Pro-Lift T-3101 Instrucciones de uso

Printed in China

T-3101-M1_082018

Operating Instructions & Parts Manual

Engine Stand

Model Number

T-3101

Capacity

1000 lb

Shinn Fu Company of America, Inc.

10939 N. Pomona Ave.

Kansas City, MO 64153

Phone (816)891-6390, fax (816)891-6599

To avoid crushing and related

injuries: NEVER work on, under

or around a vehicle supported

by dollies.

WARNING: Cancer and Reproductive Harm.

AVERTISSEMENT: Cancer et dommages au système reproducteu

ADVERTENCIA: Cáncer y daño reproductivo.

www.P65Warnings.ca.gov

This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

Obey all safety messages that follow this symbol to avoid possible injury or death.

!WARNING

Save these instructions. For your safety,

read and understand the information

contained within. The owner and operator

shall have an understanding of this product

and safe operating procedures before

attempting to use this product. Instructions

and safety information shall be conveyed in

the operator’s native language before use

of this product is authorized. Make certain

that the operator thoroughly understands

the inherent dangers associated with the

use and misuse of the product. If any doubt

exists as to the safe and proper use of this

product as outlined in this factory authorized

manual, remove from service. Inspect

before each use. Do not use if broken,

bent, cracked or otherwise damaged parts

are noted. If the engine stand has been

or suspected to have been subjected to a

shock load (a load dropped suddenly and

unexpectedly upon it), discontinue use

until checked out by an authorized factory

service center. Owners and operators of this

equipment shall be aware that the use of

this equipment may require special training

and knowledge. It is recommended that

an annual inspection be done by qualied

personnel and that any missing or damaged

parts, decals, warning/safety labels or

signs be replaced with factory authorized

replacement parts only. Any engine stand

that appears to be damaged in any way,

is worn or operated abnormally shall be

removed from service immediately. Labels

and owner’s manuals are available from

manufacturer (see Replacement Parts,

page 5).

PRODUCT DESCRIPTION

Pro-Lift Engine Stands are designed to

safely support rated capacity engines.

Welded steel tube construction, heavy

gauge steel plate head plates and mounting

arms along with compliance with factory

standards ensure safety, strength and

stability.

BEFORE USE

1. Inspect stands before each use. Do

not use if bent, broken or cracked

components are noted. Ensure that

casters/wheels and head plate rotate

freely. Check for and tighten any loose

assemblies.

2. Verify that the product and the application

are compatible.

3. Before using this product, read the

owner’s manual completely and

familiarize yourself thoroughly with the

product and the hazards associated with

its improper use.

Figure 1 - Typical Engine Stand

Nomenclature

rotating

mechanism

lock pin

handle

head plate

mounting arm

rear leg

center beam

front caster front leg

rear wheel

upright

Figure 2 - Assembly illustration for model

T-3101

ASSEMBLY

Model: T-3101 ( see Figure 2 )

Important: Reference numbers are for

assembly purpose only. See replacement

parts illustration for ordering replacement

parts.

1. Attach 2 front casters (Ref. No. 15) using

the lock washers (Ref. No. 13) and nuts

(Ref. No. 12).

2. Attach 2 rear wheels (Ref. No. 3) using

the washers (Ref. No. 2) and snap-rings

(Ref. No. 1).

3. Attach upright (Ref. No. 16) to the rear

leg (Ref. No. 4) using the M12 x 80 bolt

(Ref. No. 5), washer (Ref. No. 6), lock

washer (Ref. No. 7) and nally the hex

nut (Ref. No. 8).

4. Attach the center beam (Ref. No. 10) to

the front leg assy. (Ref. No. 11) using two

M12 x 80 bolts (Ref. No. 5), lock washer

(Ref. No. 7) and hex nut (Ref. No. 8).

5. Slide mounting plate (Ref. No. 20) into the

collar portion of the upright (Ref. No. 16),

align rotating position holes and insert

lock pin (Ref. No. 17).

6. Attach the four mounting adapter arms

(Ref. No. 21) to the slotted portion of the

mounting plate (Ref. No. 20) using M14

x 60 bolts (Ref. No. 22), lock washers

(Ref. No. 14), at washers (Ref. No. 13)

and hex nut (Ref. No. 12).

7. Insert handle (Ref. No. 19) into the hole

in the stem portion of the mounting plate

(Ref. No. 20) which protrudes from the

rear of the collar of the upright (Ref.

No. 16).

8. Attach the handle grips (Ref. No. 18)

onto both ends of handle (Ref. No. 19).

Study, understand, and follow all

instructions provided with and on this

device. Do not exceed rated capacity. Use

only on hard, level surface. Never put any

portion of your body under engine when it

is supported by the engine stand. Use only

hardened, appropriately sized bolts to

secure engine to stand. Center the engine

on mounting plate and ensure attaching

hardware is tightly fastened. Off center

loading may cause the engine to rotate

unexpectedly and cause the loaded stand

to tip over. Lock mounting plate rotating

mechanism before beginning engine

service. Unlock rotating mechanism

slowly and carefully. Do not modify or alter

this product. Do not use this device for

any purpose other than that for which it is

intended. Failure to heed these markings

may result in personal injury

!WARNING

OPERATION

1. Ensure application is compatible with

product.

2. Align engine with stand, then adjust

mounting arms to match bell housing

mounting bolt holes.

Rotational lock must be secure be-

fore applying load.

3. Carefully secure engine so that load is

centered on stand. Secure with suitable

high strength stud bolts and at wash-

ers. Ensure threads are compatible with

your engine. Use at washers on both

sides of head plate.

4. To rotate engine, carefully remove pin.

Use handle to rotate, then secure by

re-installing pin (Refer to Fig. 2).

5. Check to ensure stand is secure before

working on or around stand. Never work

under loaded stand.

Note: Do not move loaded stand off hard

smooth, level surface!

MAINTENANCE

Periodically inspect each stand. Ensure all

parts move freely. Apply very light coating of

grease to head plate collar. If rust appears,

sand affected area and cover with suitable

utility paint.

REPLACEMENT PARTS

Available Parts: Please refer to the parts drawing when ordering parts. Not all components

of the stand are replacement items, but are illustrated as a convenient reference of loca-

tion and position in the assembly sequence. When ordering parts, give model number,

serial number and description below. Call or write for current pricing: phone (816) 891-

6390, fax (816) 891-6599 or contact Pro-Lift Customer Support. 10939 N. Pomona Ave.,

Kansas City, MO 64153.

Model T-3101

Part No. Description Quantity

1 head plate 1

2 mounting arm assembly 4

3 front Wheel assembly 2

4 rear Caster assembly 2

5 handle assembly 1

6 lock pin 1

7 hardware kit (not shown) all nuts and bolts

-- label 1

-- owner’s manual 1

Figure 4 - Replacement Parts Illustration for Model T-3101

ONE YEAR LIMITED WARRANTY

For a period of one (1) year from date of purchase, SFA Companies will repair

or replace, at its option, without charge, any of its products which fails due to a defect in

material or workmanship, or which fails to conform to any implied warranty not excluded

hereby.

Performance of any obligation under this warranty may be obtained by returning

the warranted product, freight prepaid, to SFA Companies Warranty Service Department,

10939 N. Pomona Ave., Kansas City, MO 64153.

Except where such limitations and exclusions are specically prohibited by ap-

plicable law, (1) the

CONSUMER’S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACE-

MENT OF DEFECTIVE PRODUCTS AS DESCRIBED ABOVE, and (2) SFA Companies

SHALL NOT BE LIABLE FOR ANY

CONSEQUENTIAL OR INCIDENTAL DAMAGE OR LOSS WHATSOEVER, and (3) THE

DURATION OF ANY AND ALL EXPRESSED AND IMPLIED WARRANTIES, INCLUDING

WITHOUT LIMITATION, ANY WARRANTIES OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE, IS LIMITED TO A PERIOD OF ONE (1) YEAR FROM

DATE OF PURCHASE.

Some states do not allow limitations on how long an implied warranty lasts, so the

above limitation may not apply to you. Some states do not allow the exclusion or limitation

of incidental or consequential damages, so the above limitation or exclusion may not apply

to you. This warranty gives you specic legal rights, and you may also have other rights

which vary from state to state.

NOTES:

Tabla de contenidos

Otros manuales de Rack y soporte de Pro-Lift

Pro-Lift

Pro-Lift G5ZL Manual de usuario

Pro-Lift

Pro-Lift WMH Series Manual de usuario

Pro-Lift

Pro-Lift G4U-WM Manual de usuario

Pro-Lift

Pro-Lift G4U-LCD Manual de usuario

Pro-Lift

Pro-Lift T-6902 Instrucciones de uso

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario