Prorack K018 Manual de usuario
K018
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 1 x 4 x 4
Revision No: 5E 1
Fitting Kit K018
MAX kgs (lbs)
W/P WHD
Isuzu
Aska CX, 4dr Sedan 90-93 EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Subaru
Legacy, 4dr Sedan 89-93 EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Legacy, 4dr Sedan 89-93 ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
Legacy, 4dr Sedan 94-98 ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
Legacy, 4dr Sedan 94-98 EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Legacy, 4dr Sedan 95-99 US 75 kgs (165 lbs) 75 kgs (165 lbs)
Legacy, 4dr Sedan Jun 94-Nov 98 NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
Legacy, 4dr Sedan Oct 89-May 94 NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
Leone, 4dr Sedan 84-94 AU 75 kgs (165 lbs) 75 kgs (165 lbs)
Leone, 4dr Sedan 85-Oct 93 NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
Leone, 4dr Sedan Jun 84-94 AU 75 kgs (165 lbs) 75 kgs (165 lbs)
Liberty, 4dr Sedan Jun 94-Jan 99 AU 75 kgs (165 lbs) 75 kgs (165 lbs)
Liberty, 4dr Sedan Oct 89-May 94 AU 75 kgs (165 lbs) 75 kgs (165 lbs)
Omega, 3dr Coupe Aug 78-94 NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
Omega, 4dr Sedan Dec 84-94 NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
2
Fitting Kit EN
K018
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
3
Fitting Kit EN
K018
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
4
Fitting Kit EN
K018
●Remove locking screw.
●Cut protective strip in four equal lengths.
●Apply protective strip as shown.
Trim if required.
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
5
Fitting Kit EN
K018
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Fit rubber pads (supplied with fitting kit) to
foot.
●Make sure the pad fits into the holes
underneath the foot.
6
Fitting Kit EN
K018
Fitment
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
7
Fitting Kit EN
K018
●Tighten locking screw on both legs evenly.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
8
Fitting Kit EN
K018
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
9
Fitting Kit EN
K018
Maintenance
●Clean the car roof and surfaces of the
product that will be in contact with the car
roof.
●Follow the fitting instructions for fitting the
product to your vehicle. Make sure all steps
are carried out in order.
●Set crossbars a minimum distance of
700mm (27 1/2") apart where no other
distance is specified in the fitting
instructions. This is especially important
when carrying long loads.
●Check unit is securely attached whenever
you refit it to the vehicle. If the unit feels
loose, refer to the fitting instructions and
readjust.
●Some glass/panoramic roofs and radio
antennae may not be able to be used when
the product is fitted.
●Do not modify this product.
●Refer to the maximum permitted load
capacity specified in the fitting instructions.
Do not exceed the vehicle manufacturers
roof load rating if it is lower than the
maximum load capacity specified in the
fitting instructions.
●Loads should not overhang the sides of the
product and be evenly distributed with the
lowest possible centre of gravity.
●Long loads should be secured with non-
elastic straps to the front and rear of the
vehicle.
●Objects with pointed ends (e.g. ski poles)
should be carried with the pointed ends to
the rear of the vehicle.
●Remove all loose or removable objects
from the load prior to loading.
●Make sure all loads are securely fastened
with non-elastic straps. Check regularly
during longer journeys.
●A loaded roof rack system can alter the
performance of your vehicle. Be especially
aware of the effects of side winds,
changing of direction, and braking
performance. Avoid rapid acceleration and
deceleration. Drive carefully.
●Note that the total height of the vehicle
increases when upright loads are carried.
●Products should be locked during transport
if they have locks fitted.
10
Tabla de contenidos
Otros manuales de Accesorios para automóviles de Prorack
Prorack
Prorack K107 Manual de usuario
Prorack
Prorack K528 Manual de usuario
Prorack
Prorack K327 Manual de usuario
Prorack
Prorack K507 Manual de usuario
Prorack
Prorack K334 Manual de usuario
Prorack
Prorack K573 Manual de usuario
Prorack
Prorack K130 Manual de usuario
Prorack
Prorack K701 Manual de usuario
Prorack
Prorack K869 Manual de usuario
Prorack
Prorack K372 Manual de operación e instalación
Prorack
Prorack K144W Manual de operación e instalación
Prorack
Prorack K619 Manual de usuario
Prorack
Prorack K1226 Manual de usuario
Prorack
Prorack K894 Manual de usuario
Prorack
Prorack K398 Manual de usuario
Prorack
Prorack K199 Manual de usuario
Prorack
Prorack K589 Manual de usuario
Prorack
Prorack K310 Manual de usuario
Prorack
Prorack WHISPBAR S53 Manual de operación e instalación
Prorack
Prorack K1153 Manual de usuario
