PUTCO 85165 Manual de usuario

85165, 86165, 87165, 88165

87165L, 88165L

87165L-2, 88165L-2

2011+ FORD SD Bumper Grille Installation Instructions

Please read all instructions before installation and to check to see that all parts are included.

Bumper Grille Installation

1. Remove bumper grille from packaging. Check to see if all parts from above table are included.

2. Remove factory license plate by unhooking the bottom hooks first. Then squeeze the top two clips

to release the license plate from the bumper.

3. From under the vehicle, remove the three plastic clips that hold the rubber flap to the bumper.

Ensure you do not break the plastic clips as you will need them to reinstall the flap when finished.

This will allow for easier installation of the bumper grille later. Fold the flap out of the way. See

Figure 1.

KIT CONTENTS:

Description Qty.

Bumper Grille

Alcohol Wipe 1

Only for Lighted Grille (below)

Light Bar (Installed) 1 or 2

Wiring Harness 1

Switch 1

Light Bar Installation Instructions 1

Figure 1

Plasti lips removed

from bumper.

85165, 86165, 87165, 88165

87165L, 88165L

87165L-2, 88165L-2

4. Using the provided alcohol wipe, wipe down all areas that the bumper grille adheres to the Bumper.

Refer to Figure 2.

5. Insert the grille into the bumper starting with the bottom of the grille first. Refer to Figure 3 for

installation

Veiwed from front

Passenger Side of vehi le.

Figure 3

Figure 2

Clean area behind

bumper as shown.

85165, 86165, 87165, 88165

87165L, 88165L

87165L-2, 88165L-2

6. Rotate the grille upwards inserting the two tabs into the holes for the factory license plate. See

Figure 4.

7. Once the tabs are in the license plate holes, place the upper tabs behind the bumper while rolling

the grille into place. The final grille placement will look like Figure 5.

8. Remove the backing from the tape and from the backside of the grille press against the bumper grille

tabs to adhere them to the bumper. Apply firm pressure to all locations for 30 seconds.

9. Fold down tabs inserted into the license plate holes.

10. Reinstall license plate holder and reinsert the three plastic clips for the rubber flap.

11. Do not wash and avoid driving the vehicle for 12-24 hrs to allow the tape to fully adhere to the

bumper.

12. Continue onto wiring instructions if you purchased the lighted grille.

Figure 4

Figure 5

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios para automóviles de PUTCO

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario