Prorack K797 Manual de usuario
K797
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 1 x 1 x 1 x 1
x 1 x 1 x 1 x 1
x 1 x 1 x 1 x 1
Revision No: 2B 1
Fitting Kit K797
MAX kgs (lbs)
W/P WHD
Lexus
IS 200, 4dr Sedan 15-+ AU 60 kgs (132 lbs) 60 kgs (132 lbs)
IS 200, 4dr Sedan 15-+ NZ 60 kgs (132 lbs) 60 kgs (132 lbs)
IS 200, 4dr Sedan 15-+ EU 60 kgs (132 lbs) 60 kgs (132 lbs)
IS 200, 4dr Sedan 15-+ ZA 60 kgs (132 lbs) 60 kgs (132 lbs)
IS 250, 4dr Sedan 13-+ NZ 60 kgs (132 lbs)
IS 250, 4dr Sedan 13-+ AU 60 kgs (132 lbs)
IS 250, 4dr Sedan 13-+ EU 60 kgs (132 lbs)
IS 250, 4dr Sedan 13-+ CN 60 kgs (132 lbs)
IS 300H, 4dr Sedan 13-+ NZ 60 kgs (132 lbs)
IS 300H, 4dr Sedan 13-+ AU 60 kgs (132 lbs)
IS 300H, 4dr Sedan 13-+ EU 60 kgs (132 lbs)
IS 350, 4dr Sedan 13-+ NZ 60 kgs (132 lbs)
IS 350, 4dr Sedan 13-+ AU 60 kgs (132 lbs)
IS 350, 4dr Sedan 13-+ ZA 60 kgs (132 lbs)
IS, 4dr Sedan 14-+ US 60 kgs (132 lbs)
2
Fitting Kit K797
X
A B C 1 2 3
IS 200, 4dr Sedan 15-+ (AU) -350mm 420mm - 810mm 800mm -
-13 -3/4ths" 16 9/16ths" - 31 7/8ths" 31 1/2ths" -
IS 200, 4dr Sedan 15-+ (NZ) -350mm 420mm - 810mm 800mm -
-13 -3/4ths" 16 9/16ths" - 31 7/8ths" 31 1/2ths" -
IS 200, 4dr Sedan 15-+ (EU) -350mm 420mm - 810mm 800mm -
-13 -3/4ths" 16 9/16ths" - 31 7/8ths" 31 1/2ths" -
IS 200, 4dr Sedan 15-+ (ZA) -350mm 420mm - 810mm 800mm -
-13 -3/4ths" 16 9/16ths" - 31 7/8ths" 31 1/2ths" -
IS 250, 4dr Sedan 13-+ (NZ) -350mm 420mm - 810mm 800mm -
-13 -3/4ths" 16 9/16ths" - 31 7/8ths" 31 1/2ths" -
IS 250, 4dr Sedan 13-+ (AU) -350mm 420mm - 810mm 800mm -
-13 -3/4ths" 16 9/16ths" - 31 7/8ths" 31 1/2ths" -
IS 250, 4dr Sedan 13-+ (EU) -350mm 420mm - 810mm 800mm -
-13 -3/4ths" 16 9/16ths" - 31 7/8ths" 31 1/2ths" -
IS 250, 4dr Sedan 13-+ (CN) -350mm 420mm - 810mm 800mm -
-13 -3/4ths" 16 9/16ths" - 31 7/8ths" 31 1/2ths" -
IS 300H, 4dr Sedan 13-+ (NZ) -350mm 420mm - 810mm 800mm -
-13 -3/4ths" 16 9/16ths" - 31 7/8ths" 31 1/2ths" -
IS 300H, 4dr Sedan 13-+ (AU) -350mm 420mm - 810mm 800mm -
-13 -3/4ths" 16 9/16ths" - 31 7/8ths" 31 1/2ths" -
IS 300H, 4dr Sedan 13-+ (EU) -350mm 420mm - 810mm 800mm -
-13 -3/4ths" 16 9/16ths" - 31 7/8ths" 31 1/2ths" -
IS 350, 4dr Sedan 13-+ (NZ) -350mm 420mm - 810mm 800mm -
-13 -3/4ths" 16 9/16ths" - 31 7/8ths" 31 1/2ths" -
IS 350, 4dr Sedan 13-+ (AU) -350mm 420mm - 810mm 800mm -
-13 -3/4ths" 16 9/16ths" - 31 7/8ths" 31 1/2ths" -
IS 350, 4dr Sedan 13-+ (ZA) -350mm 420mm - 810mm 800mm -
-13 -3/4ths" 16 9/16ths" - 31 7/8ths" 31 1/2ths" -
IS, 4dr Sedan 14-+ (US) -350mm 420mm - 810mm 800mm -
-13 -3/4ths" 16 9/16ths" - 31 7/8ths" 31 1/2ths" -
3
Fitting Kit EN
K797
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4
Fitting Kit EN
K797
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5
Fitting Kit EN
K797
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = A314
B = A315
C = A316
D = A317
6
Fitting Kit EN
K797
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Refer to the underside of the pad for the
part number.
7
Fitting Kit EN
K797
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 261A
B = 262A
C = 295A
D = 296A
●Place rubber pads (supplied with fitting kit)
on the vehicle roof. Pad may vary in shape
to that shown.
●Make sure the pad fits into the holes
underneath the foot.
8
Fitting Kit EN
K797
Fitment
●Clamps directly to edge of roof under the
doors
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Tighten adjusting screw to 2 Nm (1.5 ft lb)
hand tight.
9
Fitting Kit EN
K797
●Tighten locking screw on both legs evenly,
2.5 Nm (1.8 ft lb).
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
10
Tabla de contenidos
Otros manuales de Accesorios para automóviles de Prorack
Prorack
Prorack K464 Manual de usuario
Prorack
Prorack WHISPBAR S45 Manual de operación e instalación
Prorack
Prorack K444 Manual de operación e instalación
Prorack
Prorack K146 Manual de usuario
Prorack
Prorack K367 Manual de operación e instalación
Prorack
Prorack K084 Manual de usuario
Prorack
Prorack K876 Manual de usuario
Prorack
Prorack K306 Manual de usuario
Prorack
Prorack K496 Manual de operación e instalación
Prorack
Prorack K604 Manual de usuario
Prorack
Prorack K596 Manual de usuario
Prorack
Prorack PR3217 Manual de usuario
Prorack
Prorack K144W Manual de operación e instalación
Prorack
Prorack K010 Manual de usuario
Prorack
Prorack K629 Manual de usuario
Prorack
Prorack K1208 Manual de usuario
Prorack
Prorack K704 Manual de usuario
Prorack
Prorack K312 Manual de usuario
Prorack
Prorack K903 Manual de usuario
Prorack
Prorack PR3205 Manual de usuario
