Rain Bird ESP-MC Manual de usuario

INSTALLATION and OPERATING

INSTRUCTIONS

Controller Unit ESP-MC

Introduction

Welcome to Rain Bird! Thank you for purchasing your new, state-of-the-art Rain Bird

controller. For more than six decades, Rain Bird has led the irrigation industry in meet-

ing all of your water management needs by providing the highest quality products and

services available. Your new Rain Bird controller is designed to give you a lifetime of

on-site watering control.

The ESP-MC Controller

The Extra Simple Programming-MAXICOM Compatible series (ESP-MC) controller is a

stand-alone controller appropriate for residential or commercial use. Its easy-to-use

built-in computer offers four programs for up to 40 watering stations. The ESP-MC can

also be upgraded to function as a satellite controller that is part of the MAXICOM irri-

gation system.

For more information about using your controller with the MAXICOM system, see the

ESP-SAT Installation and Operating Instructions manual that comes with the ESP-SAT

and with the MAXICOM interface board (MIB) for the ESP-MC.

Special Features

The ESP-MC is available as a wall-mount (WM) model in 8, 12, 16, 24, 32, or 40 sta-

tion capability. For information about pedestals, contact your Rain Bird distributor. All

ESP-MC models have the following special features:

• Anti-rust, corrosion-resistant design

• Four independent programs

• Cycle + Soak feature for water conservation and erosion control

• Program and time keeping during power outage

• Diagnostic circuit breaker that identifies a station with a short circuit

• Convenient Test Program

• Rain Delay from 1 to 99 days

• 365-day calendar with various scheduling options for watering cycles

• Option to set any day of the month as a non-watering day

• Cycle and fault indicator lights

• Easy-to-read liquid crystal display

• Optional moisture sensors that suspend watering when the soil is wet

• Universal remote-ready connections

• True independent day cycles by program

• Programmable program overlap

• Station timing from one minute to 12 hours

Packing List

Please check to make sure that you have all the items on the list. If any item is missing

or damaged, contact your Rain Bird distributor.

• 1 Pre-assembled Controller in Wall Cabinet

• 1 Bag of Mounting Hardware

• 2 Keys

• 1 9-Volt Rechargeable Battery

• 1 Installation and Operating Instructions Manual

• 1 Mounting Template

• 1 Three-year Warranty Card

Chapter 1: Installation

This section of the manual explains how to mount your new ESP-MC controller on the

wall and how to connect the wiring.

Mounting the Controller

Before You Begin

Important: Before installing your controller, make sure that the area around you is

free from dirt and dust and that your hands and arms are clean. This will avoid con-

tamination of the controller’s internal parts.

Warning! Do not let water or other liquids come in contact with any part inside the

metal cabinet.

Choosing a Location

When choosing the best location to install your wall-mount controller, please consider

the following:

Warning! This controller must be installed in compliance with local electrical codes.

ü Select an area, protected from vandalism, where the user can easily reach the con-

troller. We recommend placing the controller in a utility room.

ü Select a location that has access to 120 volt AC electrical power (or the proper

electrical supply voltage outside the United States).

ü Choose a flat, stable, vertical surface, where you can mount the controller. Allow

sufficient conduit clearance for the electrical connections at the bottom of the metal

cabinet.

ü Allow 14” (35.9 cm) minimum clearance for the hinged cabinet door to swing fully to

the left.

What You Will Need

Before you begin installation, you will need the following tools:

ü Phillips Head Screwdriver

ü Slotted Head Screwdriver

ü Slotted Thin Blade Screwdriver

ü Wire Strippers

ü Lineman’s Pliers

ü Needlenose Pliers

ü Tape Measure

ü Marking Pencil

ü Electric Drill (or Hammer Drill if installing in masonry or concrete wall)

ü Nut Driver

14” (36 cm)

minimum 11-1/4”

(28.8 cm)

Cabinet is

6-5/8” (17 cm)

To Fuse

Box

Wall

Floor

Valve Wiring in Conduit

120 Volt AC

Wiring in Conduit

11-3/8”

(28.2 cm)

Locate for

easy access

and for

comfortable

Typical Wall-mount Installation

Chapter 1: Installation(Continued)

Removing the Controller’s Faceplate

In order to mount the controller, you must first remove the faceplate. To do so:

1. Remove the controller cabinet door from its two hinges by opening the door then

holding the bottom of the door and sliding up.

2. Pull out gently on the two white plastic snap latches on the right side of the face-

plate, then swing the panel open.

3. Disconnect the two-wire harness from the terminal board by pressing the latch away

from the connector and pulling the connector away from the terminal board. Discon-

nect the wide gray ribbon cable by grasping the wide sides of the connector and

gently pulling the connector away from the terminal board.

4. Remove the faceplate from its hinges by pushing up gently on the panel until the

lower hinge comes up out of its hole. Slide the faceplate down and away to clear

the upper hinge from its hole. Set the faceplate aside.

5. Remove the white foam block from inside the controller. Remove the 9-volt battery

from the foam block.

Mounting the Controller on the Wall

Pick up the metal cabinet. Using a thin blade screwdriver, push out the three largest

plastic plugs at the back of the cabinet. The three new holes should form an up-side

down triangle.

1.Place the mounting template onto your mounting surface, then drill the holes.

2.Mount the controller cabinet with the mounting hardware supplied.

Note: The mounting materials and specific screws you need will vary according to the

kind of mounting surface (i.e. wood, cement, masonry, drywall, etc.).

(See illustrations on the following page.)

Step 1 Step 2 Disconnecting two-wire harness

Disconnecting ribbon wire

Connecting the Controller

There are three types of connections you must make to your ESP-MC controller:

• connections to the field valves,

• grounding connections, and

• connections to the main power source.

You may also want to connect an optional sensor, which prevents watering during

rainfall or when the soil is moist.

This section of the manual contains instructions for all four types of connections.

Note: If you are installing an ESP-SAT controller, see the ESP-SAT Installation and

Operating Instructions Manual for information about connecting the controller to the

cluster control unit.

Important: All wiring must be installed and connected in accordance with local codes.

Connections to the Field Valves

Each valve that is controlled by the ESP-MC must have its own wire that is connected

to a numbered station terminal on the controller’s terminal strip. Each station terminal

is capable of operating two valves.

Important: The wires you use to connect the controller to the field valves must be ap-

proved for underground use. See the Rain Bird catalog for exact wire specifications.

Important: Do not install the valve wires in the same conduit as the wires to the main

power source.

The illustrations below demonstrate Mounting the Controller.

Remove the faceplate from hinges Three plastic plugs

To connect the valve wires:

1. Feed each valve wire up through the large hole on the bottom of the controller cabi-

net.

2. Strip 1/2” (1.3 cm) from the end of the valve wire. Insert the wire into the appropriate

station terminal. If the wire does not enter securely into the hole, press down on the

orange lever as you insert the wire.

Note: Each station has two holes (one above the other) because each station is capa-

ble of operating two valves.

3.Repeat for all used stations.

4.Attach the valve common wire to one of the two common terminals in the same way.

5. If your system includes a master valve or a 24 volt pump start relay, connect the

wire from that device to the MV (master valve) terminal on the controller the same

way you connected the other wires.

Note: MV2 (master valve 2) is enabled when any station operates. MV1 (master valve

Personal Wiring Notes:

_______________________________________________________________________________________________________

Insertion of the Valve Wire:

Grounding Connections

The ESP-MC is equipped with built-in electrical surge protection. For this system to

function, the earth ground terminal on the controller must be connected to a ground

rod that is driven into the earth.

Important: Use a #10 (6 mm) or #8 (10 mm) bare wire to connect the controller to the

ground-rod. Use a standard copper clad, 5/8" (1.6 cm) diameter, 8 ' (0.6 m) long rod.

To connect the ground wire,

1. Feed the ground wire up through the large hole at the bottom of the controller cabi-

net (the same hole used for the valve wires).

2.Loosen the screw on the copper earth ground terminal and place the ground wire

into the terminal. Tighten the screw so that the ground wire is secure.

Connections to the Main Power Source

The three main power input wires for the standard 117 volt, 60 Hz/AC transformer are

black, white, and green. The international version 230 volt, 50 Hz wires are black,

white, and green and yellow. These wires exit the controller through the smaller hole

at the bottom of the controller cabinet.

Important: The wires that connect the controller to the main power source must be in-

stalled in a conduit other than the one that contains the field wires.

Insertion of the Ground Wire:

Location of Junction Box:

To connect the power input wires to the main power source,

1. Connect a junction box to the transformer nipple. To do this, place the junction box

on the nipple, then thread the washer on. Twist it to tighten.

2. If you have the standard 117 volt, 60 Hz model, use wire nuts to connect the black

wire to the power source hot wire, the white wire to the common wire, and the green

wire to the ground wire.

If you have a 230 volt, 50 Hz model, use wire nuts to connect the black wire to the

power source hot wire, and the white to the power source common wire. Connect

the green and yellow wire to the ground wire.

3.Close the junction box.

4.Install a conduit for the wires from the power source to the junction box.

Main Power Wire Connections:

Connections to an Optional Sensor

The ESP-MC controller allows you to connect an optional sensor. The ESP-MC works

with any open or closed switch sensor such as the Rain Bird Raincheck.

Important: The wires you use to connect the controller to the sensor must be ap-

proved for underground use. See the Rain Bird catalog for exact wire specifications.

Important: The sensor wires should be installed in a conduit other than the one that

contains the wires to the main power source.

To connect the sensor’s wires to the controller:

1.Remove the yellow jumper wire between the two sensor terminals.

2. Strip 1/2” (1.3 cm) from the end of the sensor wires. Insert one wire to each of the

sensor terminal holes. If the wire does not enter securely into the hole, press down

on the orange lever as you insert the wire.

Connecting the sensor’s wires to the controller (Continued)

3. Route the wires out of the controller through the large hole at the bottom of the con-

troller cabinet

4.Connect the other end of the wires to the sensor’s valve common terminals or wires.

5.Follow the sensor’s directions for placing and connecting the sensor’s probes and

for setting the shutoff level, if appropriate.

Putting the Controller Back Together

Congratulations! You have completed the mounting and wiring of your new ESP-MC

controller. To put the controller back together:

1. Replace the controller’s face plate by slipping it into the hinges.

2. Plug the two-wire connector and the ribbon cable connector back into the terminal

board.

3. Detach the recharging clip from its retainer at the back of the face plate. Snap the

recharging clip onto the 9 volt battery supplied. Then push the battery into the bat-

tery holder.

The ESP-MC fully charges the nickel metal hydride, 9 volt battery in about 48 hours

and continues to charge the battery whenever the controller is supplied with power.

The 9 volt battery provides power for keeping track of what cycle is in progress

when there is a power outage. The 9 volt battery also allows the controller to be

programmed when the face plate is detached from the cabinet. This feature lets the

installer walk a site while setting watering times and schedules.

Note: The ESP-MC also has a built-in lithium battery that provides for non-volatile

program memory.

Warning! Do not use an alkaline battery in the controller; alkaline batteries can cause

an explosion.

4.Re-attach the controller door to its hinges.

Sensor Wire Connection (Step 1):

Otros manuales para ESP-MC

Tabla de contenidos

Otros manuales de Controladores de Rain Bird

Rain Bird

Rain Bird ESP-TM2 Manual de usuario

Rain Bird

Rain Bird PAR+ES Manual de usuario

Rain Bird

Rain Bird PAR+ES Manual de usuario

Rain Bird

Rain Bird ESP-LXD Guía de instalación

Rain Bird

Rain Bird ESP-LX Instrucciones de montaje

Rain Bird

Rain Bird ESP-RZ Manual de servicio

Rain Bird

Rain Bird ESP-9V Manual de usuario

Rain Bird

Rain Bird PRS-DIAL Instrucciones de funcionamiento

Rain Bird

Rain Bird ESP-Me Series Manual de usuario

Rain Bird

Rain Bird ESP-RZXe Manual de usuario

Rain Bird

Rain Bird Image Series Manual de usuario

Rain Bird

Rain Bird WPX Manual de usuario

Rain Bird

Rain Bird ESP-LXME Guía de instalación

Rain Bird

Rain Bird CRC-8A Manual de usuario

Rain Bird

Rain Bird E-6C Manual de instrucciones

Rain Bird

Rain Bird ESP-LX Manual de usuario

Rain Bird

Rain Bird ESP-LXD Manual de usuario

Rain Bird

Rain Bird ESP-LX Plus Series Guía

Rain Bird

Rain Bird RC2-230V Manual de usuario

Rain Bird

Rain Bird IQNCCEN Manual de usuario

Rain Bird

Rain Bird ESP-4 Instrucciones de montaje

Rain Bird

Rain Bird RC2-230V Manual de usuario

Rain Bird

Rain Bird ESP-RZXe Manual de usuario

Rain Bird

Rain Bird E-6C Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario