow Flashing Recalibrating
Yellow/Green Alternating Recalibrating
Yellow Solid Standby
Red Flashing Error
Table 2. Battery Charging LED Signals
Nominal Capacity 6600 mAh
Nominal Voltage 11.1 V
Charging Method Constant Current
Constant Voltage
Charging Voltage 12.6 V
Charging Current 4.0 A
Charging Time 100% at 8 hours
Ambient Temperature Charge 0º±40ºC (32º-104ºF)
Discharge -20º±60ºC (-4º-140ºF)
Storage -20º±50ºC (-4º-122ºF)
Weight (Maximum) 430 g
Dimensions (Maximum) Depth 22.80 mm
Length 214.0 mm
Volumetric Energy Density 466 Wh/I
Gravimetric Energy Density 167 Wh/kg
Maximum Hours of Charge 24 hours
Nominal Capacity 6600 mAh
Table 3. Battery Specifications
Otros manuales para CLS Series
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Escala de Rice Lake
Rice Lake
Rice Lake SURVIVOR CW-80 Manual de usuario
Rice Lake
Rice Lake SURVIVOR Advantage Series Manual de usuario
Rice Lake
Rice Lake MSI-4260B Manual de usuario
Rice Lake
Rice Lake 350-10 Series Manual de usuario
Rice Lake
Rice Lake DIGI DSX-1000 Manual de usuario
Rice Lake
Rice Lake BenchMark SL Manual de usuario
Rice Lake
Rice Lake RL-DBS Manual de usuario
Rice Lake
Rice Lake RL-350-2 Manual de usuario
Rice Lake
Rice Lake RL101 Manual de usuario
Rice Lake
Rice Lake Summit SB-1000 Manual de usuario
Rice Lake
Rice Lake 550-10 Instrucciones de funcionamiento
Rice Lake
Rice Lake rl-mps-30 Manual de usuario
Rice Lake
Rice Lake RL150-10-5 Manual de usuario
Rice Lake
Rice Lake RoughDeck FXB Manual de usuario
Rice Lake
Rice Lake INT700 Manual de usuario
Rice Lake
Rice Lake BenchMark MS Manual de usuario
Rice Lake
Rice Lake RS-130 Manual de usuario
Rice Lake
Rice Lake iDimension PWD Guía del usuario
Rice Lake
Rice Lake TE Series Manual de usuario
Rice Lake
Rice Lake DHH-10 Manual de usuario
