PROPOINT 8819864 Manual de usuario
V1.0 8819864
Please read and understand all instructions before use. Retain this manual
for future reference.
SOLAR AUTO-DARKENING
WELDING HELMET WITH
BLUE LENS TECHNOLOGY
USER MANUAL
8819864 Solar Auto-Darkening Welding Helmet V1.0
With Blue Lens Technology
2 For technical questions call 1-800-665-8685
SPECIFICATIONS
Viewing Area 3.94 X 3.28 in. (100 x 83 mm)
Light State Shade DIN 4
Variable Shade DIN 5 to 9 / 9 to 13
Reaction Time 1/25,000 seconds (0.04 milliseconds)
Delay Control (Dark to Light)
0.1 to 0.9 Seconds (Adjustable)
Sensitivity Low to High (Adjustable)
UV/IR Protection Up to Shade DIN 15 at all times.
Arc Sensors
4
Power ON/OFF Fully Automatic
Power Supply Solar cells and replaceable CR2450 lithium
batteries
Battery Life 1,000 h
Grind Mode
Yes
Operating Temperature 14° ~ 149°F (-10° to 65°C)
Storage Temperature -4° ~ 185°F (-20° to 85°C)
Compliance ANSI Z87 W4/5-13 and CSA Z94.3 W4/5-13
ADF Controls Internal - Digital
Material Polyamide
Headgear Adjustable Ratcheting Type
Memory function
Yes
SOLAR AUTO-DARKENING
WELDING HELMET WITH
BLUE LENS TECHNOLOGY
V1.0 Solar Auto-Darkening Welding Helmet 8819864
With Blue Lens Technology
Visit www.princessauto.com for more information 3
INTRODUCTION
The Solar Auto-Darkening Welding Helmet incorporates Blue
Lens technology, letting the welder to see the full colour
spectrum with clarity while in the light state. Digital controls
enables the welder to adjust the DIN shade number,
Weld/Grind selection, plus the delay and sensitivity timing. The
user can save the settings in memory up to three times.
SAFETY
WARNING! Read and understand all instructions before using
this tool. The operator must follow basic precautions to reduce
the risk of personal injury and/or damage to the equipment.
Keep this manual for safety warnings, precautions, operating or
inspection and maintenance instructions.
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this
manual. A notice is an alert that there is a possibility of property
damage, injury or death if certain instructions are not followed.
DANGER! This notice indicates an immediate and specific
hazard that will result in severe personal injury or
death if the proper precautions are not taken.
WARNING! This notice indicates a specific hazard or unsafe
practice that could result in severe personal injury
or death if the proper precautions are not taken.
CAUTION! This notice indicates a potentially hazardous
situation that may result in minor or moderate
injury if proper practices are not taken.
NOTICE! This notice indicates that a specific hazard or unsafe
practice will result in equipment or property
damage, but not personal injury.
8819864 Solar Auto-Darkening Welding Helmet V1.0
With Blue Lens Technology
4 For technical questions call 1-800-665-8685
WORK AREA
1. Operate in a safe work environment. Keep your work area
clean, well lit and free of distractions.
2. Keep anyone not wearing the appropriate safety equipment
away from the work area.
3. Store tools properly in a safe and dry location. Keep tools out
of the reach of children.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved by
the Canadian Standards Association (CSA) or American
National Standards Institute (ANSI).
1. Always wear impact safety goggles that provide front and
side protection for the eyes.
2. Wear gloves that provide protection based on the work
materials or to reduce the effects of tool vibration.
3. Wear protective clothing designed for the work environment
and tool.
4. Control the tool, personal movement and the work
environment to avoid personal injury or damage to tool.
5. Do not operate any tool when tired or under the influence of
drugs, alcohol or medications.
6. Use the correct tool for the job. This welding helmet was
designed for a specific function. Do not modify or alter this
welding helmet or use it for an unintended purpose.
SPECIFIC SAFETY PRECAUTIONS
WARNING! The Auto-Darkening Welding Helmet does not
protect against severe impact hazards, explosions or corrosive
liquids. Machine guards or eye splash protection must be used
when these hazards are present.
V1.0 Solar Auto-Darkening Welding Helmet 8819864
With Blue Lens Technology
Visit www.princessauto.com for more information 5
WARNING! Using filter forms from any other manufacturer’s
helmet can seriously impaired the protection provided and may
result in serious personal injury.
1. Use the correct tool for the job. This tool was designed for a
specific function. Do not modify or alter this tool or use it for
an unintended purpose.
2. This auto-darkening welding helmet is not recommended
for overhead welding applications, laser welding or laser
cutting applications.
3. This welding helmet is not suitable to laser welding and oxy-
acetylene welding.
4. In the event of electronic failure, the filter remains dark at
Shade 15 to protect against UV and IR radiation.
5. Use the auto-darkening welding filter with inner and outer
cover lenses. Never open or tamper with the filter cartridge.
6. Ensure the front cover lens is mounted before use. Remove
the protective film.
7. Ensure that the lens is clean and there is no dirt or spatter
covering the four sensors at the front of the filter cartridge.
8. Inspect all parts for signs of wear or damage. Any scratched
or cracked parts should be replaced prior to use.
9. Never place the helmet on a hot surface.
10. Arc rays can burn both eyes and skin. Arc welding produces
intense visible and invisible (ultraviolet and infrared) rays.
Wear a welding helmet fitted with the proper shade to
protect your face and eyes when welding or watching.
11. Check whether welding or grinding mode is chosen
before use.
12. The reaction of the filter’s liquid crystal will be slower if
the ambient temperature is low, but it will not affect
protective functions.
8819864 Solar Auto-Darkening Welding Helmet V1.0
With Blue Lens Technology
6 For technical questions call 1-800-665-8685
13. Replace the protective lenses immediately if broken or
scratched. The damage will obscure vision and reduce the
filter’s protective performance.
UNPACKING
WARNING! Do not operate the tool if any part is missing.
Replace the missing part before operating. Failure to do so
could result in a malfunction and personal injury.
Remove the parts and accessories from the packaging and inspect
for damage. Make sure that all items in the contents are included.
Contents: • Welding Helmet Shell • Internal and External Lenses
• Cartridge Filter • Headgear • Batteries
V1.0 Solar Auto-Darkening Welding Helmet 8819864
With Blue Lens Technology
Visit www.princessauto.com for more information 7
IDENTIFICATION KEY
A Shade Button
B Sensitivity Button
C Weld/Grind Button
D Delay Button
E LCD Screen
F Memory Buttons
G Battery Icon
H Welding Icon
I Grinding Icon
J Sensitivity Range Icon
K Shade DIN Number
L Delay Range Icon
M to O Chosen Memory Slot
P Shade Range 9-13 Selected
Q Shade Range 5-9 Selected
8819864 Solar Auto-Darkening Welding Helmet V1.0
With Blue Lens Technology
8 For technical questions call 1-800-665-8685
ASSEMB LY
The welding helmet is preassembled. Remove the protective film
from both lenses before use.
ADJUST THE WELDING HELMET FIT
The headband should be adjusted both in diameter and height.
The angle between face and helmet should also be adjusted
(recommended 10° to 12°).
1. Adjust the headband diameter with the adjusting knob (#14) on
the headband. Twist clockwise to tighten and counterclockwise
to loosen.
2. Adjust the headband height by releasing the segmental
positioning plate (#18) and changing the top strap hole.
3. Adjust the helmet position on the headband. There are three
slots on the headgear slider (#12). Once the slot is chosen,
tighten the angle adjustment knobs. Make sure the same slot
is chosen for both sides for proper vision.
4. Adjust the helmet to get the desired viewing angle. Once the
angle is correct, tighten the two angle adjustment knobs (#2)
connecting the headband to the helmet shell until snug. The
helmet should still swing up, but it should not drift downward
when in place for welding.
OPERATION
BEFORE WELDING
1. Ensure that the internal and external protective films are
removed from the lenses.
2. Check that the batteries have sufficient power to operate
the helmet.
3. Check that the arc sensors are clean and not blocked by dust
or debris.
4. Check for head band tightness before each use.
V1.0 Solar Auto-Darkening Welding Helmet 8819864
With Blue Lens Technology
Visit www.princessauto.com for more information 9
HELMET SETTINGS
The LCD displays the activity icons and the words Sensitivity,
Shade and Delay at the bottom, along with their accompanying
range icons indicating the selected setting.
Each setting is entered by first pressing a button twice to
activate the selection, then continuing to press the same
button to change the setting number. There are four control
buttons and three memory select buttons.
SHADE NUMBER SELECTION
Activating the shade button (A) will display either the 5-9 (Q)
or 9-13 (P) shade range icon. It will start at the lowest setting.
Each time you press the shade button, the number displayed
(K) will increase by one.
Press the weld/grind button (C) to switch over to the 9-13 range
and press the shade button. Continually pressing it past shade 13
will automatically switch it back to the 5-9 shade range.
Adjust the welding helmet’s Shade Number to match the type
of welding. Consult the Welding Shade Guide (see Appendix A)
to determine the minimum shade for the amperage and
welding method being employed.
DELAY TIME
Delay time refers to the time the cartridge filter is set to
change from the dark to bright state after welding stops. The
delay can be adjusted (L) up to a 0.9 second delay.
The delay is set between 0.1, suitable for spot or short welds to
0.9 seconds, suitable for heavy current welding or when visible
light is produced.
Press the delay button (D) after activation to add a bar to the
Delay LCD range. Each bar increases the delay by 0.2 seconds
starting from 0.1 to 0.9 seconds.
8819864 Solar Auto-Darkening Welding Helmet V1.0
With Blue Lens Technology
10 For technical questions call 1-800-665-8685
SENSITIVITY
Press the sensitivity button (B) twice to activate the selection.
The top sensitivity bar will flash to indicate the highest sensitivity
is selected. Continue to press the sensitivity button to scroll
through settings 1 to 5 (least to most sensitive).
1. Low Setting - suitable for high amperage welding and
welding in areas with high levels of natural sunlight.
2. Medium Setting - suitable for most indoors and outdoors
welding.
3. High Setting - suitable for low amperage welding and
welding in areas with low light conditions, especially for
low amperage argon-arc welding.
GRINDING MODE
You can also use the welding helmet to protect your face during
grinding. This will prevent the filter cartridge from darkening
when bright sparks are created.
Press the weld/grind button (C) twice to activate, then hold the
down until Shade number 4 appears in the LCD. The grinding
icon (I) will appear on the LCD and the weld/grind button LED
will flash red to confirm grind mode is set. You cannot adjust the
shade number and memory save/retrieve functions grind mode.
MEMORY SETTING
Press the memory button (F) and the identical number icon (M,
N, O) will appear. Hold the memory button until it stops
flashing to store the current settings. Existing saved settings
can be overwritten by the same process.
Press a memory button once to retrieve and use the saved setting.
Press any button on the left side to ignore the memory settings.
The general settings are stored when the helmet is shut off. The
general settings remain when the helmet is turned on. These
settings are lost if a saved setting is used.
Tabla de contenidos
Idiomas:
Otros manuales de Accesorios para motocicletas de PROPOINT
Manuales populares de Accesorios para motocicletas de otras marcas
SRC
SRC B-TRK502-01-01-SL Manual de usuario
3M
3M Speedglas 9100 MP Manual de usuario
hepco & becker
hepco & becker 6307520 00 01 Manual de usuario
HOMCOM
HOMCOM AA0-077 Manual de usuario
hepco & becker
hepco & becker 6307558 00 01 Manual de usuario
Wunderkind Custom
Wunderkind Custom 106503-F15 Guía del usuario
