Renesas H8/3864 Series Manual de usuario
H8/3864 Series
QFP-80A
User System Interface Cable
(HS3864ECH61H)
for E6000 Emulator
User’s Manual
HS3864ECH61HE(D)
Cautions
1. Renesas neither warrants nor grants licenses of any rights of Renesas’s or any third party’s
patent, copyright, trademark, or other intellectual property rights for information contained in
this document. Renesas bears no responsibility for problems that may arise with third party’s
rights, including intellectual propertyrights, in connection with use of the information contained
in this document.
2. Products and product specifications may be subject to change without notice. Confirm that you
have received the latest product standards or specifications before final design, purchase or use.
3. Renesas makes every attempt to ensure that its products are of high quality and reliability.
However, contact Renesas’s sales office before using the product in an application that demands
especially high quality and reliability or where its failure or malfunction may directly threaten
human life or cause risk of bodily injury, such as aerospace, aeronautics, nuclear power,
combustion control, transportation, traffic, safety equipment or medical equipment for life
support.
4. Design your application so that the product is used within the ranges guaranteed by Renesas
particularly for maximum rating, operating supply voltage range, heat radiation characteristics,
installation conditions and other characteristics. Renesas bears no responsibility for failure or
damage when used beyond the guaranteed ranges. Even within the guaranteed ranges, consider
normally foreseeable failure rates or failure modes in semiconductor devices and employ
systemic measures such as fail-safes, so that the equipment incorporating Renesas product does
not cause bodily injury, fire or other consequential damage due to operation of the Renesas
product.
5. This product is not designed to be radiation resistant.
6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document
without written approval from Renesas.
7. Contact Renesas’s sales office for any questions regarding this document or Renesas
semiconductor products.
i
Preface
Thank you for purchasing this user system interface cable (HS3864ECH61H) for the Renesas’s
original microcomputer H8/3864 series and H8/3887 series.
The HS3864ECH61H is a user system interface cable that connects an H8/3864 series, H8/3887
series E6000 emulator (HS3880EPI60H; hereinafter referred to as the emulator) to the IC socket for
a QFP-80A package (package code: FP-80A) for the H8/3864 series MCU on the user system.
ii
Contents
Section 1 Configuration....................................................................................1
Section 2 Connection Procedures......................................................................4
2.1 Connecting User System Interface Cable to Emulator Station .........................................4
2.2 Connecting User System Interface Cable to User System................................................5
2.2.1 Installing IC Socket .............................................................................................5
2.2.2 Soldering IC Socket.............................................................................................5
2.2.3 Inserting Cable Head ...........................................................................................5
2.2.4 Fastening Cable Head..........................................................................................6
2.2.5 Connecting Cable Body to Cable Head ...............................................................8
2.3 Recommended Dimensions for User System Mount Pad.................................................9
2.4 Dimensions for User System Interface Cable Head..........................................................10
2.5 Resulting Dimensions after Connecting User System Interface Cable.............................11
Section 3 Installing the MCU to the User System.............................................12
Section 4 Verifying Operation...........................................................................14
Section 5 Notice ................................................................................................16
Section 1 Configuration
1
UTIONCA
Use an IC149-080-017-B5 socket (manufactured by
YAMAICHI ELECTRONICS Co., Ltd.) for the FP-80A
package IC socket on the user system.
Figure 1 shows the configuration of the HS3864ECH61H user system interface cable for the
FP-80A package.
User system
IC socket
Cable head
Screws (M2 x 12 mm)
with flat washers
Screws (M2 x 8 mm)
with flat washers
Socket cover
(for fastening cable head)
To emulator station
Cable body
Figure 1 HS3864ECH61H User System Interface Cable
2
3
Table 1 lists the HS3864ECH61H components. Please make sure you have all of these components
when unpacking.
Table 1 HS3864ECH61H Components
No. Component Quantity Remarks
1 Cable body 1 Includes flat cable
2 Cable head 1
3 IC socket 1 For the FP-80A package
4 Socket cover 1 For installing an FP-80A-packaged MCU
5 Screws (M2 x 12 mm) 4 For fastening cable head
6 Screws (M2 x 8 mm) 4 For installing an FP-80A-packaged MCU (with four
flat washers)
7 Documentation 1 User’s manual for HS3864ECH61H (this manual)
Section 2 Connection Procedures
2.1 Connecting User System Interface Cable to Emulator Station
WARNING
Always switch OFF the user system and the emulator
product before the USER SYSTEM INTERFACE CABLE
is connected to or removed from any part. Before connecting,
make sure that pin 1 on both sides are correctly aligned. Failure to
do so will damage the user system and the emulator product or will
result in PERSONAL INJURY. The USER PROGRAM will be
LOST.
To connect the cable body to the emulator station, follow the instructions below.
1. Make sure the user system and emulator station are turned off.
2. After making sure the direction of the cable body connector is correct, firmly insert the cable
body connector into the emulator station socket (figure 2).
6000
Emulator station
E
Cable body
User system interface cable
Figure 2 Connecting User System Interface Cable to Emulator Station
4
2.2 Connecting User System Interface Cable to User System
WARNING
Always switch OFF the user system and the emulator
product before the USER SYSTEM INTERFACE CABLE
is connected to or removed from any part. Before connecting,
make sure that pin 1 on both sides are correctly aligned. Failure to
do so will damage the user system and the emulator product or will
result in PERSONAL INJURY. The USER PROGRAM will be
LOST.
To connect the cable head to the user system, follow the instructions below.
2.2.1 Installing IC Socket
After checking the location of pin 1 on the IC socket, apply epoxy resin adhesive to the bottom of
the IC socket for an FP-80A package, and fasten it to the user system before soldering.
2.2.2 Soldering IC Socket
After fastening, solder the IC socket for an FP-80A package to the user system. Be sure to
completely solder the leads so that the solder slops gently over the leads and forms solder fillets.
(Use slightly more solder than the MCU.)
2.2.3 Inserting Cable Head
CAUTION
Check the location of pin 1 before inserting.
Align pin 1 on the IC socket for an FP-80A package on the user system with pin 1 on the user system
interface cable head, and insert the user system interface cable head into the IC socket on the user
system, as shown in figure 3.
5
2.2.4 Fastening Cable Head
6
UTIONCA
1. Use a Phillips-type screwdriver whose head matches
the screw head.
2. The tightening torque must be 0.0785 N•m or less.
If the applied torque cannot be accurately measured,
stop tightening when the force required to turn the screw
becomes significantly greater than that needed when first
tightening. If a screw is tightened too much, the screw
head may break or an IC socket contact error may be caused
by a crack in the IC socket solder.
3. If the emulator does not operate correctly, cracks might
have occurred in the solder. Check conduction with
a tester and re-solder the IC socket if necessary.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Hardware de computadora de Renesas
Renesas
Renesas P9415-R-EVK Manual de usuario
Renesas
Renesas RS-485 Manual de usuario
Renesas
Renesas M3T-42DIP-DMS Manual de usuario
Renesas
Renesas REJ06B0734-0100 Instrucciones de instalación y funcionamiento
Renesas
Renesas RSKM16C62P Manual de usuario
Renesas
Renesas RTE7701201CFK144T000R Manual de usuario
Renesas
Renesas H8S/2100 Series Manual de usuario
Renesas
Renesas Emulator System E8 Manual de usuario
Renesas
Renesas Converter Board M30291T-64FPD Manual de usuario
Renesas
Renesas RA4T1 Manual de usuario
Renesas
Renesas M38C29T-ADF Manual de usuario
Renesas
Renesas User System Interface Board HS7047ECH61H Manual de usuario
Renesas
Renesas PC7501 Manual de usuario
Renesas
Renesas 32176 Manual de usuario
Renesas
Renesas R0E510Y47LVB00 Manual de usuario
Renesas
Renesas RX Series Manual de usuario
Renesas
Renesas H8S/2646 Series Manual de usuario
Renesas
Renesas M3T-DUMMY80 Manual de usuario
Renesas
Renesas R8C/15 Instrucciones de operación
Renesas
Renesas M32R-FPU Instrucciones de montaje
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
