Premier Mounts PTDM2 Manual de usuario
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
1321 S. State College Blvd., Fullerton, CA 92831 USA
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
PTDM2
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
Included components
Required for installation
PTDM2
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
Maximum Flat Panel Weight:
100 lb. / 45.35 kg.
x4
M4 x 12mm
screw
x4
M4 x 16mm
screw
x4
M4 x 25mm
screw
x4
M6 x 12mm
screw
x4
M6 x 16mm
screw
x4
M6 x 25mm
screw
x4
M8 x 16mm
screw
x4
M8 x 25mm
screw
x4
5/16” x 3”
Lag Bolts
x4
Washers
x4
Universal 3
HoleWasher
x8
Universal
Spacer
x1
Depth Measuring
Straw x1
Page 2
Pencil Level
1/4” Drill Bit for
Wood Stud
Electronic Stud Finder
Socket Wrench Phillips Tip Screwdriver Tape Measure
Hand Held Drill
Protective Eyewear
1/2” Socket
O
N
x1
Wall Plate
x2
Mounting Brackets
Lock-it Barrel
1
PTDM2
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
Page 3
Introduction
Directional Mounting Arrow
The Directional Mounting Arrow stamped
into the top of the PTDM2 wall mount
indicates which edge is the top.
Mounting Safety
Two people are recommended for the
installation of this mount.
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
XX
You must secure the wall plate to two (2)
wall studs with a minimum of four (4) lag
bolts (2 lag bolts for each stud found).
Use a stud nder to determine the exact
center of wall studs in the vicinity of the wall
plate.
Use a pencil to mark the exact center of each
of the wall studs.
PTDM2
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
Page 4
3
2Two people are recommended for this step; one
person to level the wall plate and another person
to mark the wall stud location.
Place the wall plate against the wall in the desired
viewing location.
Adjust the wall plate to align the mount slots in the
wall plate with the center of the wall studs.
Level the wall plate.
Use a pencil to mark the upper right mounting
location along the center of the wall stud.
Drill a “pilot hole” in the center of the upper right mark
using a 1/4” drill bit and power drill.
Only use a 1/4” drill bit when drilling the pilot
holes.
4 Place the wall plate against the wall and align it with
the pilot hole.
Insert one (1) 5/16” x 3″ lag bolt and one (1) 5/16”
washer into the upper right mounting hole and
tighten using a socket wrench and 1/2” socket.
Do not overtighten the lag bolt.
5
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100 Page 5
Level the wall plate.
Use a pencil to mark the remaining three (3)
mounting locations along the center of each wall
stud.
PTDM2
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
PTDM2
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
Page 6
7
6Two people are recommended for this step; one
person to level the wall plate and another person
to drill the pilot holes.
Drill a “pilot hole” in the center of each of the marks with
a power drill and a 1/4” drill bit.
Only use 1/4” drill bit when drilling the pilot holes.
Insert one (1) 5/16” x 3” lag bolt and one (1) 5/16”
washer into each pilot hole.
Tighten all lag bolts using a socket wrench and 1/2”
socket.
Do not overtighten the lag bolts when attaching
the mount to the wall. Improper installation may
result in personal injury or property damage.
Proceed to the “Installing the Mounting Bracket”
section.
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100 Page 7
Installing the Mounting Bracket
Small Straw or Toothpick
Small Straw
or Toothpick
Small Straw
or Toothpick
Marking the 1/8”
Allowance
Depth Plus 1/8” Allowance
Mark
Depth Plus 1/8” Allowance
Mark
Insert a small straw or toothpick into the threaded
inserts found on the back of the at panel.
Use a pencil to mark the depth of the threaded
insert on the small straw or toothpick.
Mark the straw or toothpick 1/8” above the depth of
the threaded insert, as shown in Figure 1.
Insert the small straw or toothpick into the remaining
threaded inserts to compare and verify their depth
using the straw or toothpick’s 1/8” allowance mark.
Locate the correct diameter screw for the threaded
insert.
If the screw you selected is longer than the 1/8”
allowance mark on the small straw or toothpick,
as shown in Figure 2 and Figure 3, do not use
this screw. The screw length must not bypass the
mark.
Test each size of the screws provided.
The correct screws should thread easily into the
mounting point and not pull out when tension is
applied.
Proceed to the “Universal Washer Installation”
section.
Selecting the Mounting Hardware
PTDM2
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
PTDM2
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
Page 8
Premier Mounts’ Universal Washers are designed to
accommodate the various M4, M5, M6 and M8 hole
sizes required by at panels.
Do not place excessive pressure on the back of
the at panel, as this may damage your at panel.
The Universal Washer must be installed between
the head of the mounting screw and the mounting
bracket as shown.
Does your at panel have:
●Recessed mount points?
●Uneven mount points?
●A curved back?
●Any obstruction near the mount point?
If Yes, you must install Universal Spacers. Remove the
mounting brackets, Universal Washers, and mounting
screws from the back of the at panel. Proceed to the
“Universal Spacer Installation” section.
If No, skip to the “Attaching the Mounting Bracket
to the Flat Panel” section.
Premier Mounts’ Universal Spacers allow you to
attach the mounting bracket to at panels which have
recessed or uneven mount points. Each Universal
Spacer adds ¼˝ to the distance between the mounting
bracket and your at panel.
The Universal Spacers must be stacked and
oriented as shown.
The Universal Spacers must only be installed
between the mounting bracket and your at panel.
The Universal Spacers will t M4, M5, M6 and M8
screw sizes.
Proceed to the “Attaching the Mounting Bracket to
the Flat Panel” section.
Flat Panel
Universal Washer
Universal Spacer
Mounting Bracket
Mount Point
Mounting Screw
M8
M5, M6
M4
1˝ ¼˝
Universal Washer Installation
Universal Spacer Installation
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100 Page 9
PTDM2
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
Attaching the Mounting Bracket to the Flat Panel
This section presumes that you have read and
understood these sections:
●Selecting the Proper Mounting Hardware
●Universal Washer Installation
●Universal Spacer Installation
Place your at panel screen-side down on a soft, at
surface.
Identify the number and location of the thread
inserts on the back of your at panel.
Align the holes on each mounting bracket with the
thread inserts on the back of your at panel.
Secure each mounting bracket to your at panel by
inserting a minimum of two (2) screws per bracket.
Do not overtighten the mounting hardware.
Proceed to the “Lock-It™ Security Barrel
Installation (Optional)” section.
Lock-It™ Security
Barrel
Locking Screw
Lock-it™ Security Barrel Installatin (Optional)
Optional security congurations include:
- PCB-CSL1 (sold separately)
- Padlock (Combination or Keyed; commercially
available)
Please read the following directions to install the
security barrel:
Remove the locking screw from the mounting
bracket.
Place the locking screw into and through the
security barrel (see illustration below).
Re-insert the locking screw and security barrel into
the mounting bracket.
Tighten the locking screw and security barrel until
seated in the mounting tab.
Do not thread the locking screw any further once
it is even with the mounting tab (see illustration to
the right). Threading the locking screw any further
will prevent you from safely attaching the at
panel to the wall plate.
Do not overtighten the locking screw.
Proceed to the “Attaching the Mounting Bracket to
the Flat Panel” section.
Mounting Tab
PTDM2
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
Page 10
Attaching the Flat Panel to the Wall Plate
This section requires two people.
Do not release your at panel until you are
certain that top and bottom hooks of both
mounting brackets are securely seated on
the upper and lower mounting rails of the
wall panel.
Raise the at panel past the top and bottom
mounting rails on the wall panel.
Slide the at panel down slowly, keeping it
close to the wall.
Engage the top and bottom mounting
brackets to the rails of the wall plate.
Proceed to the “Mounting Bracket
Adjustments” section.
Mounting Bracket Adjustments
M6 x 35mm
Locking Screw
(1 per Bracket)
M6 x 30mm
Leveling Screw
(1 per Bracket)
If your at panel is tilted too far to one side, the leveling
screws will allow you to compensate for this tilt by
simply adjusting the screws with a screwdriver.
Loosen both locking screws.
Adjust the tilt of your at panel.
Tighten both locking screws.
Caution!
It is possible to dislodge your at panel while you
level your at panel. Use extreme caution until
you tighten the locking screws.
After you have nished leveling your at panel, be sure
to tighten the two (2) M6 x 35mm locking screws.
Do not overtighten the locking screws.
Leveling Screw Adjustment
Locking Screw Adjustment
Otros manuales para PTDM2
1
Tabla de contenidos
Otros manuales de Rack y soporte de Premier Mounts
Premier Mounts
Premier Mounts PBC-1.5 Series Manual de usuario
Premier Mounts
Premier Mounts PRC Manual de usuario
Premier Mounts
Premier Mounts INW-AM200 Manual de usuario
Premier Mounts
Premier Mounts AM175 Manual de usuario
Premier Mounts
Premier Mounts CTM-MS1 Manual de usuario
Premier Mounts
Premier Mounts PFM-32C1 Manual de usuario
Premier Mounts
Premier Mounts PSD-TTS/B Manual de usuario
Premier Mounts
Premier Mounts CTM-MS1 Manual de usuario
Premier Mounts
Premier Mounts UFA Manual de usuario
Premier Mounts
Premier Mounts GB-PIPE1 Manual de usuario
Premier Mounts
Premier Mounts SpiroLock SPI-PRO Manual de usuario
Premier Mounts
Premier Mounts PSD-TL Manual de usuario
Premier Mounts
Premier Mounts RTM Series Manual de usuario
Premier Mounts
Premier Mounts PP-HDFCP Manual de usuario
Premier Mounts
Premier Mounts Universal Flat-Only Mount UFM Manual de usuario
Premier Mounts
Premier Mounts USA Manual de usuario
Premier Mounts
Premier Mounts UFA Manual de usuario
Premier Mounts
Premier Mounts AM100 Manual de usuario
Premier Mounts
Premier Mounts PBC- UMW Manual de usuario
Premier Mounts
Premier Mounts SHLF-EQ Manual de usuario
