Protech SE-8134 Manual de usuario

USER

MANUAL

SE-8134

Intel®AtomTM x7/ Celeron®

Processor Slim and

Fanless Embedded PC

SE-8134 M2

(SE-8134) Intel®AtomTM x7/

Celeron®Processor Slim and

Fanless Embedded PC

All trademarks and registered trademarks mentioned herein are the

property of their respective owners.

This manual is copyrighted in Apr. 2023. You may not reproduce

or transmit in any form or by any means, electronic, or

mechanical, including photocopying and recording.

DISCLAIMER

This user’s manual is meant to assist users in installing and setting up

the system. The information contained in this document is subject to

change without any notice.

CE NOTICE

This is a class A product. In a domestic environment this product may

cause radio interference in which case the user may be required to take

adequate measures.

FCC NOTICE

This equipment has been tested and found to comply with the limits for

a Class A digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

You are cautioned that any change or modifications to the equipment

not expressly approve by the party responsible for compliance could

void your authority to operate such equipment.

CAUTION: Danger of explosion may occur when the battery

is incorrectly replaced. Replace the battery only with the

same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer’s

instructions.

WARNING: Some internal parts of the system may have

high electrical voltage. We strongly recommend that only

qualified engineers are allowed to service and disassemble

the system. If any damages should occur on the system and

are caused by unauthorized servicing, it will not be covered

by the product warranty.

Contents

Revision History ............................................................................................. v

1Introduction .........................................................................................1-1

1.1 About This Manual ....................................................................1-2

2Getting Started....................................................................................2-1

2.1 Package List..............................................................................2-2

2.2 System Overview ......................................................................2-3

2.2.1 Front View .........................................................................2-3

2.2.2 Rear View..........................................................................2-3

2.2.3 Top View............................................................................2-3

2.2.4 Side View...........................................................................2-4

2.2.5 Quarter View......................................................................2-4

2.3 System Specifications...............................................................2-5

2.4 Safety Precautions....................................................................2-7

3System Configuration.........................................................................3-1

3.1 JUMPER & CONNECTOR QUICK REFERENCE TABLE........3-2

3.2 COMPONENT LOCATIONS OF SYSTEM MAIN BOARD .......3-3

3.2.1 Top View of System Main Board .......................................3-3

3.2.2 Bottom View of System Main Board..................................3-5

3.3 HOW TO SET JUMPERS .........................................................3-6

3.4 Setting Main Board Connectors and Jumpers..........................3-8

3.4.1 COM Connector.................................................................3-8

3.4.2 COM1 and COM2 PIN9 Definition Selection Guide........3-10

3.4.3 Power Input Connector....................................................3-11

3.4.4 Power Button Connector .................................................3-11

3.4.5 LAN1, LAN2 Ports...........................................................3-12

3.4.6 Dual USB 3.0 Connectors ...............................................3-14

3.4.7 USB 3.0 Connectors........................................................3-15

3.4.8 Digital Input/Output Connector........................................3-16

3.4.9 I2C Wafer.........................................................................3-17

3.4.10 I2C PIN2 Voltage Selection.............................................3-18

3.4.11 DVI Port...........................................................................3-19

3.4.12 HDMI Port Connector......................................................3-20

3.4.13 HDMI Audio Connector....................................................3-21

3.4.14 Low Pin Count (LPC) Connector.....................................3-22

3.4.15 Power over Ethernet (PoE) Connector............................3-22

3.4.16 HDMI2 SELECTION........................................................3-23

3.4.17 MINI PCI EXPRESS SLOT .............................................3-24

3.4.18 Mini- Serial ATA (SATA) SLOT.........................................3-25

3.4.19 Serial ATA (SATA) 3.0 Connector ....................................3-26

3.4.20 HDD Power Connector....................................................3-26

3.4.21 AT / ATX Mode Selection.................................................3-27

3.4.22 TPM Module Selection ....................................................3-27

3.4.23 CLEAR CMOS DATA SELECTION .................................3-28

4Software Utilities.................................................................................4-1

4.1 Introduction................................................................................4-2

4.2 Installing Intel®Chipset Software Installation Utility..................4-3

4.2.1 Introduction........................................................................4-3

4.2.2 Intel®Chipset Software Installation Utility .........................4-3

4.3 INTEL®TRUSTED EXECUTION ENGINE DRIVER

INSTALLATION .........................................................................4-4

iii

4.3.1 Introduction........................................................................4-4

4.3.2 Installation Instructions for Windows 10............................4-4

4.4 Intel®Patch Driver installation...................................................4-5

4.4.1 Introduction........................................................................4-5

4.4.2 Installation Instructions for Windows 10............................4-5

4.5 Installing Graphics Driver Utility................................................4-6

4.6 Installing LAN Driver Utility........................................................4-7

4.7 Installing Sound Driver Utility....................................................4-8

4.8 Installing Intel®Serial I/O Driver Utility......................................4-9

5BIOS SETUP ........................................................................................5-1

5.1 Introduction................................................................................5-2

5.2 Accessing Setup Utility..............................................................5-4

5.3 Main...........................................................................................5-7

5.4 Advanced ..................................................................................5-9

5.4.1 Advanced - ACPI Settings...............................................5-10

5.4.2 Advanced –Hardware Monitor........................................5-11

5.4.3 Advanced –F81946 Watchdog Configuration.................5-12

5.4.4 Advanced –CPU Configuration ......................................5-13

5.4.4.1 Advanced - CPU Configuration - Socket 0 CPU

Information…...................................................................5-14

5.4.4.2 Advanced - CPU Configuration - CPU Power

Management…................................................................5-16

5.4.5 Advanced - F81946 Super IO Configuration...................5-17

5.4.6 Advanced –Network Stack Configuration.......................5-22

5.4.7 Advanced - USB Configuration .......................................5-23

5.4.8 Advanced - Platform Trust Technology............................5-24

5.5 Chipset....................................................................................5-25

5.5.1 Chipset –North Bridge.....................................................5-26

5.5.2 Chipset –South Bridge ....................................................5-27

5.5.2.1 Chipset –South Bridge- HD-Audio Configuration............5-28

5.5.2.2 Chipset –South Bridge- LPSS Configuration ..................5-29

5.5.2.3 Chipset –South Bridge- PCI Express Configuration........5-30

5.5.2.4 Chipset –South Bridge- SATA Drives ..............................5-35

5.5.2.5 Chipset –South Bridge- Miscellaneous Configuration.....5-36

5.6 Security ...................................................................................5-37

5.7 Boot.........................................................................................5-39

5.8 Save & Exit..............................................................................5-41

Appendix A System Diagrams....................................................... 1

SE-8134 Bottom Cover Exploded Diagram......................................................2

Heat Sink Exploded Diagram .............................................................................3

Front & Rear I/O Panel Installation Exploded Diagram ..................................4

Mother Board Exploded Diagram.......................................................................5

HDD Module Exploded Diagram........................................................................6

Packing Exploded Diagram.................................................................................7

Appendix B Technical Summary................................................... 1

System Block Diagram ........................................................................................2

Interrupt Map.........................................................................................................3

I/O MAP ...............................................................................................................18

Memory Map.......................................................................................................20

Configuring WatchDog Timer............................................................................22

Flash BIOS Update............................................................................................25

Revision History

The revision history of SE-8134 User Manual is described below:

Version No. Revision History Page No. Date

Revised the picture of System Main

Board.

3-3

2023/04/07

Corrected DIO1 connector pictures. 3-16

M1 Initial Release 2017/07

SE-8134 SERIES USER MANUAL

Page: 1-1

1 Introduction

This chapter provides the introduction for the SE-8134

system as well as the framework of the user manual.

The following topic is included:

•About This Manual

Chapter 1 Introduction

SE-8134 SERIES USER MANUAL

Page: 1-2

1.1 About This Manual

Thank you for purchasing our SE-8134 system. The SE-8134 is an updated system

designed to be comparable with the highest performance of IBM AT personal

computers. The SE-8134 provides faster processing speed, greater expandability and

can handle more tasks than before. This manual is designed to assist you how to

install and set up the whole system. It contains 5 chapters and 2 appendixes. Users can

configure the system according to their own needs. This user manual is intended for

service personnel with strong hardware background. It is not intended for general

users.

The following section describes the structure of this user manual.

Chapter 1 Introduction

This chapter introduces the framework of this user manual.

Chapter 2 Getting Started

This chapter describes the package contents and system specifications, and illustrates

the physical appearances for the SE-8134 system. Read the safety reminders carefully

on how to take care of your system properly.

Chapter 3 System Configuration

This chapter describes the locations and functions of the system motherboard

components. You will learn how to properly configure the connectors and system

configuration jumpers on the motherboard and configure the system to meet your own

needs.

Chapter 4 Software Utilities

This chapter introduces how to install Intel Chipset Software Installation Utility, Intel

Management Engine Components Installer Driver Utility, Intel USB 3.0 Extensible

Host Controller Driver Utility, RAID Driver Utility (optional, only for Q170 SKU),

Graphics Driver Utility, LAN Driver Utility and Sound Driver Utility.

Chapter 5 AMI BIOS Setup

This chapter provides BIOS setup information.

Appendix A System AssemblyDiagrams

This appendix provides the exploded diagrams and part numbers of the SE-8134.

Appendix B Technical Summary

This appendix provides the information about the system block diagram, allocation

maps for system resources, Watchdog Timer Configuration and Flash BIOS Update.

Tabla de contenidos

Otros manuales de Hardware de computadora de protech

protech

protech prox BC-K201 Manual de usuario

protech

protech EB-471 Manual de usuario

protech

protech SE-8300 Manual de usuario

protech

protech ProX-1695 Manual de usuario

protech

protech ProX-1580 Manual de usuario

protech

protech ProX-1550 Manual de usuario

protech

protech Prox SE-8124 Manual de usuario

protech

protech Prox-1510 M1 Manual de usuario

protech

protech BM-0972 Manual de usuario

protech

protech BM-0982 Manual de usuario

protech

protech BE-0961 Manual de usuario

protech

protech Celeron EB-471LF M1 Manual de usuario

protech

protech PC-550 Manual de usuario

protech

protech ProX-1635LF Manual de usuario

protech

protech ProX-1688 Manual de usuario

protech

protech PC-420 Manual de usuario

protech

protech BE-0996 Manual de usuario

protech

protech ProX-1680 Manual de usuario

protech

protech Prox SG-S152 Manual de usuario

protech

protech PC-560-G5 Manual de usuario

protech

protech BE-0986 Manual de usuario

protech

protech ProX-1640 Manual de usuario

protech

protech ProX-1215 Manual de usuario

protech

protech ProX-1690 Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

protech SE-8134 Manual de usuario

Manuales populares de Hardware de computadora de otras marcas