Renishaw RVP Manual de usuario

RVP user's guide

Document part number: H-1000-3322-05-D

RVP user's guide

www.renishaw.com

Issued 06 2022

General information

ORIGINAL LANGUAGE VERSION

This document may not be copied or reproduced in whole or in part, or transferred to any other media or language by any means, without the

prior written permission of Renishaw.

Disclaimer

WHILE CONSIDERABLE EFFORT WAS MADE TO VERIFY THE ACCURACY OF THIS DOCUMENT AT PUBLICATION, ALL WARRANTIES,

CONDITIONS, REPRESENTATIONS AND LIABILITY, HOWSOEVER ARISING, ARE EXCLUDED TO THE EXTENT PERMITTED BY LAW.

RENISHAW RESERVES THE RIGHT TO MAKE CHANGES TO THIS DOCUMENT AND TO THE EQUIPMENT, AND/OR SOFTWARE AND THE

SPECIFICATION DESCRIBED HEREIN WITHOUT OBLIGATION TO PROVIDE NOTICE OF SUCH CHANGES.

Trade marks

RENISHAW®, the probe symbol and REVO®are registered trade marks of Renishaw plc.

Renishaw product names, designations and the mark ‘apply innovation' are trade marks of Renishaw plc or its subsidiaries.

Other brand, product or company names are trade marks of their respective owners.

Third party licences

Third party licence information can be found in the following UCCsuite installation directory:

…\Renishaw\UCC\Utilities\UCCassist Mark II\Firmware\RVP\Licences

In a typical installation the location address will be:

C:\Program Files (x86)\Renishaw\UCC\Utilities\UCCassist Mark II\Firmware\RVP\Licences

WEEE

The use of this symbol on Renishaw products and / or accompanying documentation indicates that the product should not be mixed with

general household waste upon disposal. It is the responsibility of the end user to dispose of this product at a designated collection point for

waste electrical and electronic equipment (WEEE) to enable reuse or recycling. Correct disposal of this product will help to save valuable

resources and prevent potential negative effects on the environment. For more information, please contact your local waste disposal service

or Renishaw distributor.

RVP user's guide

www.renishaw.com

Issued 06 2022

Warranty

Unless you and Renishaw have agreed and signed a separate written agreement, the equipment and/or software are sold subject to the

Renishaw Standard Terms and Conditions supplied with such equipment and/or software, or available on request from your local Renishaw

office.

Renishaw warrants its equipment and software for a limited period (as set out in the Standard Terms and Conditions), provided that they are

installed and used exactly as defined in associated Renishaw documentation. You should consult these Standard Terms and Conditions to find

out the full details of your warranty.

Equipment and/or software purchased by you from a third-party supplier is subject to separate terms and conditions supplied with such

equipment and/or software. You should contact your third-party supplier for details.

Care of equipment

Renishaw probes and associated systems are precision tools used for obtaining precise measurements and must therefore be treated with

care.

Changes to Renishaw products

Renishaw reserves the right to improve, change or modify its hardware or software without incurring any obligations to make changes to

Renishaw equipment previously sold.

Company registration details

Renishaw plc. Registered in England and Wales. Company no: 1106260. Registered office: New Mills, Wotton-under-Edge, Gloucestershire,

GL12 8JR, UK.

Packaging

To aid end user recycling and disposal the materials used in the different components of the packaging are stated here:

Packaging component Material 94/62/EC code 94/62/EC number

Outer box Non-corrugated fibreboard PAP 21

Storage box Polypropylene PP 05

Packing foam Low density polyethylene LDPE 04

Packaging insert Corrugated fibreboard PAP 20

Stylus box Polypropylene PP 05

Stylus box label Polypropylene PP 05

Bag Low density polyethylene LDPE 04

CAUTION: If it is necessary to return any part of the system please ensure it is packaged carefully. Failure to do so could result in

transit damage for which the customer would be liable. Products supplied in plastic boxes must be returned in the original

packaging.

RVP user's guide

www.renishaw.com

Issued 06 2022

Patents

Features of Renishaw's RVP and associated products (such as REVO-2) are the subjects of one or more of the following patents and patent

applications:

CN100453970

CN101166951

CN101166953

CN101405563

CN101405564

CN101490430

CN101772690

CN102305613

CN102906533

CN103842766

CN105190230

CN105408723

CN105793695

CN107532930

CN107850425

CN109964098

EP1877727

EP1877732

EP1989504

EP2002206

EP2002207

EP2035719

EP2140318

EP2167911

EP2431707

EP2564151

EP2764324

EP3004797

EP3052926

EP3289314

EP3322959

EP3542130

JP2016-533484

JP2018-522240

JP2019-536032

JP2021-193400

JP5196356

JP5350216

JP5425476

JP5653581

JP5658863

JP5706158

JP5851969

JP6013533

JP6199870

JP6348577

JP6510425

JP7042620

US10260856

US10591289

US10627259

US10775159

US2020-0049498

US7533574

US7809523

US7861430

US7885777

US7971365

US8006398

US8186882

US8302321

US8425119

US8474148

US8511898

US8601701

US8756973

US8978261

US9038282

US9366519

US9903713

WO2014/191729

WO2015/049341

RVP user's guide

www.renishaw.com

Issued 06 2022

Product compliance

EU declaration of conformity

Contact Renishaw plc or visit www.renishaw.com/EUCMM for the full EU declaration.

UK declaration of conformity

Contact Renishaw plc or visit www.renishaw.com/UKCMM for the full UK declaration.

EMC conformity

This equipment must be installed and used in accordance with this installation guide. This product is intended for industrial use only and

should not be used in a residential area or connected to a low voltage power supply network which supplies buildings used for residential

purposes.

FCC (USA only)

Information to user (47 CFR 15.105)

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These

limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to

cause harmful interference, in which case you will be required to correct the interference at your own expense.

Information to user (47 CFR 15.21)

The user is cautioned that any changes or modifications not expressly approved by Renishaw plc or authorised representative could void the

user's authority to operate the equipment.

Equipment label (47 CFR 15.19)

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

RVP user's guide

www.renishaw.com

Issued 06 2022

ICES-001 (Canada only)

This ISM device complies with Canadian ICES-001(A) / NMB-001(A).

Cet appareil ISM est conforme à la norme ICES‐001﴾A﴿ / NMB‐001﴾A﴿ du Canada.

REACH regulation

Information required by Article 33﴾1﴿ of Regulation ﴾EC﴿ No. 1907/2006 ﴾“REACH”﴿ relating to products containing substances of very high

concern (SVHCs) is available at:

www.renishaw.com/REACH

China RoHS

Contact Renishaw plc or visit www.renishaw.com/ChinaRoHSCMM for the full China RoHS tabulation.

RVP user's guide

www.renishaw.com

Issued 06 2022

Safety

Before unpacking and installing the RVP system, the user should carefully read the safety instructions below and ensure that they are followed

at all times by all operators.

The RVP vision probe system should only be used with the REVO-2 head.

Operators must be trained in the use and application of the REVO-2 system and accompanying products, in the context of the machine it is

fitted to, before being allowed to operate that machine.

Permanent magnets are used in some components of the REVO-2 system and associated products. It is important to keep them away from

items which may be affected by magnetic fields, e.g. data storage systems, pacemakers and watches.

WARNING: Avoid touching the probe (including counter balance arms), modules, and ACM when attached to the REVO-2 head,

especially when it is engaged (servo LED green) and the system is ready for measurement. If contact is made with the hardware, the

tool will need to be reconfigured before continuing.

VM10, VM11-2 and VM12 LED emissions

The vision modules incorporate high power LED lights and should not be used in the event of serious damage to any part of the VM10,

VM11-2 or VM12 modules. In such cases immediately disconnect the power source, remove and do not attempt to reuse the parts. Contact

your supplier for advice.

CAUTION: This equipment uses LED illumination that may flash at a variable rate. Avoid exposure or seek advice from your

medical practitioner if you are susceptible to photosensitivity or related health effects.

RVP user's guide

www.renishaw.com

Issued 06 2022

Environmental and electrical specifications

Environmental specification

Ambient operating temperature range +10 °C to +40 °C

Storage temperature range ‐25 °C to +70 °C ﴾‐13 °F to 158 °F﴿

Operating humidity 0% to 80% (non-condensing)

Storage humidity 0% to 80% (non-condensing)

Electrical specification

The REVO-2 head and probe electronics are powered from the UCC S5. The head motors are powered from the SPA3. The VPCP and VMCP

are powered by a separate power supply that is supplied by Renishaw. Any additional backlighting is powered by a separate power supply

that is supplied by Renishaw. No additional power supplies are required.

RVP user's guide

www.renishaw.com

Issued 06 2022

References and associated documents

The following Renishaw documents are referred to in this document or may be a source of further relevant information. They can easily be

acquired from Renishaw web site www.renishaw.com.

Title Document number

Installation and user's guide: REVO-2 and RSP2 H-1000-7590

Installation and user's guide: RSP3 H-1000-5124

Installation and user's guide: SFP2 H-1000-5365

User's guide: RVP H-1000-3322

User's guide: RFP1 H-1000-5430

Installation guide: UCC S5 H-1000-7598

Installation guide: SPA3-2 H-1000-5364

Installation & user's guide: MCUlite-2, MCU5-2 and MCU W-2 H-1000-5280

Installation and user's guide: MRS modular rack system H-1000-5088

Installation guide: MRS2 modular rack system H-1000-5255

Installation guide: REVO-2 change system port spacing guide H-1000-5408

Technical specifications guide: Styli and accessories H-1000-3200

RVP user's guide

www.renishaw.com

Issued 06 2022

System description

RVP is a non-contact vision measurement probe for use with the REVO-2 5-axis measurement system on co-ordinate measuring machines.

RVP increases the multi-sensor capability of REVO-2 by adding non-contact inspection to the existing touch-trigger, high-speed tactile

scanning and surface finish capability of the system.

The RVP system comprises a probe and a range of modules that are automatically interchangeable with all other probe options available for

REVO. This flexibility means that the optimum tool can be selected to inspect a wide range of features, all on one CMM platform.

The RVP system is managed by the same I++ DME compliant interface as REVO-2 and full user functionality is provided by Renishaw's

MODUS metrology software. New MODUS vision software capability includes RVP configuration, image processing with application specific

options and automatic image storage for review and further analysis.

RVP user's guide

www.renishaw.com

Issued 06 2022

Otros manuales para RVP

Tabla de contenidos

Otros manuales de Instrumento de medición de Renishaw

Renishaw

Renishaw UCC2 Manual de usuario

Renishaw

Renishaw RTP20 Manual de usuario

Renishaw

Renishaw RTS Manual de usuario

Renishaw

Renishaw Equator 300 Manual de usuario

Renishaw

Renishaw XL Series Manual de usuario

Renishaw

Renishaw OMM-S SPRINT Manual de usuario

Renishaw

Renishaw RMP40 Manual de usuario

Renishaw

Renishaw TRS1 Instrucciones de funcionamiento

Renishaw

Renishaw XM-60 multi-axis calibrator Manual de usuario

Renishaw

Renishaw TS34 Manual de usuario

Renishaw

Renishaw RENGAGE RMP400 Manual de usuario

Renishaw

Renishaw SP80 Guía de configuración rápida

Renishaw

Renishaw RMI-QE Manual de usuario

Renishaw

Renishaw XK10 Manual de usuario

Renishaw

Renishaw MP7 Manual de usuario

Renishaw

Renishaw Equator Gauge Checker Manual de usuario

Renishaw

Renishaw P-GA01-0001 Manual de usuario

Renishaw

Renishaw SP80 Manual de usuario

Renishaw

Renishaw OMP40 Manual de usuario

Renishaw

Renishaw NC1 Instrucciones de funcionamiento

Renishaw

Renishaw HCU2 Manual de usuario

Renishaw

Renishaw RMP40 Manual de usuario

Renishaw

Renishaw RMP600 Manual de usuario

Renishaw

Renishaw PH10 PLUS Series Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario