Premier Mounts PSD-TL Manual de usuario

INSTALLATION INSTRUCTIONS

PSD-TL

60” / 72” / 84”

Floor Stand

NORTH AMERICA

3130 East Miraloma Avenue

Anaheim, CA 92806 USA

USA and Canada –

Phone: 800-368-9700

Fax: 800-832-4888

EUROPE

Swallow House,

Shilton Industrial Estate,

Shilton, Coventry, England CV79JY

Phone: +44 (0) 2476 614700

Fax: +44 (0) 2476 614710

Other Locations – Phone: (001)-714-632-7100; Fax: (001)-714-632-1044

©Premier Mounts 2009

9532-565-001-03

Installation Instructions Page 3

Parts List Congratulations on the purchase of your new Premier Mounts PSD-TL stand. This stand is shipped with all proper

installation hardware and components. Make sure that none of these parts are missing and/or damaged before

beginning installation. If there are parts missing and/or damaged, please stop the installation and contact Premier Mounts

(800) 368-9700.

PSD-TL Base (Qty 1) Support Poles (Qty 2)

Screwdriver

(Not Supplied) 1/2” Socket and Socket

Wrench (Not Supplied)

M10 x 12mm Slotted

Hex Head (Qty 4)

PSD-SPA (Qty 1) M8 x 10mm Set Screw (Qty 10)

The length will vary depending

on the application.

84”

72”

60”

M10 Flat Washers

(Qty 4)

Shelf (Optional)

NOTE: The max weight capacity for

the shelf is 25lbs.

PSD-TL

Installation Tools (not supplied)

5/32” Allen Wrench

Page 4 Installation Instructions

PSD-TL

Features

Congratulations on the purchase of your new Premier Mounts PSD-TL Floor Stand. When combined with a mount, our floor stand

allows you to place a flat-panel in a horizontal or vertical position (with PSM and RTM-L/S mounts only). The flat-panel height

is adjustable to any point along the stand’s vertical support poles to achieve the perfect viewing level. The PSD-TL mates directly to

our CTM, USA, UFA, RTM-L/S or PSM series of mounts.

PSD-TL Base

USA Mount

CTM Series MountRTM-S Mount RTM-L Mount

UFA Mount

PSD-TL Base

PSD-TL Base PSD-TL Base PSD-TL Base

PSM Series Mount

PSD-TL Base

Installation Instructions Page 5

PSD-TL

Support Pole Installation

Remove the stand out of the box and check for all proper hardware, if missing any hardware please call Premier Mounts.

A mount is required to complete the PSD-TL system. Refer to the mount’s installation instructions to install the mounting

bracket.

Step 1. Insert the poles inside the base columns of the

PSD-TL, making sure they are fully seated on

the base with the cable access holes facing the

rear of the base.

Step 2. Secure the support poles by inserting and

tightening the four (4) M8 x 10mm locking set

screws that are located on the back of the

mounting columns.

Step 3. Tighten set screw with the supplied Allen

wrench. Do not over tighten the screws.

Step 1. Install the PSD-SPA (mount adapter) over the top

of the support poles and secure it at the desired

height with the four (4) M8 x 10 set screws

(supplied).

Step 2. Use the Allen wrench (supplied) to secure the

adapter to the support poles.

Adapter Installation

PSD-SPA Adapter

(facing forward)

Allen Wrench

M8 x 10mm

Set Screws

Support Poles

2” Diameter Support Poles

Allen Wrench

Mounting Columns

PSD-TL

Mounting Screws

ThePSD-SPAadapterisusedwiththeCTMand

PSM Series mounts only. The PSD-SPA is not

needed when installing the USA, UFA or

RTM-L/S mounts.

Please see Page 8 for optional shelf installation instructions.

The PSD-SPA must be facing forward when

mounted to the support poles.

Page 6 Installation Instructions

CTM and PSM Series Installation

PSD-TL

This stand is intended for use only with the maximum weights indicated. Use with products heavier than the

maximum weights indicated may result in instability causing possible injury.

The flat-panel is very heavy; two people are required to lift the flat-panel and secure it to the stand.

To install the mounting brackets to the flat-panel, refer to the CTM and PSM installation instructions.

Step 2. Raise the flat-panel with the left and right brackets

secured to the flat-panel and insert the bottom and top hooks

from the mounting arms to the top and bottom rods found

on the CTM back plate.

Step 3. Secure the mounting arms with the two (2) M6 x 12mm

Safety knobs (supplied with the CTM mount).

Step 4. Insert and tighten two (2) M6 x 30mm lateral shift screws

(supplied with the CTM mount) on the bottom of the

mounting arms. These screws will prevent the flat panel

from moving side-to-side.

The safety knobs MUST be used. Failure to

do so may result in damage to the flat-panel or

personal injury.

CTM Back

Plate

Flat-Panel

PSD-TL Base

(facing forward)

CTM Series

Mounting Brackets

M6 x 12mm

Safety Knobs

Step 1. For the CTM-Series, secure the back plate to

the four (4) threaded mounting points found on

the PSD-SPA with the four (4) M10 x 12 bolts

and flat washers (supplied).

The directional arrow must be pointing

up prior to installation. Secure the follow-

ing plates to the secured PSD-SPA on the

support poles.

Installing the CTM

Support Poles

PSD-SPA Adapter

Directional Arrow

CTM Back Plate

M10 x 12mm

Bolts

M10 Flat Washers

PSD-TL Base

(facing forward)

M6 x 30mm Lateral

Shift Screws

Installation Instructions Page 7

PSD-TL

USA, UFA and RTM-L/S Installations

The USA, UFA, RTM-L and RTM-S Series of stand/cart mounts attach to the PSD-TL without the use of the PSD-SPA.

Please follow the installation instructions that are packaged with these mounts.

Step 1. Slide the USA, UFA, RTM-L and RTM-S Series over and onto the support poles.

Step 2. Determine the desired height.

Step 3. Tighten the set screws, located at the rear of each mount, using the supplied Allen wrench.

Step 1. For the PSM-Series, secure the back plate to the four (4)

threaded mounting points found on the PSD-SPA with the

four (4) M10 x 12 bolts and flat washers (supplied).

Installing the PSM Support Poles

PSD-SPA Adapter

Directional Arrow

PSM Back Plate

M10 x 12mm

Bolts

M10 Flat Washers

Step 2. Raise the flat-panel display with the mounting bracket

secured and insert the four (4) tab openings from the PSM

mount to the four (4) receiving tabs found on the back

plate.

Step 3. Push the flat-panel display down, right and down again to

lock the mount together.

Step 4. Make sure all tab openings are interlocked with the

receiving tabs before letting go of the flat-panel.

Step 5. Secure the brackets with two (2) M6 x 12mm Phillips

(supplied with the PSM mount) screws for additional

security.

PSM Back Plate

PSM Mounting

Bracket

Flat-Panel

M6 x 12mm

Screws

PSD-TL Base

(facing forward)

PSD-TL Base

(facing forward)

Page 8 Installation Instructions

PSD-TL

Optional Installations

Floor Installation

Step 1. If securing the base to the floor, use

(commercially available) hardware.

Step 1. The shelf must be attached before the flat-panel

and PSD-SPA adapter is installed to the

stand.

Step 2. Attach the shelf to the poles by sliding the shelf

over the poles and down into position.

Step 3. Determine the final height and secure the shelf

using four (4) M8 x 10mm set screws.

Step 4. Tighten these screws using the supplied Allen

wrench.

Do not install the optional shelf higher than

39”.

If using a shelf, please install prior to

attaching the flat-panel.

Suitable Hardware

(Commercially Available)

Shelf Installation

Optional

Shelf

M8 x 10mm

Set Screws

Allen Wrench

DO NOT load the Stand past the maximum

weight capacity.Failure to comply with this

warning may result in Stand instability

leading to equipment damage or personal

injury.

WARNING

PSD-TL Base

(facing forward)

PSD-TL Base

(not facing forward)

Installation Instructions Page 9

PSD-TL

Technical Specifications

All measurements are in inches(mm).

Tabla de contenidos

Otros manuales de Rack y soporte de Premier Mounts

Premier Mounts

Premier Mounts PFC-OMND Manual de usuario

Premier Mounts

Premier Mounts MM-HP15 Manual de usuario

Premier Mounts

Premier Mounts SHLF-VC Manual de usuario

Premier Mounts

Premier Mounts AST-2446 Manual de usuario

Premier Mounts

Premier Mounts PDS-PLUS Manual de usuario

Premier Mounts

Premier Mounts ECM-3763S Manual de usuario

Premier Mounts

Premier Mounts 7170-0977 Series Manual de usuario

Premier Mounts

Premier Mounts PSD-TTS/B Manual de usuario

Premier Mounts

Premier Mounts LMVSP Manual de usuario

Premier Mounts

Premier Mounts PSD-TS Manual de usuario

Premier Mounts

Premier Mounts PP-HDFCP Manual de usuario

Premier Mounts

Premier Mounts TTS-BASE-L Manual de usuario

Premier Mounts

Premier Mounts PBL-200 Manual de usuario

Premier Mounts

Premier Mounts MVWC-3X3 Manual de usuario

Premier Mounts

Premier Mounts UNI Manual de usuario

Premier Mounts

Premier Mounts RFM Manual de usuario

Premier Mounts

Premier Mounts ECM-3763T Manual de usuario

Premier Mounts

Premier Mounts Press and Release LMVP Manual de usuario

Premier Mounts

Premier Mounts GB-AVSTOR4 Manual de usuario

Premier Mounts

Premier Mounts LMVLF Manual de usuario

Premier Mounts

Premier Mounts AST-2446-2 Manual de usuario

Premier Mounts

Premier Mounts ECM-3000 Manual de usuario

Premier Mounts

Premier Mounts PBC-UM Series Manual de usuario

Premier Mounts

Premier Mounts Universal Tabletop Stand PSD-TTS/C Manual de usuario

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario