Pulsar R1624T Manual de usuario

R1624T

v.1.0

R 24V/16x0,5A/TOPIC

RACK mounted power supply.

EN**

Edition: 1 from 22.09.2017

Supercedes the edition: ------------

www.pulsar.pl R1624T RACK POWER

Features:

DC 24V/16x0,5A uninterruptible power supply

for powering HD cameras (8A max.)

the adjustment of output voltage in the range

20V÷26V DC available from the front panel of

the power supply unit

16 outputs independently protected

by 0,5A melting fuses

high efficiency 82%

LED optical indication: AC, DC, TEMP, ALARM,

AUX1 ÷ AUX16

acoustic indication of failure

control of voltage presence at the

AUX1 ÷ AUX16 outputs

the ALARM technical output of collective failure

–relay type, activated by:

230V AC power loss

activation of the output fuse in the camera power

supply circuit

too high temperature of the PSU (>70°C)

the PSU failure

protections:

SCP short-circuit protection

OVP overvoltage protection

overvoltage protection

overload protection OLP

forced cooling (fan)

warranty –2 year from the production date

Sample application of the RACK power supply unit.

CONTENTS:

1. Technical description.

1.1. General description

1.2. Block diagram

1.3. Description of PSU components and connectors

1.4. Specifications

2. Installation.

2.1. Requirements

2.2. Installation procedure

3. Operating status indication.

3.1. LED indication

3.2. Technical output

3.3. Acoustic indication

4. Operation and use.

4.1. Overload or short circuit of the PSU output

4.2. Maintenance

www.pulsar.pl R1624T RACK POWER

1. Technical description.

1.1. General description.

The R1624Tpower supply unit is designed for uninterrupted power supply of up to 16 HD cameras requiring

stabilized voltage of 24V DC with the total current efficiency of 8A.The output voltage adjustment range is adjusted

via a potentiometer within the range of 20V÷26V DC. The PSU is fitted with 16 outputs protected independently

with melting fuse 0,5A. The power supply is fitted with the ALARM output of collective failure. In case of failure,

relay contacts are switched automatically, which is accompanied by acoustic and optical indication (the

corresponding led goes on). The power supply construction is based on the switch mode PSU with high energy

efficiency and is located in an enclosure adapted for mounting in standard RACK 19” cabinets.

1.2. Block diagram.

Fig.1. The block diagram of the PSU.

1.3. Description of PSU components and connectors.

Table 1. Components of the front panel of the power supply.

Element no.

[Fig. 2]

Description

AC OK –green LED, indicating the presence of 230V voltage

DC OK –green LED, indicating the presence of DC voltage

TEMP –red LED, indicating too high temperature of the power supply (>70°C)

Green LED AUX1 ÷ AUX16 –voltage indication at the outputs AUX

LED ALARM –red LED failure indication

AUX1 ÷ AUX16 –independently protected outputs

ALARM –technical output of collective failure –relay

Potentiometer, output voltage adjustment within the range of 20V÷26V DC

BUZZER, micro switch, turning ON / OFF of acoustic indication

switch in the top position, indication ON

switch in the down position, indication OFF

230V AC INPUT, power socket 230V AC, power cable 1,5m included

FMAINS,fuse in the supply circuit 230V AC, T 6,3A/250V

F1 ÷ F16, melting fuses in the camera power supply circuits AUX (+), F0,5A

www.pulsar.pl R1624T RACK POWER

Fig. 2. The front power of the power supply unit.

Fig.3. The view of the PSU.

www.pulsar.pl R1624T RACK POWER

1.4. Specifications.

- electrical parameters (tab.2)

- mechanical parameters (tab.3)

- operation safety (tab.4)

- operating parameters (tab.5)

Electrical parameters (tab. 2).

Mains supply

230V AC (-15%/+10%) 50Hz

Current up to

1A max./230V AC

Supply power

192W max.

Efficiency

82%

Output voltage

24V DC

Voltage adjustment range output

20÷26V DC

Output current

16 x 0,5A (I = 8A) max. @24V

Ripple

150 mV p-p max.

Short-circuit protection SCP

16 x F 0,5A melting fuse

Overload protection OLP

105% ÷ 150% of the PSU power, automatic return

Overvoltage protection OVP

29,5 ÷ 35V (PSU restart required)

Surge protection

varistors

Optical indication of operation:

LED: AC, DC, TEMP, ALARM, AUX1÷AUX16

Acoustic operation indication:

Piezoelectric indicator ~75dB/0,3m

The ALARM technical output of collective failure

Relay type: 1A@ 30VDC/50VAC

The FMAINS fuse in the 230V power supply circuit

T 6,3A

F1 ÷ F16, glass fuses in the cameras AUX (+)

power supply circuits

F 0,5A

Mechanical parameters (tab. 3).

Enclosure dimensions

W=19”, H=2U; 482 x 88 x 223 mm (WxHxD)

Fixation

four-point butt mounting to RACK profiles –the set include 4 M6 screws + cage nuts

Net weight

5,4kg / 5,9kg

Enclosure

Steel plate RAL 9005, black

Connectors

230V AC input: the IEC C14 socket with a fuse, power cable 1,5m

(included)

Outputs: BAT, ALARM, AUX1÷AUX16: Φ0,5-2,1 (AWG 24-12) 0,5-2mm2

Notes

Forced cooling (fan)

Operation safety (tab.4).

Protection class PN-EN 60950-1:2007

I (first)

Protection grade PN-EN 60529: 2002 (U)

IP20

Electrical strength of insulation:

- between input and output circuits of the PSU (I/P-O/P)

- between input circuit and PE protection circuit (I/P-FG)

- between output circuit and PE protection circuit (O/P-FG)

3000 V/AC min.

1500 V/AC min.

500 V/AC min.

Insulation resistance:

- between input circuit and output or protection circuit

100 MΩ, 500V/DC

Operating parameters (tab.5).

Environmental class

Operating temperature

-10ºC...+45ºC

Storage temperature

-20ºC...+60ºC

Relative humidity

20%...90%, without condensation

Vibrations during operation

unacceptable

Impulse waves during operation

unacceptable

Direct insulation

unacceptable

Vibrations and impulse waves during transport

According to PN-83/T-42106

www.pulsar.pl R1624T RACK POWER

2. Installation.

2.1. Requirements.

The PSU RACK shall be mounted by a qualified installer with appropriate permissions and qualifications for

230V/AC installations and low-voltage installations (required and necessary for a given country). The device shall

be mounted in confined spaces, according to the environment class II, with normal air humidity (RH=90% max.

without condensation) and the temperature from -10°C do +45°C.

During normal operation the total current consumption of the receivers cannot exceed I=8A.

As the PSU is designed for a continuous operation and is not equipped with a power-switch, therefore an

appropriate overload protection shall be guaranteed in the power supply circuit. Moreover, the user shall be

informed about the method of unplugging (usually through assigning an appropriate fuse in the fuse-box). The

electrical system shall follow valid standards and regulations.

2.2. Installation procedure.

1. Before installation, cut off the voltage in the 230V power-supply circuit.

2. Mount the power supply in a RACK 19" cabinet as shown below:

- Mount M6 cage nuts

- Secure the enclosure with 4xM6 screws

3. Connect the receivers’ cables to the terminals AUX1...AUX16.

4. If needed, the following technical connections can be made:

- ALARM –technical output of collective failure

5. Connect the ~230V AC power cord with the IEC C13 plug (included) to the 230V AC power supply and turn on the

power (~230V).

6. In the case of an unsafe voltage supply with frequent voltage drops in effective resistance of receiver supply cables

can occur, it is possible to adjust the output voltage using the potentiometer (20V÷26V DC) at the front panel of the power

supply.

7. Check the PSU operation indicator.

www.pulsar.pl R1624T RACK POWER

3. Operating status indication.

3.1. LED indication.

The PSU has 20 LED lights at the front panel:

GREEN LED:

on –the PSU is supplied with 230V AC

off –no 230V AC supply

GREEN LED:

on –DC voltage at the output of the switch mode PSU

off –no DC voltage at the output of the switch mode PSU

RED LED:

on –failure

off –no failure

RED LED:

ON –too high temperature of the switch mode power supply

(>70°C)

OFF –standard temperature of the switch mode power supply

GREEN LED:

on –DC voltage in the AUX1…AUX16 output

off –no DC voltage in the AUX1…AUX16 output

3.2. Technical output.

The power supply is fitted with the ALARM output of collective failure (relay type). A collective failure can

be triggered by the following events:

- 230V AC mains power failure

- Melting fuse activation F1÷F16

- Failure of the switch mode power supply

- Too high temperature of the switch mode power supply (>70°C)

Fig. 4. Electrical diagram of the ALARM collective output of failure.

CAUTION! In Fig. 4 the set of contacts shows a potential-free status of the relay, which

corresponds to power supply failure.

www.pulsar.pl R1624T RACK POWER

3.3. Acoustic indication.

A collective failure is indicated by the piezoelectric indicator, 1 beep every second. The acoustic indication

can be turned off by changing the ON / OFF position of the switch .

switch in the up position, indication ON

switch in the down position, indication OFF

4. Operation and use.

4.1. Overload or short circuit of the PSU output.

The AUX1 ÷ AUX16 power supply outputs are protected against short circuit by melting fuses; in the case

of fuse failure, it should be replaced with a fuse of the same type.

4.2. Maintenance.

Any and all maintenance operations may be performed following the disconnection of the PSU from the

power supply network. The PSU does not require performing any specific maintenance measures. In case of fuse

replacement, use a replacement of the same parameters.

WEEE LABEL

Waste electrical and electronic equipment must not be disposed of with normal household

waste. According to the European Union WEEE Directive, waste electrical and electronic

equipment should be disposed of separately from normal household waste.

Pulsar

Siedlec 150, 32-744 Łapczyca, Poland

Tel. (+48) 14-610-19-40, Fax. (+48) 14-610-19-50

E-mail: biuro@pulsar.pl, sales@pulsar.pl

http:// www.pulsar.pl, www.zasilacze.pl

Tabla de contenidos

Otros manuales de Fuente de alimentación de Pulsar

Pulsar

Pulsar PSUPS20A12E Manual de usuario

Pulsar

Pulsar PS-12V5A Manual de usuario

Pulsar

Pulsar PSBOC1001270 Manual de usuario

Pulsar

Pulsar PSC12010 Manual de usuario

Pulsar

Pulsar PSBD 5012 Manual de usuario

Pulsar

Pulsar MS 1012 Manual de usuario

Pulsar

Pulsar MSRD-13,8V/2,5A Manual de usuario

Pulsar

Pulsar PSACH 01246 Manual de usuario

Pulsar

Pulsar PS701205 Manual de usuario

Pulsar

Pulsar PSCL12020 Manual de usuario

Pulsar

Pulsar PS-602425 Manual de usuario

Pulsar

Pulsar DSO-PRA Manual de usuario

Pulsar

Pulsar HPSDCG2 Series Manual de usuario

Pulsar

Pulsar R812P Manual de usuario

Pulsar

Pulsar AWO003PU Manual de usuario

Pulsar

Pulsar PS401230 Manual de usuario

Pulsar

Pulsar PSCLB13830 Manual de usuario

Pulsar

Pulsar PSZKT5A Manual de usuario

Pulsar

Pulsar PSCL12015 Manual de usuario

Pulsar

Pulsar PSBEN 3012C Manual de usuario

Pulsar

Pulsar HPSDCSEP-12V4x1A Manual de usuario

Pulsar

Pulsar PSD15040 Manual de usuario

Pulsar

Pulsar RUPS812T Manual de usuario

Pulsar

Pulsar PSAC 04244SEP Manual de usuario

Manuales populares de Fuente de alimentación de otras marcas

Monacor

Monacor PS-12CCD Manual de usuario

VOLTIMA

VOLTIMA MagicBox 15 Manual de usuario

Agilent Technologies

Agilent Technologies 6032A Manual de usuario

Miller

Miller Auto Deltaweld 452 Manual de usuario

BCP

BCP PUOUBK Hoja de instrucciones

HC 2210 Manual de usuario

Puls

Puls CT5.241 Manual de usuario

OCZ

OCZ ZX1250W Manual de usuario

iseg

iseg ECH 238 Manual de usuario

Power

Power XXL A Series Manual de usuario

Agilent Technologies

Agilent Technologies 6631B Manual de usuario

Renogy

Renogy PHOENIX 300 Manual de usuario

HP 6200B Manual de servicio

Epson

Epson Stylus Scan 2500 Manual de funcionamiento

Puls

Puls MiniLine ML50.100 Manual de usuario

Puls

Puls AS-Interface SLA4.100 Manual de usuario

Kenwood

Kenwood PS-60 Manual de usuario

Elmdene

Elmdene G1380xN-y-s Series Manual de usuario