Quantum QXS-448 Manual de usuario

QXS 48-Drive Rackmount Install

Guide

This document contains the following topics:

Before You Begin 2

Attach side brackets 4

Rails Assembly 5

Install Rails (Square, Round, Pre-tapped Hole-Racks) 7

Install and Secure the Chassis 21

Next Steps 24

DXi V4000, GoVault, Lattus, NDX, the Q logo, the Q Quantum logo, Q-Cloud, Quantum, the Quantum logo, Quantum Be

Certain, Quantum Vision, Scalar, StorageCare, StorNext, SuperLoader, Symform, the Symform logo, vmPRO, and Xcellis

are either registered trademarks or trademarks of Quantum Corporation and its affiliates in the United States and/or other

countries. All other trademarks are the property of their respective owners. Quantum specifications are subject to change.

6-68391-01 Rev C, December 2016 *6-68391-01*

Before You Begin

QXS 48-Drive Rackmount Install Guide 2

Before You Begin

These instructions are for the following systems:

lQXS-448

lQXS-648

Complete the following:

lVerify that the installation site meets the chassis’s requirements for space and airflow, temperature, and

power (see the web-posted setup guide for your chassis).

lConsidering your system configuration and weight distribution, determine where you will install each

chassis within the rack or cabinet. Install the first chassis in the lowest rack space you plan to use. Install

each remaining chassis into the next-higher available space within the rack, until all chassis are secured

in place.

lConfirm that you have cables of appropriate type and length to connect to hosts and to power outlets.

Caution: Be sure you are properly grounded before touching a static-sensitive component to minimize

potential for electronic discharge.

The person using these instructions must be qualified to service and install storage products.

Caution: Two people are needed to lift and move the chassis. Use care to avoid injury.

Required Tools

Required tools include:

l#2 Phillips screwdriver

lAntistatic protection devices.

Before You Begin

QXS 48-Drive Rackmount Install Guide 3

Rackmount Bracket Kit Hardware

Use fasteners that pertain to your rack type.

Code Part description Qty

Rails and brackets

- Side bracket 2

- Left rail (front sleeve with rear insert) 1-ea.

- Right rail (front sleeve with rear insert) 1-ea.

Screws

A #8-32 x 3/16, FH100, PLP, SS 4

B #8-32 x 3/8, FH, PLP2, SS 6

C #10-32 x 3/4, Truss, PLP, SS; or

M5 x 10, PH, PLP2, SS; or

M6 x 10, PH, PLP2, SS; or

#12-24 x 3/8, PH, PLP, SS

D #10-32, Shoulder, Round hole mtg; or

#10-32, Shoulder, Square hole mtg; or

#10-32 x 0.319, FH100, PLP2, SS; or

M5 x 8.4, FH, PLP2, SS; or

M6 x 9.4, FH, PLP2, SS; or

#12-24 x 0.354, FH100, PLP2, SS

E #6-32 x 1/4, PH, PLP, SS, Patchlock 3

Nuts

F #10-32, STL - Cage Nut; or

#10-32, UNF - Clip Nut

Use fasteners that pertain to your rack type.

Attach side brackets

QXS 48-Drive Rackmount Install Guide 4

Figure 1: 48-Drive Storage Chassis (bezel and disks are not installed)

Attach side brackets

Using a total of four #8-32 x 3/16 flathead Phillips screws (two per bracket), attach the side bracket to rear

mounting holes on each side of the chassis.

Figure 2: Attaching Side Brackets

1. Screw: Code A — P/N: 01-00000142

Rails Assembly

QXS 48-Drive Rackmount Install Guide 5

Rails Assembly

Note: The two rail kit installation pictorials immediately following show the left and right rails viewed

from the front and looking rearward. An assembly and an exploded view is provided for each rail.

Left Rail Assembly

Complete steps 1–3 to assemble the rails.

Note: Refer to callout 1 in Figure 3 below for the assembled left rail (ready for installation into the rack).

1. Slide the rear rail insert (callout 4, Figure 3 below) into the front rail sleeve (callout 2, Figure 3 below).

Figure 3: Left Rail Kit Components (assembly and exploded views)

1. Left rail assembly

2. Front rail sleeve

3. Rail shelf

4. Rear rail insert

5. Screw: Code B - P/N: 01-00000262-00-01

2. To determine the cabinet depth required by the rails, fit the rail assembly (callout 1) to the rack and note

which tapped holes in the rear rails align with the front rail’s slotted holes. If cage nuts are pre-installed,

remove them.

Rails Assembly

QXS 48-Drive Rackmount Install Guide 6

3. Using the measurements recorded in sub-step 2 above, select two or three #8-32 x 3/8 flathead Phillips

screws (depending on your cabinet depth) to loosely attach the rear rail insert (callout 4) to the front rail

sleeve (callout 2).

You will tighten the screws later.

Right Rail Assembly

Complete steps 1-3 above to assembly the right rail.

Figure 4: Right Rail Kit Components (assembly and exploded views)

1. Right rail assembly

2. Front rail sleeve

3. Rail shelf

4. Rear rail insert

5. Screw: Code B - P/N: 01-00000262-00-01

Install Rails (Square, Round, Pre-tapped Hole-Racks)

QXS 48-Drive Rackmount Install Guide 7

Install Rails (Square, Round, Pre-tapped

Hole-Racks)

This section provides the rail installation of three different types of racks. Information is as follows:

lSquare Hole-Rack Rail Installation below

lRound Hole-Rack Rail Installation on page 12

lPre-tapped Hole-Rack Rail Installation on page 16

Square Hole-Rack Rail Installation

Complete steps 1–4 to install the rails.

1. For square-hole racks, install cage nuts in the front rack holes where chassis ears will be attached.

a. Before rail installation, refer to Figure 5 below for location of screws and cage nuts for the front

of the chassis.

Figure 5: Screws and Cage Nuts for Chassis Front

1 2

1. Left Rail

2. Right Rail

3. Screws Installed into Threaded Holes in Rail

4. Cage Nut Installed (for chassis screws)

b. Before rail installation, refer to Figure 6 on the next page for location of screws and cage nuts for

the rear of the chassis.

Install Rails (Square, Round, Pre-tapped Hole-Racks)

QXS 48-Drive Rackmount Install Guide 8

Figure 6: Screws and Cage Nuts for Chassis Rear

1. Left Rail

2. Right Rail

3. Screws Installed into Cage Nut

4. Cage Nuts Installed in Rack

Note: If you insert the cage nuts incorrectly, use a Cage Nut Removal Tool to easily remove the

cage nuts from the rack holes.

Position the rail's front and back mounting flanges so that through holes align with corresponding rack

holes, and note the locations.

Note: Align the bottom of the rail with the bottom of the rack unit where you would like to install the

rails. Rails should not be installed where the rail will straddle rack units (U). Most racks provide

alignment markers indicating the rack units used for rail installation.

Attach two cage nuts at the front of the rack, and two at the rear, per the red "X" marks shown in the

following installation detail views (Figure 7 on the next page).

Note: The rail kit supports either the RAID (controller) or expansion chassis.

On the following diagram, elevation numbers are arbitrary and represent vertical location within the

rack.The 1U rack heights are shown next to cage nut installation locations.

Install Rails (Square, Round, Pre-tapped Hole-Racks)

QXS 48-Drive Rackmount Install Guide 9

Figure 7: Cage Nut Placement

1. Cage nut (Code F — P/N: 01-00000279-00-04

or 01-00000270-00-01)

2. Front View

3. Rear View

Note: Install the cage nuts at the same square hole elevations—two per column—on all four rack

posts.

Install Rails (Square, Round, Pre-tapped Hole-Racks)

QXS 48-Drive Rackmount Install Guide 10

2. For the square-hole racks, use two shoulder screws of the appropriate size (square-hole shoulder) to

attach the front of the rail assembly to the front of the rack.

Do so by attaching the screws through the two tapped holes on the front rail. See Figure 8 below.

Figure 8: Rail Attachment to Front of Rack (screws fastened to back of rack post - facing rearward)

1. Left rail with square holes

2. Right rail with square holes

3. Depending upon rack type, use two #10-32 x 3/4 truss Phillips screws or #12-24 x 3/8 Phillips screws or

appropriate metric (5 or 6 mm) pan head screws to attach the rear rail assembly to the rear of the rack.

See Figure 9 on the next page.

Use one of the following Code C screws (part numbers):

l01-00000264-00-01

l01-00000267-00-01

l01-00000269-00-01

l01-00000190

Note: While tightening the screws, push the rails outward to maximize the opening width.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Almacenamiento de Quantum

Quantum

Quantum DX100 Manual de usuario

Quantum

Quantum DLTtape DLT 4000 Manual de usuario

Quantum

Quantum DLTtape DLT 2000 Manual

Quantum

Quantum DLTtape SDLT 220 Hoja de información del producto

Quantum

Quantum Bigfoot 1.2AT Manual de usuario

Quantum

Quantum DLT-V4 Manual

Quantum

Quantum DXi4700 Manual de instalación y operación

Quantum

Quantum Scalar i500 Manual de usuario

Quantum

Quantum StorNext QD6000 Manual de usuario

Quantum

Quantum SuperLoader 3A Series Manual de usuario

Quantum

Quantum DXi8500 Manual de usuario

Quantum

Quantum DLT-V4 Manual de usuario

Quantum

Quantum DLT-S4 Manual de usuario

Quantum

Quantum Tape Drive SDLT 600A Manual de usuario

Quantum

Quantum Scalar i6000 Manual de usuario

Quantum

Quantum LTO 3 Manual de usuario

Quantum

Quantum FastStor 2 Manual de usuario

Quantum

Quantum Scalar 218 Guía de instalación

Quantum

Quantum Tape Drives A-Series Manual de usuario

Quantum

Quantum P1000 Series Manual de usuario

Quantum

Quantum ActiveScale P100E3 Instrucciones de instalación

Quantum

Quantum Scalar 50 Guía

Quantum

Quantum DLTtape DLT1 Manual de usuario

Quantum

Quantum F2000 Manual de usuario

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

HP StorageWorks MSL2024 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

HP P9000 Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario