ReChargx RX411 Manual de usuario

TonerRellKits.com ReChargX™RX411

ReChargX™ RX411 Instructions

For relling the Dell 593-BBKC (CVXGF/2RMPM) and

593-BBKD (P7RMX/PVTHG) toner cartridges

Dell 593-BBKC & 593-BBKD toner cartridge

ReChargX™ RX411 premium print toner rell kit

Tools needed to properly rell your cartridge using the

ReChargX™ RX411 toner rell kit.

ReChargX™ RX411 Instructions: Overview

The Dell 593-BBKC (CVXGF/2RMPM) and 593-

BBKD (P7RMX/PVTHG) are the cartridges frequently

found in the following Dell printer models (and all

other machines using the same “engine”):

E310dw E514dw

E515dn E515dw

The Dell 593-BBKC (CVXGF/2RMPM) Standard-

Yield and 593-BBKD (P7RMX/PVTHG) High-Yield

cartridges are easy to rell using our ReChargX™

RX411 premium print toner rell kit.

Included in the ReChargX™ RX411 Kit

• ReChargX™ RX411 instructions

• ReChargX™ RX411 premium print toner

• ReChargX™ RX411 reset gear & spring

• ReChargX™ RX411 toner hopper plug

• Residual toner bag

• Reminder labels (2)

• Toner bottle funnel spout

• “Toner grabber” cloth

• Work surface protector/newsprint

Required Tools

The toner rell process requires the use of the

following tools (which, if you need them, are available

in our ReChargX™ Brother tool kit):

• Small phillips-head screwdriver

• Small at-blade screwdriver

TonerRellKits.com ReChargX™RX411

Note: Please make certain the printer is powered

“ON” throughout the entire rell procedure. Failure to

do so may cause the printer to be unable to identify

that the cartridge has been relled.

Step 1: Prepare your work surface

Included in the ReChargXTM RX411 premium print

toner rell kit is a sheet of newsprint (Figure 1).

Unfold the sheet and lay it across your work surface.

The newsprint keeps your work surface clean and is

discarded after completing the relling process.

Step 2: Position the drum unit and toner

cartridge assembly

When you remove the cartridge from your printer the

drum unit will still be attached.

Position the assembly on your work surface so the

handle on the front of the toner cartridge (A) is facing

you and the green or blue tab (B) is on the left-hand

side (Figure 2).

Step 3: Separate the toner cartridge from the

drum unit assembly

Press and hold down the green or blue tab (A)

located on the left-hand side of the unit while lifting

up on the handle of the front of the toner cartridge

with your right hand (B) to separate the toner

cartridge from the drum unit (Figure 3).

Lift the toner cartridge up and off of the drum unit.

Note: Since the drum in the drum unit can be easily

scratched or damaged, put it out of harm’s way until

we are completely nished with the relling operation.

Step 4: Prepare the cartridge for relling

Position the cartridge on your work surface so the

handle (A) is facing toward you and the developer

roller (B) is facing away from you (Figure 4).

Figure 1: ReChargX™ newsprint work surface protector

Figure 2: Positioning the drum unit and toner cartridge assembly

Figure 3: Removing the cartridge from the drum unit

Figure 4: The toner cartridge in the correct orientation

TonerRellKits.com ReChargX™RX411

Step 5: Protect the developer roller

The developer roller along the front of the cartridge is

critical to the image production process and can be

damaged even by a ngerprint.

To protect the roller during relling we will cover it

with a sheet of paper.

Start with a piece of paper in “portrait” orientation,

then fold the 8.5” X 11” sheet in half (folding the

top edge over to meet the bottom edge) leaving an

8.5” X 5.5” sheet.

With the cartridge face up tape one of the long 8.5”

edges to the top of the cartridge (Figure 5-1).

Carefully fold the paper over the developer roller

(again, being careful not to touch the roller with your

ngers) and tape the other edge of the paper to the

bottom of the cartridge (Figure 5-2).

Step 6: Remove the cartridge end cap

Position the cartridge on your work surface so the

black plastic end cap (which covers the internal gears

of the cartridge) is facing upward and the handle of

the cartridge is on the right-hand side (Figure 6-1).

You now have access to the two screws which

secure the end cap to the cartridge (highlighted by

the arrows in Figure 6-1).

Using the phillips-head screwdriver remove the two

phillips-head screws (Figure 6-2 and Figure 6-3) and

set them aside for later use.

After removing the two phillips-head screws, lift the

black end cap up and away from the cartridge body

to expose the gear train and set the end cap aside.

Figure 5-1: Protecting the developer roller (front-side)

Figure 5-2: Protecting the developer roller (back-side)

Figure 6-1: Cartridge positioned with end cap facing up

Figure 6-2: Removing the cartridge end cap screws (1 of 2)

Figure 6-3: Removing the cartridge end cap screws (2 of 2)

TonerRellKits.com ReChargX™RX411

Dell uses a “page counting” mechanism (a

combination of gears and “ags”) to report to the

printer when the cartridge is either full or used.

Before we begin the rell procedure we will address

the components of the reset mechanism that either

have to be removed or replaced.

Without properly resetting/addressing these

mechanisms, even after the cartridge has been

relled the cartridge would still appear to the printer

as being empty resulting in a false “toner low” or

“toner empty” message.

Although the starter, standard-yield, and high-yield

toner cartridges are fundamentally the same, each

requires a slightly different process to reset the page

counting mechanism.

Skip forward to the appropriate page for the reset

procedures specic to your cartridge.

If you are working on a starter cartridge (the

cartridge included with the printer) proceed to page 5

and follow steps 7a-7c.

If you are working on a standard-yield cartridge

proceed to page 6 and follow steps 8a-8e.

If you are working on a high-yield cartridge,

proceed to page 8 and follow steps 9a-9e.

Figure A: The starter cartridge (with end cap removed)

Figure B: The standard-yield cartridge (with end cap removed)

Figure C: The high-yield cartridge (with end cap removed)

Identifying the toner cartridge type

TonerRellKits.com ReChargX™RX411

Preparing the starter cartridge for relling and resetting

Figure 7-1: The starter cartridge (end cap removed)

Figure 7-2: After removing the starter drive gear; before

removing the actuator gear

Figure 7-3: After removing the starter actuator gear; before

removing the toner hopper plug

Figure 7-4: Removing the starter toner hopper plug

Remove the components

Figure 7-1 shows the gear end of the TN starter

cartridge (the cartridge that came with the machine

when it was new) with the end cap removed.

The components you will be removing (to be replaced

with the new components which came with the

RX411 toner rell kit to convert your cartridge into a

high-yield cartridge) are the drive gear (A), actuator

gear (B) and toner hopper plug (C).

Step 7a: Remove the drive gear

To prepare for the resetting of the starter toner

cartridge and its conversion into the equivalent of the

high-yield cartridge, we start by removing the drive

gear (A) (Before: Figure 7-1; After: Figure 7-2).

Step 7b: Remove the actuator gear

With the drive gear removed, we can remove the

actuator gear (B) from the gear train (Before: Figure

7-2; After: Figure 7-3).

Step 7c: Remove the toner hopper plug

With the drive and actuator gears out of the way we

will remove the toner hopper plug (C).

Using the edge of the opening as support, wedge the

tip of a at-blade screwdriver between the lip of the

toner hopper opening and the toner hopper plug.

Then pry the plug up and out (Figure 7-4).

Now that we have removed the starter gears and

toner hopper plug, proceed to page 10 to continue

the process.

TonerRellKits.com ReChargX™RX411

Figure 8-1: The standard-yield cartridge (end cap removed)

Figure 8-2: After removing the reset spring; before removing the

reset gear

Figure 8-3: After removing the reset gear; before removing the

drive gear

Preparing the standard-yield cartridge for relling and resetting

Remove the components

Figure 8-1 shows the gear end of the standard-yield

toner cartridge with the end cap removed.

The components you will be removing (to be replaced

with the new components which came with the

RX411 toner rell kit to convert your cartridge into a

high-yield cartridge) are the drive gear (A), actuator

gear (B), reset gear (C), reset spring (D) and toner

hopper plug (E), which is located under the reset

gear and not visible in this gure.

Step 8a: Remove the reset spring

To begin the process of converting the standard-yield

into the high-yield, we start by removing the reset

spring (D) (Before: Figure 8-1; After: Figure 8-2).

Step 8b: Remove the reset gear

With the reset spring removed, you may now remove

the black reset gear (C) (Before: Figure 8-2; After:

Figure 8-3) which will expose the toner hopper plug.

TonerRellKits.com ReChargX™RX411

Figure 8-4: After removing the drive gear; before removing the

actuator gear

Figure 8-5: After removing the actuator gear; before removing

the toner hopper plug

Figure 8-6: Removing the toner hopper plug

Step 8c: Remove the drive gear

With the reset gear removed, we will now remove

the drive gear (A) from the gear train (Before: Figure

8-3; After: Figure 8-4).

Step 8d: Remove the actuator gear

With the drive gear removed we will now remove the

actuator gear (B) from its post (Before: Figure 8-4;

After: Figure 8-5).

Step 8e: Remove the toner hopper plug

With the drive, reset, and actuator gears out of the

way we now have access to the hopper plug (E).

Wedge the tip of a at-blade screwdriver between the

lip of the toner hopper opening and the toner hopper

plug. Then pry the plug up and out (Figure 8-6).

Now that we have removed the spring, gears, and

toner hopper plug, proceed to page 10 to continue

the rell process.

TonerRellKits.com ReChargX™RX411

Figure 9-1: The high-yield cartridge (end cap removed)

Figure 9-2: After removing the reset spring; before removing the

reset gear

Figure 9-3: After removing the reset gear; before removing the

drive gear

Preparing the high-yield cartridge for relling and resetting

Remove the components

Figure 9-1 shows the gear end of the high-yield toner

cartridge with the end cap removed.

The parts you will be working with are the drive gear

(A), actuator gear (B), reset gear (C), reset spring (D)

and toner hopper plug (E), which is located under the

reset gear and not visible in this view.

Step 9a: Remove the reset spring

To prepare for the resetting we start by removing the

cartridge reset spring (D) (Before: Figure 9-1; After:

Figure 9-2).

Step 9b: Remove the reset gear

With the reset spring removed we will now remove

the reset gear (C) which will expose the toner hopper

plug (Before: Figure 9-2; After: Figure 9-3).

TonerRellKits.com ReChargX™RX411

Figure 9-4: After removing the drive gear; before removing the

actuator gear

Figure 9-5: After removing the actuator gear; before removing

the toner hopper plug

Figure 9-6: Removing the toner hopper plug

Step 9c: Remove the drive gear

With the reset gear out of the way, we will now

remove the drive gear (A) from the cartridge gear

train (Before: Figure 9-3; After: Figure 9-4).

Step 9d: Remove the actuator gear

With the drive gear removed, we will now remove

the actuator gear (B) (Before: Figure 9-4; After:

Figure 9-5).

Step 9e: Remove the toner hopper plug

With the reset spring and the reset, drive and

actuator gears out of the way, we will now remove

the toner hopper plug (E) (Figure 9-6).

Wedge the tip of a at-blade screwdriver between the

lip of the toner hopper opening and the toner hopper

plug. Then pry the plug up and out.

Now that we have removed the spring, gears, and

toner hopper plug, proceed to page 10 to continue

the process.

TonerRellKits.com ReChargX™RX411

Figure 10-1: Inserting cartridge into zip-top bag

Figure 10-2: Dumping out the remaining toner

Preparing the cartridges for relling and resetting

Step 10: Remove the remaining toner

Prior to adding “fresh” toner, we must remove the

residual “old” toner.

On the rst rell of your toner cartridge, the new toner

should not be combined with whatever quantity of

toner that remains in the hopper.

Failure to remove the remaining toner will result in

splotching, smudging, hazing, and other print defects.

Note: This step does not need to be performed on

subsequent rells when fresh ReChargX™ toner is

being added to the existing ReChargX™ toner.

Insert the toner hopper opening end of the cartridge

into the plastic zip-top bag which is included in the

ReChargX™ RX411 toner rell kit (Figure 10-1).

Carefully pour out as much of the residual toner as

possible (tapping along the side of the cartridge helps

to keep the toner owing) (Figure 10-2).

If the toner stops owing, stand the cartridge upright

(with the toner hopper hole facing up) and then put

the end of the cartridge back into the bag and

continue the emptying process.

With the majority of the toner removed, remove the

cartridge from the bag. Seal the bag and discard it.

Otros manuales de Accesorios de impresora de ReChargx

ReChargx

ReChargx RX006 Manual de usuario

ReChargx

ReChargx RX163 Manual de usuario

ReChargx

ReChargx RX201X Manual de usuario

ReChargx

ReChargx RX052 Manual de usuario

ReChargx

ReChargx RX207 Manual de usuario

ReChargx

ReChargx RX237 Manual de usuario

ReChargx

ReChargx RX230X Manual de usuario

ReChargx

ReChargx RX022 Manual de usuario

ReChargx

ReChargx RX211 Manual de usuario

ReChargx

ReChargx RX230A Manual de usuario

ReChargx

ReChargx RX160 Manual de usuario

ReChargx

ReChargx RX292 Manual de usuario

Manuales populares de Accesorios de impresora de otras marcas

Star Micronics

Star Micronics TSP800 Series Manual de usuario

REA

REA JET HR pro 2K Manual de usuario

HP Laserjet,Color Laserjet 4si Manual de usuario

oliser

oliser MS 45 Manual de usuario

Roland

Roland DU2-64 Instrucciones y recetas

Xerox

Xerox EFI EXP6000 Manual de usuario

Canon

Canon Finisher-T1 Manual de usuario

Sharp

Sharp FO-1MK Manual de usuario

Labelmate

Labelmate PM-300 Manual de usuario

Epson

Epson T6248 Manual de funcionamiento

Epson

Epson OT-BZ20 Manual de usuario

Canon

Canon TonerRobot EP-27 Manual de usuario

Ricoh

Ricoh LCIT RT5100 Guía de inicio rápido

GBC

GBC 16 Series Manual de usuario

Canon

Canon INNER 2-WAY TRAY-E1 Manual de operación y mantenimiento

Develop

Develop SD-509 Manual de usuario

Kyocera

Kyocera KM-6230 Manual

Triumph Adler

Triumph Adler DF-710 Manual